Nissan Qashqai J11. Manual — part 521
EC9-240
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0470 EXHAUST GAS PRESSURE SENSOR
P0470 EXHAUST GAS PRESSURE SENSOR
DTC Logic
INFOID:0000000010309172
DTC DETECTION LOGIC
NOTE:
If DTC P0470 is displayed with DTC P0651, and P2263, perform the trouble diagnosis for DTC P0651,
and P2263. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 5 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC9-240, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309173
1.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
1.
Turn ignition switch OFF.
2.
Check ECM harness connector connection.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK EXHAUST GAS PRESSURE SENSOR HARNESS CONNECTOR CONNECTIONS
Check exhaust gas pressure sensor harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK EXHAUST GAS PRESSURE SENSOR POWER SUPPLY CIRCUIT
Check the power supply of the exhaust gas pressure sensor.
Is the inspection result normal?
YES
>> GO TO 4.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0470
TBN UPSTR PRS SEN CIRC
(Exhaust pressure sensor “A”
circuit)
• 1.DEF: VOLTAGE TOO LOW
• 2.DEF: VOLTAGE TOO HIGH
• An excessively low voltage from the sensor
is sent to ECM.
• An excessively high voltage from the sensor
is sent to ECM.
Exhaust gas pressure sensor
+
-
Voltage
(Approx.)
Exhaust gas pressure sensor
Connector
Terminal
F135
3
Ground
5 V
P0470 EXHAUST GAS PRESSURE SENSOR
EC9-241
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
NO
>> Perform trouble diagnosis for power supply circuit.
4.
CHECK EXHAUST GAS PRESSURE SENSOR CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check exhaust gas pressure sensor circuit for open and short.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
CHECK EXHAUST GAS PRESSURE SENSOR
EC9-241, "Component Inspection (Exhaust Gas Pressure Sensor)"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace error-detected parts.
6.
DTC CONFIRMATION PROCEDURES
1.
Erase DTC.
2.
Perform DTC confirmation procedure again. Refer to
.
Is the DTC P0470 displayed again?
YES
>> GO TO 7.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
7.
CHECK TURBOCHARGER
Check turbocharger.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Exhaust Gas Pressure Sensor)
INFOID:0000000010309174
1.
CHECK EXHAUST GAS PRESSURE SENSOR
1.
Disconnect exhaust gas pressure sensor harness connector.
2.
Check the resistance between exhaust gas pressure sensor terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace exhaust gas pressure sensor.
+
-
Continuity
ECM
Exhaust gas pressure sen-
sor
Connector
Terminal
Connector
Terminal
F83
104
F135
3
Existed
126
1
138
2
Exhaust gas pressure sensor
Resistance (Approx.)
+
-
Terminal
2
1
100 k
Ω
EC9-242
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0471 EXHAUST PRESSURE SENSOR
P0471 EXHAUST PRESSURE SENSOR
DTC Logic
INFOID:0000000010309175
DTC DETECTION LOGIC
NOTE:
If DTC P0471 is displayed with DTC P0335, P0470, and P2226, perform the trouble diagnosis for DTC
P0335, P0470, and P2226. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DIAGNOSIS PROCEDURE
NOTE:
DTC P0471 can not duplicate.
>> Proceed to
EC9-242, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010502768
1.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
1.
Turn ignition switch OFF.
2.
Check ECM harness connector connection.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK EXHAUST GAS PRESSURE SENSOR HARNESS CONNECTOR CONNECTIONS
Check exhaust gas pressure sensor harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK EXHAUST GAS PRESSURE SENSOR POWER SUPPLY CIRCUIT
Check the power supply of the exhaust gas pressure sensor.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Perform trouble diagnosis for power supply circuit.
4.
CHECK EXHAUST GAS PRESSURE SENSOR CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check exhaust gas pressure sensor circuit for open and short.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0471
PRS UPSTR OF TBN
(Exhaust pressure sensor “A”
circuit range/performance)
• 1.DEF: INCORRECT SEN-
SOR MOUNTING
• 2.DEF: SIGNAL INCOHER-
ENCE
• Difference between barometric pressure
and exhaust pressure while engine
stopped.
• Exhaust pressure is excessively low while
engine is running.
Exhaust gas pressure sensor
+
-
Voltage
(Approx.)
Exhaust gas pressure sensor
Connector
Terminal
F135
3
Ground
5 V
P0471 EXHAUST PRESSURE SENSOR
EC9-243
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
CHECK EXHAUST GAS PRESSURE SENSOR
EC9-241, "Component Inspection (Exhaust Gas Pressure Sensor)"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace error-detected parts.
6.
DTC CONFIRMATION PROCEDURES
1.
Erase DTC.
2.
Perform DTC confirmation procedure again. Refer to
.
Is the DTC P0471 displayed again?
YES
>> GO TO 7.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
7.
CHECK TURBOCHARGER
Check turbocharger.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Exhaust Gas Pressure Sensor)
INFOID:0000000010309177
1.
CHECK EXHAUST GAS PRESSURE SENSOR
1.
Disconnect exhaust gas pressure sensor harness connector.
2.
Check the resistance between exhaust gas pressure sensor terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace exhaust gas pressure sensor.
+
-
Continuity
ECM
Exhaust gas pressure sen-
sor
Connector
Terminal
Connector
Terminal
F83
104
F135
3
Existed
126
1
138
2
Exhaust gas pressure sensor
Resistance (Approx.)
+
-
Terminal
2
1
100 k
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст