Nissan Qashqai J11. Manual — part 520
EC9-236
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0403 EGR VOLUME CONTROL VALVE
P0403 EGR VOLUME CONTROL VALVE
DTC Logic
INFOID:0000000010309164
DTC DETECTION LOGIC
NOTE:
If DTC P0380 is displayed with DTC P0641, first perform the trouble diagnosis for DTC P0641 Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC9-236, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010502693
1.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE
Visually check high pressure EGR volume control valve for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
Check ECM harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE HARNESS CONNECTOR CONNECTIONS
Check high pressure EGR volume control valve harness connector connection.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check high pressure EGR volume control valve circuit for open and short.
DTC No.
CONSULT screen terms
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P0403
EGR VLV CMD CIRC
(Exhaust gas recircula-
tion “A” control circuit)
• 1.DEF: —
• 2.DEF: OPERATION
TEMPERATURE TOO
HIGH
• ECM detects high Pressure EGR volume control
valve command circuit is short to ground.
• ECM detects high Pressure EGR volume control
valve command circuit is short to power.
• ECM detects an over temperature of high Pressure
EGR volume control valve.
• Harness or connectors
(High Pressure EGR volume control
valve command circuit is open or
shorted.)
• High Pressure EGR volume control
valve
P0403 EGR VOLUME CONTROL VALVE
EC9-237
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
DTC CONFIRMATION PROCEDURE
1.
Erase DTC.
2.
Perform DTC confirmation procedure again. Refer to
.
Is the DTC P0403 displayed again?
YES
>> GO TO 6.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
6.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE MOTOR
EC9-237, "Component Inspection (High Pressure EGR Volume Control Valve Motor)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace error-detected parts.
Component Inspection (High Pressure EGR Volume Control Valve Motor)
INFOID:0000000010309166
1.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE MOTOR
1.
Turn ignition switch OFF.
2.
Disconnect high pressure EGR volume control valve harness connector.
3.
Check resistance between high pressure EGR volume control valve terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace high pressure EGR volume control valve.
+
-
Continuity
ECM
High pressure EGR volume
control valve
Connector
Terminal
Connector
Terminal
F83
144
F14
1
Existed
148
2
High pressure EGR volume
control valve
Resistance (Approx.)
+
-
Terminal
1
2
2.35
Ω
EC9-238
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0409 EGR VOLUME CONTROL VALVE POSITION SENSOR
P0409 EGR VOLUME CONTROL VALVE POSITION SENSOR
DTC Logic
INFOID:0000000010309167
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC9-238, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309168
1.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE
Visually check high pressure EGR volume control valve for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
Check ECM harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE HARNESS CONNECTOR CONNECTIONS
Check high pressure EGR volume control valve harness connector connection.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE POSITION SENSOR CIRCUIT FOR OPEN
AND SHORT
1.
Turn ignition switch OFF.
2.
Check high pressure EGR volume control valve position sensor circuit for open and short.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0409
EGR VALVE POSITION SEN CIRC
(Exhaust gas recirculation sensor
“A” circuit)
• 1.DEF: SIGNAL INCOHERENCE
• A Voltage of high Pressure EGR
volume control valve position sen-
sor remains more than 4.5 V.
• A Voltage of high Pressure EGR
volume control valve position sen-
sor remains less than 0.5 V.
• Harness or connectors
(High pressure EGR volume control valve
control position sensor circuit is open or
shorted.)
• High pressure EGR volume control valve
control position sensor
P0409 EGR VOLUME CONTROL VALVE POSITION SENSOR
EC9-239
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
Is the inspection result normal?
YES
>> Replace High pressure EGR volume control valve.
NO
>> Repair or replace error-detected parts.
+
-
Continuity
ECM
High pressure EGR volume
control valve
Connector
Terminal
Connector
Terminal
F83
106
F14
6
Existed
108
4
110
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст