Nissan Qashqai J11. Manual — part 1800
WW-78
< REMOVAL AND INSTALLATION >
FRONT WIPER
3.
Engage wiper refill stopper hole, and wiper blade pawl with imprinted “SET” mark (“
” mark).
4.
Check the following items after installing.
• Wiper refill thoroughly fits in the pawl on wiper blade.
• Wiper refill is not deformed (waving / tucking).
NOTE:
When the vertebra is detached
• Insert the vertebra
into the wiper blade to the same bending
direction.
• If a vertebra has a notch, fit it to a protrusion inside the wiper refill.
WIPER DRIVE ASSEMBLY
WIPER DRIVE ASSEMBLY : Removal and Installation
INFOID:0000000010479831
REMOVAL
1.
Remove cowl top cover. Refer to
EXT-29, "Removal and Installation"
.
2.
Disconnect wiper motor harness connector, disengage wiper motor harness clip, remove wiper drive
assembly fixing bolts, and then remove wiper drive assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing, temporarily tighten all fixing bolts, and then tighten bolts to specified torque.
JPLIA1586ZZ
REAR WIPER
WW-79
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER
Exploded View
INFOID:0000000010479850
WIPER ARM
WIPER ARM : Removal and Installation
INFOID:0000000010491763
CAUTION:
Clean the rear windshield glass and rear wiper refill so that the rear windshield glass may not be dam-
aged by dust, etc.
REMOVAL
1.
Operate rear wiper to the auto stop position.
2.
Open rear wiper arm cover.
3.
Remove rear wiper arm fixing nut.
4.
Remove wiper arm from the vehicle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Clean wiper arm installation location as shown in the figure,
and then fully insert wiper arm to prevent nut from being loos-
ened by shakiness.
• When installing the wiper arm, install so that it is within the standard. For the standard, refer to
Rear wiper refill
Rear wiper motor
Rear wiper pivot seal
Rear wiper arm
Rear wiper arm cover
Rear wiper blade
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA5160GB
SKIA0082J
WW-80
< REMOVAL AND INSTALLATION >
REAR WIPER
• After installation, operate front wiper, and then check that the wiper blades stop at the specified
position. Refer to
WW-80, "WIPER ARM : Adjustment"
.
WIPER ARM : Adjustment
INFOID:0000000010491764
REAR WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of back door glass and top of wiper blade center.
Standard clearance
WIPER BLADE
WIPER BLADE : Removal and Installation
INFOID:0000000010479853
REMOVAL
1.
Lift up and hold rear wiper arm.
2.
Remove rear wiper blade
from rear wiper arm
while rotating rear wiper blade in the direction indi-
cated by the arrow as shown in the figure.
CAUTION:
After the wiper blade is removed, wrap the wiper arm tip with a shop cloth and fold it down so that
the wiper arm does not fall against and damage the windshield glass.
INSTALLATION
Install in the reverse order of removal.
WIPER MOTOR
L
: 40.5 mm (1.59 in)
JPLIA0966ZZ
JMLIA1989ZZ
REAR WIPER
WW-81
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER MOTOR : Removal and Installation
INFOID:0000000010491661
REMOVAL
1.
Remove the rear wiper arm. Refer to
WW-79, "WIPER ARM : Removal and Installation"
.
2.
Remove the back door lower finisher. Refer to
INT-31, "Removal and Installation"
.
3.
Disconnect the harness connector from the rear wiper motor.
4.
Remove the rear wiper motor fixing bolts, and then remove rear wiper motor.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing, temporarily tighten all fixing bolts, and then tighten bolts to specified torque.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст