Juke F15 (2012 year). Service Repair Manual — part 290
PCS
SYSTEM
PCS-7
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
NOTE:
BCM controls the starter relay.
RELAY CONTROL SYSTEM : Fail-Safe
INFOID:0000000006626136
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
Control relay
Input/output
Transmit unit
Control part
Reference page
• Headlamp low relay
• Headlamp high relay
• Low beam request signal
• High beam request signal
BCM (CAN)
• Headlamp (LO)
• Headlamp (HI)
Front fog lamp relay
Front fog light request signal
BCM (CAN)
Front fog lamp
Tail lamp relay
Position light request signal
BCM (CAN)
• Parking lamp
• License plate lamp
• Tail lamp
•
(without
DTRL)
•
(with
DTRL)
Illumination
• Front wiper relay
• Front wiper high relay
Front wiper request signal
BCM (CAN)
Front wiper motor
•
light & rain sen-
sor)
•
(without
light & rain sen-
sor)
Front wiper stop position sig-
nal
Front wiper motor
Rear window defogger
Rear window defogger switch
signal
BCM (CAN)
Rear window defogger
•
(with
AUTO A/C)
•
(without
AUTO A/C)
Horn relay
Theft warning horn request
signal
BCM (CAN)
Horn
• Starter relay
NOTE
• Starter control relay
Starter control relay signal
BCM (CAN)
Starter motor
Steering lock unit condition
signal
Steering lock unit
Starter relay control signal
Transmission range switch
Steering lock relay
Steering lock relay signal
BCM (CAN)
Steering lock unit
Steering lock unit condition
signal
Steering lock unit
CVT shift selector (Detention
switch) signal
CVT shift selector (Deten-
tion switch)
• Cooling fan relay-1
• Cooling fan relay-2
• Cooling fan relay-3
Cooling fan speed request
signal
ECM (CAN)
Cooling fan
•
(HR16DE)
•
(K9K)
A/C relay
A/C compressor request sig-
nal
ECM (CAN)
A/C compressor
(Magnet clutch)
Daytime running light re-
lay
• Daytime running light re-
quest signal
• Low beam request signal
BCM (CAN)
• Headlamp (LO)
• Parking lamp
• License plate lamp
• Tail lamp
Headlamp washer relay
Headlamp washer request
signal
BCM (CAN)
Headlamp washer
pump
Ignition relay
Ignition switch ON signal
BCM (CAN)
Each control unit, sen-
sor, actuator and relay
(Ignition power supply)
Vehicle speed signal (Meter)
Combination meter (CAN)
Push-button ignition switch
signal
Push-button ignition switch
PCS-8
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
SYSTEM
If No CAN Communication Is Available With ECM
If No CAN Communication Is Available With BCM
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
Control part
Fail-safe operation
Cooling fan
• For MR16DDT engine
- Transmits the pulse duty signal (PWM signal) 100% when the ignition switch is turned ON.
- Transmits the pulse duty signal (PWM signal) 0% when the ignition switch is turned OFF.
• Except for MR16DDT engine
- The cooling fan relay-1, the cooling fan relay-2 and the cooling fan relay-3 turn ON when the ignition switch
is turned ON (Cooling fan HI operation)
- The cooling fan relay-1, the cooling fan relay-2 and the cooling fan relay-3 turn OFF when the ignition
switch is turned OFF
A/C compressor
A/C relay OFF
Alternator
Outputs the power generation command signal (PWM signal) 0%
Control part
Fail-safe operation
Headlamp
• Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamp
• License plate lamp
• Illumination
• Tail lamp
• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
Front wiper motor
• The status just before activation of fail-safe control is maintained until the ignition switch is turned OFF while
the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe control is activated
while the front wiper is set in the INT mode and the front wiper motor is operating.
• Returns automatically wiper to stop position when ignition switch is turned ON if fail-safe control is activated
while front wiper motor is operated and wiper stop in the other position than stop position.
• The status is held at service position if the fail-safe control is activated while the service position function is
operating.
Front fog lamp
Front fog lamp relay OFF
Rear window defogger
Rear window defogger relay OFF
Horn
Horn OFF
Ignition relay
The status just before activation of fail-safe is maintained.
Starter motor
Starter control relay OFF
Steering lock unit
Steering lock relay OFF
Voltage judgment
IPDM E/R judgment
Operation
Ignition relay contact
side
Ignition relay excitation
coil side
ON
ON
Ignition relay ON normal
—
OFF
OFF
Ignition relay OFF normal
—
ON
OFF
Ignition relay ON stuck
• Detects DTC “B2098: IGN RELAY ON”
• Turns ON the tail lamp relay for 10 minutes
OFF
ON
Ignition relay OFF stuck
Detects DTC “B2099: IGN RELAY OFF”
PCS
SYSTEM
PCS-9
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
POWER CONTROL SYSTEM
POWER CONTROL SYSTEM : System Diagram
INFOID:0000000006626154
POWER CONTROL SYSTEM : System Description
INFOID:0000000006626155
COOLING FAN CONTROL (ONLY FOR MODELS WITH MR16DDT ENGINE)
IPDM E/R outputs pulse duty signal (PWM signal) to the cooling fan control module according to the status of
the cooling fan speed request signal received from ECM via CAN communication. Refer to
NOTE:
After ignition switch OFF, IPDM E/R turn the cooling fan relay ON and outputs pulse duty signal (PWM signal)
to the cooling fan control module according to the request signal from ECM for cooling the engine according to
the situation.
ALTERNATOR CONTROL
IPDM E/R outputs power generation command signal (PWM signal) to the alternator according to the status of
the power generation command value signal received from ECM via CAN communication. Refer to
"POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM : System Diagram (Gasoline Engine
Models)"
SIGNAL BUFFER SYSTEM
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
JSMIA0004GB
PCS-10
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
SYSTEM
SIGNAL BUFFER SYSTEM : System Diagram
INFOID:0000000006597898
SIGNAL BUFFER SYSTEM : System Description
INFOID:0000000006597899
• NOTE:
Only for K9K engine models
IPDM E/R reads the status of the oil pressure switch and transmits the oil pressure switch signal to BCM via
CAN communication. Refer to
MWI-12, "OIL PRESSURE WARNING LAMP : System Diagram"
• IPDM E/R reads the status of the hood switch and transmits the hood switch signal to BCM via CAN commu-
SEC-20, "VEHICLE SECURITY SYSTEM : System Diagram"
• IPDM E/R receives the rear window defogger control signal from BCM via CAN communication and trans-
mits the rear window defogger status signal to ECM and multi display unit via CAN communication. Refer to
DEF-7, "WITH AUTO A/C : System Diagram"
(with AUTO A/C) or
DEF-7, "WITHOUT AUTO A/C : System
POWER CONSUMPTION CONTROL SYSTEM
POWER CONSUMPTION CONTROL SYSTEM : System Diagram
INFOID:0000000006634105
POWER CONSUMPTION CONTROL SYSTEM : System Description
INFOID:0000000006597901
OUTLINE
• IPDM E/R incorporates a power consumption control function that reduces the power consumption accord-
ing to the vehicle status.
• IPDM E/R changes its status (control mode) with the sleep wake up signal received from BCM via CAN com-
munication.
JMMIA0571GB
JMMIA0579GB
PCS
SYSTEM
PCS-11
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Normal mode (wake-up)
- CAN communication is normally performed with other control units.
- Individual unit control by IPDM E/R is normally performed.
Low power consumption mode (sleep)
- Low power consumption control is active.
- CAN transmission is stopped.
SLEEP MODE ACTIVATION
• IPDM E/R judges that the sleep-ready conditions are fulfilled when the ignition switch is OFF and none of the
conditions below are present. Then it transmits a sleep-ready signal (ready) to BCM via CAN communica-
tion.
- Outputting signals to actuators
- Switches or relays operating
- Output requests are being received from control units via CAN communication.
• IPDM E/R stops CAN communication and enters the low power consumption mode when it receives a sleep
wake up signal (sleep) from BCM and the sleep-ready conditions are fulfilled.
WAKE-UP OPERATION
• IPDM E/R changes from the low power consumption mode to the normal mode when it receives a sleep
wake-up signal (wake up) from BCM or any of the following conditions is fulfilled. In addition, it transmits a
sleep-ready signal (not-ready) to BCM via CAN communication to report the CAN communication start.
- Ignition switch ON
- An output request is received from a control unit via CAN communication.
PCS-12
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000006597902
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp (only for K9K engine models)
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with food when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4.
Oil pressure warning lamp starts blinking when the auto active test starts*. (only for K9K engine models)
*: Except for K9K engine models, oil pressure warning lamp turn ON when auto active test start.
5.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
(with super lock) or
DLK-258, "Component Function Check"
(without super
lock).
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Oil pressure warning lamp
Blinks continuously during operation of auto active test
NOTE:
Except for K9K engine models, turn ON continuously during operation of auto active
test.
2
Rear window defogger
10 seconds
3
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
4
• Parking lamp
• License plate lamp
• Tail lamp
• Front fog lamp
10 seconds
5
Headlamp
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-13
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Concept of auto active test
*: Only for models with MR16DDT engine
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
6
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
7
Cooling fan
• LO for 5 seconds
→
HI for 5 seconds (Except for MR16DDT models)
• 50% duty for 5 seconds
→
100% duty for 5 seconds (For MR16DDT models)
Operation
sequence
Inspection location
Operation
JMMIA0564GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger ground
circuit
• Harness or connector between
IPDM E/R and rear window de-
fogger
• IPDM E/R
Any of the following components do not operate
• Parking lamp
• License plate lamp
• Tail lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between
IPDM E/R and applicable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal be-
tween A/C amp. and ECM
• CAN communication signal be-
tween ECM and IPDM E/R
NO
• Magnet clutch
• Harness or connector between
IPDM E/R and magnet clutch
• IPDM E/R
PCS-14
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT-III Function (IPDM E/R)
INFOID:0000000006597903
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
Monitor item
Oil pressure warning lamp does not operate
(only for K9K engine models)
Perform auto active test.
Does the oil pressure warning
lamp blink?
YES
• Harness or connector between
IPDM E/R and oil pressure
switch
• Oil pressure switch
• IPDM E/R
NO
• CAN communication signal be-
tween IPDM E/R and BCM
• CAN communication signal be-
tween BCM and combination
meter
• Combination meter
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal be-
tween ECM and IPDM E/R
NO
• Harness or connector between
IPDM E/R and cooling fan motor
• Harness or connector between
IPDM E/R and cooling fan con-
trol module.
(Only for models with MR16DDT
engine)
• Harness or connector between
cooling fan control module and
cooling fan motor
(Only for models with MR16DDT
engine)
• Cooling fan motor
• Cooling fan control module
(Only for models with MR16DDT
engine)
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-15
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Monitor Item
[Unit]
MAIN
SIGNALS
Description
RAD FAN REQ
[%]
×
Displays the value of the cooling fan speed request signal received from ECM via CAN
communication.
NOTE:
This item is displayed only for vehicle with MR16DDT engine.
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed request signal received from ECM via CAN
communication.
NOTE:
This item is displayed only for vehicle without MR16DDT engine.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via CAN
communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN com-
munication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN com-
munication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via CAN
communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN com-
munication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the ignition power supply (M/T models) or shift position (CVT
models) judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN com-
munication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN com-
munication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]
Displays the status of the starter relay and starter control relay judged by IPDM E/R.
DETENT SW
[Off/On]
Displays the status of the CVT shift selector (detention switch) judged by IPDM E/R.
S/L RLY -REQ
[Off/On]
Displays the status of the steering lock relay signal received from BCM via CAN com-
munication.
S/L STATE
[LOCK/UNLK/UNKWN]
Displays the status of the steering lock judged by IPDM E/R.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM via
CAN communication.
OIL P SW
[Open/Close]
Displays the status of the oil pressure switch judged by IPDM E/R.
NOTE:
This item is monitored only K9K engine models.
HOOD SW
[Off/On]
Displays the status of the hood switch judged by IPDM E/R.
PCS-16
< SYSTEM DESCRIPTION >
[IPDM E/R (WITH I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
Test item
HL WASHER REQ
[Off/On]
Displays the status of the headlamp washer request signal received from BCM via
CAN communication.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM via
CAN communication.
HORN CHIRP
[Off/On]
NOTE:
The item is indicated, but not monitored.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
REAR DEFOGGER
Off
OFF
On
Operates the rear window defogger relay.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
For MR16DDT engine
1
OFF
2
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control
module.
3
Transmits 75% pulse duty signal (PWM signal) to the cooling fan control
module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control
module.
Except for MR16DDT
engine
1
OFF
2
Operates the cooling fan relay (LO operation).
3
Operates the cooling fan relay (HI operation).
4
HEAD LAMP WASHER
On
Operates the headlamp washer relay for 1 second.
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1
second intervals.
Fog
Operates the front fog lamp relay.
PCS
IPDM E/R
PCS-17
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECU DIAGNOSIS INFORMATION
IPDM E/R
Reference Value
INFOID:0000000006597904
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition
Value/Status
RAD FAN REQ
NOTE:
This item is displayed only for
vehicle with MR16DDT en-
gine.
Engine idle speed
Changes depending on engine
coolant temperature, air conditioner
operation status, vehicle speed,
etc.
0 – 100%
MOTOR FAN REQ
NOTE:
This item is displayed only for
vehicle without MR16DDT
engine.
Engine idle speed
Changes depending on engine
coolant temperature, air conditioner
operation status, vehicle speed,
etc.
1/2/3/4
AC COMP REQ
Engine running
A/C switch OFF
Off
A/C switch ON
(Compressor is operating)
On
TAIL&CLR REQ
Lighting switch OFF
Off
• Lighting switch 1ST, 2ND or AUTO (Light is illuminated)
• Daytime running light system operated
On
HL LO REQ
Lighting switch OFF
Off
Lighting switch 2ND or AUTO (Light is illuminated)
On
HL HI REQ
Lighting switch 2ND or AUTO (light
is illuminated)
Lighting switch other than HI and
PASS
Off
Lighting switch HI or PASS
On
FR FOG REQ
Lighting switch 1ST, 2ND or
AUTO (Light is illuminated)
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
FR WIP REQ
Ignition switch ON
Front wiper switch OFF
Stop
Front wiper switch INT
1LOW
Front wiper switch LO
Low
Front wiper switch HI
Hi
WIP AUTO STOP
Ignition switch ON
Front wiper stop position
STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT
Ignition switch ON
Front wiper operates normally.
Off
Front wiper stops at fail-safe opera-
tion.
BLOCK
IGN RLY1 -REQ
Ignition switch OFF or ACC
Off
Ignition switch ON
On
IGN RLY
Ignition switch OFF or ACC
Off
Ignition switch ON
On
PUSH SW
Release the push-button ignition switch
Off
Press the push-button ignition switch
On
PCS-18
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITH I-KEY)]
IPDM E/R
INTER/NP SW
Ignition switch ON (CVT models)
Selector lever in any position other
than P or N
Off
Selector lever in P or N position
On
Ignition switch OFF or ACC (M/T models)
Off
Ignition switch ON (M/T models)
On
ST RLY CONT
Ignition switch ON
Off
At engine cranking
On
IHBT RLY -REQ
Ignition switch ON
Off
At engine cranking
On
ST/INHI RLY
Ignition switch ON
Off
At engine cranking
INHI ON
→
ST ON
The status of starter relay or starter control relay cannot be recognized by
the battery voltage malfunction, etc. when the starter relay is ON and the
starter control relay is OFF.
UNKWN
DETENT SW
Ignition switch ON
• Press the selector button with se-
lector lever in P position.
• Selector lever in any position oth-
er than P.
Off
Release the selector button with selector lever in P position.
NOTE:
Status fixed to On for M/T models
On
S/L RLY -REQ
None of the conditions below are present.
Off
• Open the driver door after the ignition switch is turned OFF (for a few
seconds).
• Press the push-button ignition switch when the steering lock is activat-
ed.
On
S/L STATE
Steering lock is locked.
LOCK
Steering lock is unlocked.
UNLK
[DTC: B210A] is detected.
UNKWN
DTRL REQ
Daytime running light system is not operated with ignition switch OFF
Off
Any of the condition below
• Daytime running light system is operated
• Light switch 2ND or AUTO (light is illuminated)
On
OIL P SW
NOTE:
This item is monitored only
for vehicle with K9K engine.
Ignition switch OFF, ACC or engine running
Open
Ignition switch ON
Close
HOOD SW
Close the hood
Off
Open the hood
On
HL WASHER REQ
Not operating
Off
Headlamp washer operating
On
THFT HRN REQ
Not operation
Off
Theft warning alarm is activated
On
HORN CHIRP
NOTE:
The item is indicated, but not monitored.
Off
Monitor Item
Condition
Value/Status
PCS
IPDM E/R
PCS-19
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TERMINAL LAYOUT
PHYSICAL VALUES
JPMIA1423ZZ
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
1
(R)
Ground
Battery power supply
Input
Ignition switch OFF
6 – 16 V
2
(G)
Ground
Battery power supply
Input
Ignition switch OFF
6 – 16 V
3
(R)
Ground
Starter motor
Output
Other than engine cranking
0 – 1 V
At engine cranking
6 – 16 V
4
(P)
Ground
Battery power supply
Input
Ignition switch OFF
9 – 16 V
5*
2
(LG)
Ground
Cooling fan relay-1
power supply
Output
Cooling fan OFF
0 – 1 V
Cooling fan operated
9 – 16 V
7*
2
(Y)
Ground
Cooling fan relay-2
power supply
Output
Cooling fan OFF
0 – 1 V
Cooling fan LO operated
4 – 8 V
Cooling fan HI operated
9 – 16 V
8
(V)
Ground
Battery power supply
Input
Ignition switch OFF
6 – 16 V
9
(B/Y)
Ground
Ground
—
Ignition switch ON
0 – 1 V
10*
2
(L)
Ground
Cooling fan motor
ground
Output
Cooling fan OFF
0 – 1 V
Cooling fan LO operated
4 – 8 V
Cooling fan HI operated
9 – 16 V
PCS-20
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITH I-KEY)]
IPDM E/R
14
(R)
Ground
Rear window defogger
Output
Ignition
switch
ON
Rear window defogger switch
OFF
0 – 1 V
Rear window defogger switch
ON
9 – 16 V
18
(B/Y)
Ground
Ground
—
Ignition switch ON
0 – 1 V
19
(W)
Ground
Front fog lamp (RH)
Output
Lighting
switch
1ST, 2ND
or AUTO
Front fog lamp switch OFF
0 – 1 V
Front fog lamp switch ON
9 – 16 V
20
(V)
Ground
Front fog lamp (LH)
Output
Lighting
switch
1ST, 2ND
or AUTO
Front fog lamp switch OFF
0 – 1 V
Front fog lamp switch ON
9 – 16 V
21
(Y)
Ground
Headlamp washer re-
lay control
Output
Ignition
switch
ON
Headlamp washer deactivated
9 – 16 V
Headlamp washer activated
0 – 1 V
23
(SB)
Ground
Cranking request
Output
Ignition switch OFF
0 – 1 V
Ignition
switch
ON
Select lever P or N
Select lever in any position oth-
er than P or N
9 – 16 V
Engine running
24*
7
(R)
Ground
Oil pressure switch
Input
Ignition
switch
ON
Engine stopped
0 – 1 V
Engine running
9 – 16 V
25
(BR)
Ground
Front wiper stop posi-
tion
Input
Ignition
switch
ON
Front wiper stop position
0 – 1.5 V
Any position other than front
wiper stop position
9 – 16 V
26
(P)
Ground
CAN-L
Input/
Output
—
—
27
(L)
Ground
CAN-H
Input/
Output
—
—
28
(Y)
Ground
Daytime running light
relay control
Output
Daytime running light deactivated
9 – 16 V
Daytime running light activated
0 – 1 V
30
(V)
Ground
Starter relay control
Output
Ignition
switch
ON
Select lever P or N
6 – 16 V
Select lever in any position oth-
er than P or N
0 – 1 V
31
(Y)
Ground
Fuel pump relay con-
trol
Output
• Approximately 1 second after turning the
ignition switch ON
• Engine running
0 – 1 V
Approximately 1 second or more after turn-
ing the ignition switch ON
6 – 16 V
32
(SB)
Ground
Hood switch
Input
Close the hood
9 – 16 V
Open the hood
0 – 1 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
PCS
IPDM E/R
PCS-21
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITH I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
33
(G)
Ground
Power generation
command signal
Output
Ignition switch ON
6.3 V
40% is set on “ACTIVE TEST”, “ALTERNA-
TOR DUTY” of “ENGINE”
3.8 V
80% is set on “ACTIVE TEST”, “ALTERNA-
TOR DUTY” of “ENGINE”
1.4 V
34
(L)
Ground
Horn relay control
Output
The horn is deactivated
9 – 16 V
The horn is activated
0 – 1 V
35
(G)
Ground
ECM relay power sup-
ply
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
0 – 1 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
6 – 16 V
36
(P)
Ground
ECM relay power sup-
ply
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
0 – 1 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
6 – 16 V
37
(L)
Ground
Parking lamp
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
9 – 16 V
38
(R)
Ground
Rear combination
lamp RH
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
9 – 16 V
39
(L)
Ground
Front wiper HI
Output
Ignition
switch
ON
Front wiper switch OFF
0 – 1 V
Front wiper switch HI
9 – 16 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
JPMIA0001GB
JPMIA0002GB
JPMIA0003GB
PCS-22
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITH I-KEY)]
IPDM E/R
41
(BR)
Ground
ECM relay control
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
6 – 16 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
0 – 1 V
42
(Y)
Ground
ECM power supply
Output
Ignition switch OFF
6 – 16 V
43
(V)*
5
(R)*
6
Ground
Illuminations
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
9 – 16 V
44
(GR)
Ground
Rear combination
lamp LH
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
9 – 16 V
45
(W)
Ground
Front wiper LO
Output
Ignition
switch
ON
Front wiper switch OFF
0 – 1 V
Front wiper switch LO
9 – 16 V
46
(LG)
Ground
Steering lock unit pow-
er supply
Output
Ignition switch ACC or ON
0 – 1 V
Ignition
switch
OFF
A few seconds after opening
the driver door
9 – 16 V
Ignition
switch
LOCK
Press the push-button ignition
switch
9 – 16 V
47
(V)
Ground
Alternator input
Input
Ignition switch OFF or ACC
0 – 1 V
Ignition switch ON
48
(BR)
Ground
Transmission range
switch
*3
Input
Select lever in any position other than P or
N (Ignition switch ON)
0 – 1 V
Select lever P or N (Ignition switch ON)
9 – 16 V
Ignition relay power
supply
*4
Ignition switch OFF
0 – 1 V
Ignition switch ON
9 – 16 V
49
(Y)
Ground
Headlamp HI (RH)
Output
Ignition
switch
2ND or
AUTO
Lighting switch OFF
0 – 1 V
• Lighting switch HI
• Lighting switch PASS
9 – 16 V
50
(G)
Ground
Headlamp HI (LH)
Output
Ignition
switch
2ND or
AUTO
Lighting switch OFF
0 – 1 V
• Lighting switch HI
• Lighting switch PASS
9 – 16 V
51
(L)
Ground
Headlamp LO (LH)
Output
Lighting switch OFF
0 – 1 V
Lighting switch 2ND
9 – 16 V
52
(P)
Ground
Headlamp LO (RH)
Output
Lighting switch OFF
0 – 1 V
Lighting switch 2ND
9 – 16 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
JMMIA0260GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст