Nissan Juke (2014 year). Service Repair Manual — part 260
CVT FLUID
TM-305
< PERIODIC MAINTENANCE >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PERIODIC MAINTENANCE
CVT FLUID
Inspection
INFOID:0000000009752651
CHECKING CVT FLUID
The fluid level should be checked with the fluid warmed up to 50 to 80
°
C (122 to 176
°
F). The fluid level check
procedure is as follows:
1.
Check for fluid leakage.
2.
With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20
°
C (68
°
F), it takes about 10
minutes for the CVT fluid to warm up to 50 to 80
°
C (122 to
176
°
F).
3.
Park the vehicle on a level surface.
4.
Apply parking brake firmly.
5.
With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.
6.
Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.
7.
Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180
°
from the originally installed position,
then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.
CAUTION:
When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.
8.
Place the selector lever in “P” or “N” and check that the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until securely locked.
CVT FLUID CONDITION
SMA146B
SCIA1933E
SCIA1931E
SCIA1932E
Revision: 2013 October
2014 JUKE
TM-306
< PERIODIC MAINTENANCE >
[CVT: RE0F10B]
CVT FLUID
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of CVT.
Flush cooling system after repair of CVT.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of CVT. Refer to
Changing
INFOID:0000000009752652
CAUTION:
Replace drain plug gasket with new ones at the final stage of the operation when installing.
1.
Remove drain plug from oil pan.
2.
Remove drain plug gasket from drain plug.
3.
Install drain plug gasket to drain plug.
CAUTION:
Never reuse drain plug gasket.
4.
Install drain plug to oil pan.
5.
Fill CVT fluid from CVT fluid charging pipe to the specified level.
CAUTION:
• Use only recommended CVT fluid. Never mix with other fluid.
• Using CVT fluid other than recommended CVT fluid will deteriorate in driveability and CVT dura-
bility, and may damage the CVT, which is not covered by the warranty.
• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Sufficiently shake the container of CVT fluid before using.
• Delete CVT fluid deterioration date with CONSULT after changing CVT fluid.
6.
With the engine warmed up, drive the vehicle in an urban area.
NOTE:
When ambient temperature is 20
°
C (68
°
F), it takes about 10 minutes for the CVT fluid to warm up to 50 to
80
°
C (122 to 176
°
F).
7.
Check CVT fluid level and condition.
8.
Repeat steps 1 to 5 if CVT fluid has been contaminated.
9.
Select “Data Monitor” in “TRANSMISSION” using CONSULT.
10. Select “CONFORM CVTF DETERIORTN”.
11. Select “Erase”.
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
CVT fluid become
degraded due to
high temperatures.
Replace the CVT fluid and check the
CVT main unit and the vehicle for
malfunctions (wire harnesses, cool-
er pipes, etc.)
Milky white or
cloudy
Water in the fluid
Replace the CVT fluid and check for
places where water is getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
CVT
Replace the CVT fluid and check for
improper operation of the CVT.
ATA0022D
Drain plug – tightening torque
: Refer to
.
Recommended fluid and fluid capacity
: Refer to
MA-10, "Fluids and Lubricants"
.
Revision: 2013 October
2014 JUKE
CVT SHIFT SELECTOR
TM-307
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000009752653
Removal and Installation
INFOID:0000000009752654
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Disconnect battery cable from negative terminal. Refer to
PG-99, "Removal and Installation"
.
2.
Shift the selector lever to “N” position.
3.
Remove the center console. Refer to
IP-24, "Removal and Installation"
.
4.
Disconnect the CVT shift selector connector.
5.
Shift the selector lever to “P” position.
6.
Remove the key interlock cable from the CVT shift selector assembly. Refer to
(Without push starter system).
7.
Remove the control cable from the CVT shift selector assembly. Refer to
TM-311, "Removal and Installa-
8.
Remove the CVT shift selector assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Selector lever knob
2.
Lock pin
3.
Knob cover
4
Position indication panel
5.
CVT shift selector assembly
6.
Shift lock unit
7.
Key interlock rod*
8.
Position indicator bulb
:N·m (kg-m, in-lb)
*: Without push engine starter
JSDIA2341GB
Revision: 2013 October
2014 JUKE
TM-308
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CVT SHIFT SELECTOR
• When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and insert
the control cable until it stops.
Disassembly and Assembly
INFOID:0000000009752655
DISASSEMBLY
1.
Slide the selector lever knob cover (1) down.
CAUTION:
Never damage the knob cover.
2.
Pull out the lock pin (2).
3.
Pull the selector lever knob (3) and knob cover upwards to
remove them.
4.
Remove the position lamp.
5.
Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the CVT shift selector
assembly (2).
CAUTION:
Never damage the CVT shift selector assembly.
6.
Remove the shift lock unit from the CVT shift selector assembly.
7.
Disconnect the park position switch connector, detent switch
connector, and shift lock solenoid connector from the shift lock
unit.
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
• Follow the procedure below and place the selector knob onto the CVT shift selector.
1.
Install the lock pin (2) onto the selector lever knob (3).
2.
Install the knob cover (1) onto the selector lever knob.
3.
Press the selector lever knob onto the selector lever until it
clicks.
CAUTION:
• When pressing the selector lever knob onto the selector
lever, never press the selector lever knob button.
• Never strike the selector lever knob to press it into place.
Inspection
INFOID:0000000009752656
INSPECTION AFTER INSTALLATION
• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
JSDIA1624ZZ
JSDIA2401ZZ
JSDIA1802ZZ
JSDIA2401ZZ
Revision: 2013 October
2014 JUKE
CVT SHIFT SELECTOR
TM-309
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• The key can be removed only when the selector lever is in the “P” position. (With key interlock)
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
(With key interlock)
Revision: 2013 October
2014 JUKE
TM-310
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CONTROL CABLE
CONTROL CABLE
Exploded View
INFOID:0000000009752657
2WD MODELS
AWD MODELS
1.
Bracket B
2.
Lock plate
3.
Bracket A
4.
Transaxle assembly
5.
Control cable
6.
CVT shift selector assembly
A:
Manual lever
B:
Grommet
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA2352GB
Revision: 2013 October
2014 JUKE
CONTROL CABLE
TM-311
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Removal and Installation
INFOID:0000000009752658
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Remove the battery. Refer to
PG-99, "Removal and Installation"
2.
Remove the control cable from the CVT shift selector assembly. Refer to
TM-307, "Removal and Installa-
3.
Disengage the pawls (B) of the grommet (A), and pull down-
wards to remove.
4.
Remove the control cable installation nut from the manual lever.
1.
Lock plate
2.
Bracket A
3.
Transaxle assembly
4.
Control cable
5.
Bracket B
6.
CVT shift selector assembly
A:
Manual lever
B:
Grommet
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA2353GB
JSDIA1809ZZ
Revision: 2013 October
2014 JUKE
TM-312
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CONTROL CABLE
5.
Remove the lock plate (1).
6.
Remove center muffler from the mounting rubber and lower the
center muffler downward. Refer to
7.
Lift up the heat plate.
8.
Remove the control cable (1) from the bracket (2).
9.
Remove the control cable from the vehicle.
10. Remove bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the
pawls (B) make a click sound.
CAUTION:
• Place the grommet on the floor, then fasten it in place from
below the vehicle.
• Check that pulling down on the grommet does not discon-
nect it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1.
When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
JSDIA2643ZZ
:Vehicle front
JPDIA0107ZZ
JSDIA1809ZZ
JSDIA1624ZZ
Revision: 2013 October
2014 JUKE
CONTROL CABLE
TM-313
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Install the socket (A) onto the CVT shift selector.
CAUTION:
• Place the socket onto the CVT shift lever, then fasten it in
place from above.
• Check that the pulling on the socket does not disconnect
it.
Inspection
INFOID:0000000009752659
INSPECTION AFTER INSTALLATION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
JSDIA1810ZZ
Revision: 2013 October
2014 JUKE
TM-314
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
PADDLE SHIFTER
PADDLE SHIFTER
Exploded View
INFOID:0000000010198376
Removal and Installation
INFOID:0000000010198377
REMOVAL
1.
Park the vehicle on a level surface.
2.
Remove the driver air bag module. Refer to
SR-11, "Removal and Installation"
.
3.
Remove the steering wheel. Refer to
ST-9, "Removal and Installation"
4.
Remove the column cover. Refer to
IP-13, "Removal and Installation"
1.
Steering column assembly
2.
Paddle shifter (shift-down switch)
3.
Paddle shifter (shift-up switch)
: N·m (kg-m, in-lb)
AWDIA0557GB
Revision: 2013 October
2014 JUKE
PADDLE SHIFTER
TM-315
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Remove the paddle shifter connector (C) and (D) from paddle
shifter.
6.
Remove the paddle shifter mounting bolts (E) and nuts (F).
7.
Remove the paddle shifter from the steering column assembly.
INSTALLATION
Installation is in the reverse order of removal.
A
: Side of paddle shifter (shift-down switch)
B
: Side of paddle shifter (shift-up switch)
AWDIA0563ZZ
Revision: 2013 October
2014 JUKE
TM-316
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000009752660
Removal and Installation
INFOID:0000000009752661
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Shift the selector lever to the “N” position.
2.
Remove the selector lever knob. Refer to
TM-308, "Disassembly and Assembly"
3.
Shift the selector lever to the “P” position.
4.
Remove the center console. Refer to
IP-24, "Removal and Installation"
.
5.
Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.
6.
Remove the key interlock cable from the CVT shift selector.
7.
Remove the steering column lower cover and driver instrument
lower panel. Refer to
IP-13, "Removal and Installation"
.
1.
CVT shift selector assembly
2.
Key interlock cable
A:
Key cylinder
B:
Clip
C:
Clip
JSDIA2448ZZ
E
:Key interlock rod
JSDIA1797ZZ
Revision: 2013 October
2014 JUKE
KEY INTERLOCK CABLE
TM-317
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8.
Lift clip (A) in the direction of the arrow (
C) and remove in the
direction of the arrow (
D).
9.
Disconnect the key interlock cable from the key cylinder.
10. Disengage the clip and disconnect the key interlock cable from
the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the adjusting holder (A) onto the key interlock rod (B), then
install the casing cap (C) onto the CVT shift selector cable bracket
(D).
CAUTION:
• When installing the key interlock cable, never bend or twist
the cable forcefully.
• After connecting the key interlock cable to the CVT shift
selector cable bracket, be sure to check that the casing cap
is completely fastened to the cable bracket. If the casing cap
is easily displaced, replace the key interlock cable.
• While pressing the detent rod (B) down, slide the key interlock
cable slider (A) toward the key interlock rod (D) side, and install the
adjusting holder (C) and key interlock rod.
CAUTION:
• Never squeeze the pawls on the key interlock cable slider
when holding the slider.
• Never apply force in a perpendicular direction to the key
interlock rod when sliding the slider.
Inspection
INFOID:0000000009752662
INSPECTION AFTER INSTALLATION
• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
• The key can be removed only when the selector lever is in the “P” position.
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
1
:Key interlock cable
B
:Key cylinder
JSDIA1798ZZ
JSDIA1799ZZ
JSDIA1800ZZ
Revision: 2013 October
2014 JUKE
TM-318
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
TRANSMISSION RANGE SWITCH
TRANSMISSION RANGE SWITCH
Exploded View
INFOID:0000000009752663
Removal and Installation
INFOID:0000000009752664
REMOVAL
1.
Remove battery. Refer to
PG-99, "Removal and Installation"
2.
Remove transmission range switch connector.
3.
Remove control cable. Refer to
TM-311, "Removal and Installation"
.
4.
Remove transmission range switch from transaxle assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000009752665
ADJUSTMENT OF TRANSMISSION RANGE SWITCH
1.
Move selector lever to “N” position.
2.
Remove control cable from manual lever.
1.
Transmission range switch
2.
Transaxle assembly
: N·m (kg-m, in-lb)
JSDIA2397GB
Revision: 2013 October
2014 JUKE
TRANSMISSION RANGE SWITCH
TM-319
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Loosen mounting bolts (
) of transmission range switch. Insert
a pin (
φ
4 mm) into the adjusting holes (A) on both transmission
range switch and manual lever for adjusting the position.
4.
Tighten mounting bolts of transmission range switch.
5.
Connect control cable on manual lever. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing the CVT shift selector. Refer to
TM-226, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLAION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-226, "Inspection and Adjustment"
JSDIA2398ZZ
Revision: 2013 October
2014 JUKE
TM-320
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
TCM
TCM
Exploded View
INFOID:0000000009752666
Removal and Installation
INFOID:0000000009752667
CAUTION:
When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM. Refer to
TM-339, "2WD : Removal and Installation"
(AWD).
REMOVAL
1.
Remove the battery. Refer to
PG-99, "Removal and Installation"
2.
Remove air duct (inlet) and air cleaner case. Refer to
EM-25, "Removal and Installation"
.
3.
Disconnect the TCM connector.
4.
Remove the TCM.
5.
Remove the bracket.
INSTALLATION
Installation is the reverse order of removal.
Adjustment
INFOID:0000000009752668
ADJUSTMENT AFTER INSTALLATION
Perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to
.
1.
Bracket
2.
TCM
:Vehicle front
: N·m (kg-m, in-lb)
JSDIA2411GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст