Juke F15 (2012 year). Service Repair Manual — part 364
TM-256
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10B]
SHIFT LOCK SYSTEM
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHCK GROUND CIRCUIT
Check the continuity between the CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK PART POSITION SWITCH
1.
Disconnect park position switch connector.
2.
Check park position switch. Refer to
TM-257, "Component Inspection (Park Position Switch)"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts.
7.
CHECK SHIFT LOCK SOLENOID
1.
Disconnect shift lock solenoid connector.
2.
Check shift lock solenoid. Refer to
TM-257, "Component Inspection (Shift Lock Solenoid)"
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace the malfunctioning parts.
8.
CHECK CVT SHIFT SELECTOR HARNESS
Check CVT shift selector harness. Refer to
TM-257, "Component Inspection (CVT Shift Selector Harness)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning parts.
9.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to
"Wiring Diagram - IGNITION POWER SUPPLY -"
.
• Ignition switch
• 10A fuse [No.3, fuse block (J/B)]. Refer to
PG-22, "Fuse, Connector and Terminal Arrangement"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning parts.
10.
CHECK INSTALLATION POSITION OF STOP LAMP SWITCH
Adjust stop lamp switch position. Refer to
BR-9, "Inspection and Adjustment"
(RHD).
>> GO TO 11.
Stop lamp switch harness
connector
Ground
Continuity
Connector
Terminal
E102
4
Ground
Not existed
CVT shift selector harness
connector
Ground
Continuity
Connector
Terminal
M57
4
Ground
Existed
SHIFT LOCK SYSTEM
TM-257
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
11.
CHECK STOP LAMP SWITCH (PART 2)
Check stop lamp switch. Refer to
TM-258, "Component Inspection (Stop Lamp Switch)"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the malfunctioning parts.
Component Inspection (Shift Lock Solenoid)
INFOID:0000000006601677
1.
CHECK SHIFT LOCK SOLENOID
Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.
CAUTION:
• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the shift lock unit. Refer to
TM-271, "Disassembly and Assembly"
Component Inspection (Park Position Switch)
INFOID:0000000006752450
1.
CHECK PARK POSITION SWITCH
Check the continuity between park position switch connector terminals.
CAUTION:
• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the park position switch. Refer to
TM-271, "Disassembly and Assembly"
Component Inspection (CVT Shift Selector Harness)
INFOID:0000000006752451
1.
CHECK CVT SHIFT SELECTOR HARNESS (PART 1)
Check the continuity between the CVT shift selector harness connector terminal and the shift lock solenoid
harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the CVT shift selector harness. Refer to
TM-271, "Disassembly and Assembly"
.
Shift lock solenoid connector
Condition
Status
Terminal
+ (fuse)
−
1
2
Apply battery voltage be-
tween terminals 1 and 2.
Shift lock solenoid operates
Park position switch connector
Condition
Continuity
Terminal
1
2
Shift the selector lever to “P” position.
Existed
Other than above
Not existed
CVT shift selector harness
connector
Shift lock solenoid harness
connector
Continuity
Connector
Terminal
Connector
Terminal
M324
5
M326
1
Existed
TM-258
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10B]
SHIFT LOCK SYSTEM
2.
CHECK CVT SHIFT SELECTOR HARNESS (PART 2)
Check the continuity between the shift lock solenoid harness connector terminal and the park position switch
harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the CVT shift selector harness. Refer to
TM-271, "Disassembly and Assembly"
.
3.
CHECK CVT SHIFT SELECTOR HARNESS (PART 3)
Check the continuity between the park switch harness connector terminal and the CVT shift selector harness
connector terminal.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the CVT shift selector harness. Refer to
TM-271, "Disassembly and Assembly"
.
4.
CHECK CVT SHIFT SELECTOR HARNESS (PART 4)
Check harness cladding CVT shift selector harness for damage.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the CVT shift selector harness. Refer to
TM-271, "Disassembly and Assembly"
.
Component Inspection (Stop Lamp Switch)
INFOID:0000000006601676
1.
CHECK STOP LAMP SWITCH
Check the continuity between the stop lamp switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
BR-21, "Removal and Installation"
(RHD).
Shift lock solenoid harness
connector
Park position switch harness
connector
Continuity
Connector
Terminal
Connector
Terminal
M326
2
M325
1
Existed
Park switch harness connector
CVT shift selector harness
connector
Continuity
Connector
Terminal
Connector
Terminal
M325
2
M324
6
Existed
Stop lamp switch connector
Condition
Continuity
Terminal
3
4
Depressed brake pedal
Existed
Released brake pedal
Not existed
SYSTEM SYMPTOM
TM-259
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SYMPTOM DIAGNOSIS
SYSTEM SYMPTOM
Symptom Table
INFOID:0000000006601683
The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.
No.
Item
Symptom
Condition
Diagnostic Item
Reference
1
Shift Shock
Large shock. (“N”
→
“D” position)
ON vehicle
1. Engine idle speed
2. Engine speed signal
3. Accelerator pedal position sensor
4. CVT position
5. CVT fluid temperature sensor
6. CAN communication line
7. CVT fluid level and state
8. Line pressure test
9. Torque converter clutch solenoid valve
10. Lock-up select solenoid valve
11. Transmission range switch
12. Control valve
OFF vehicle
13. Forward clutch
2
Shift Shock
Large shock. (“N”
→
“R” position)
ON vehicle
1. Engine idle speed
2. Engine speed signal
3. Accelerator pedal position sensor
4. CVT position
5. CVT fluid temperature sensor
6. CAN communication line
7. CVT fluid level and state
8. Line pressure test
9. Torque converter clutch solenoid valve
10. Lock-up select solenoid valve
11. Transmission range switch
12. Control valve
OFF vehicle
13. Reverse brake
3
Shift Shock
Shock is too large for
lock-up.
ON vehicle
1. CVT position
2. Engine speed signal
3. CAN communication line
4. CVT fluid level and state
5. Control valve
OFF vehicle
6. Torque converter
TM-260
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
SYSTEM SYMPTOM
4
Slips/Will
Not Engage
Vehicle cannot be
started from “D” posi-
tion.
ON vehicle
1. CVT fluid level and state
2. CVT position
3. CAN communication line
4. Line pressure test
5. Stall test
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Accelerator pedal position sensor
10. CVT fluid temperature sensor
11. Secondary pressure sensor
12. Power supply
13. Control valve
OFF vehicle
14. Oil pump assembly
15. Forward clutch
16. Parking components
5
Vehicle cannot be
started from “R” posi-
tion.
ON vehicle
1. CVT fluid level and state
2. CVT position
3. CAN communication line
4. Line pressure test
5. Stall test
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Accelerator pedal position sensor
10. CVT fluid temperature sensor
11. Secondary pressure sensor
12. Power supply
13. Control valve
OFF vehicle
14. Oil pump assembly
15. Reverse brake
16. Parking components
No.
Item
Symptom
Condition
Diagnostic Item
Reference
SYSTEM SYMPTOM
TM-261
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6
Slips/Will
Not Engage
Does not lock-up.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Engine speed signal
4. Primary speed sensor
5. Torque converter clutch solenoid valve
6. CAN communication line
7. Stall test
8. Step motor
9. Transmission range switch
10. Lock-up select solenoid valve
11. CVT fluid temperature sensor
12. Secondary speed sensor
13. Secondary pressure sensor
14. Control valve
OFF vehicle
15. Torque converter
16. Oil pump assembly
7
Does not hold lock-up
condition.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Engine speed signal
4. Primary speed sensor
5. Torque converter clutch solenoid valve
6. CAN communication line
7. Stall test
8. Step motor
9. Transmission range switch
10. Lock-up select solenoid valve
11. CVT fluid temperature sensor
12. Secondary speed sensor
13. Secondary pressure sensor
14. Control valve
OFF vehicle
15. Torque converter
16. Oil pump assembly
No.
Item
Symptom
Condition
Diagnostic Item
Reference
TM-262
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
SYSTEM SYMPTOM
8
Slips/Will
Not Engage
Lock-up is not re-
leased.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Engine speed signal
4. Primary speed sensor
5. Torque converter clutch solenoid valve
6. CAN communication line
7. Stall test
8. Control valve
OFF vehicle
9. Torque converter
10. Oil pump assembly
9
With selector lever in
“D” position, accelera-
tion is extremely poor.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Stall test
4. Accelerator pedal position sensor
5. CAN communication line
6. Transmission range switch
7. CVT position
8. Step motor
9. Primary speed sensor
10. Secondary speed sensor
11. Accelerator pedal position sensor
12. Secondary pressure sensor
13. CVT fluid temperature sensor
14. Power supply
15. Control valve
OFF vehicle
16. Torque converter
17. Oil pump assembly
18. Forward clutch
No.
Item
Symptom
Condition
Diagnostic Item
Reference
SYSTEM SYMPTOM
TM-263
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10
Slips/Will
Not Engage
With selector lever in
“R” position, accelera-
tion is extremely poor.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Stall test
4. Accelerator pedal position sensor
5. CAN communication line
6. Transmission range switch
7. CVT position
8. Step motor
9. Primary speed sensor
10. Secondary speed sensor
11. Accelerator pedal position sensor
12. Secondary pressure sensor
13. CVT fluid temperature sensor
14. Power supply
15. Control valve
OFF vehicle
16. Torque converter
17. Oil pump assembly
18. Reverse brake
11
Slips at lock-up.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Engine speed signal
4. Primary speed sensor
5. Torque converter clutch solenoid valve
6. CAN communication line
7. Stall test
8. Step motor
9. Transmission range switch
10. Lock-up select solenoid valve
11. CVT fluid temperature sensor
12. Secondary speed sensor
13. Secondary pressure sensor
14. Control valve
OFF vehicle
15. Torque converter
16. Oil pump assembly
No.
Item
Symptom
Condition
Diagnostic Item
Reference
TM-264
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
SYSTEM SYMPTOM
12
Other
No creep at all.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Accelerator pedal position sensor
4. Transmission range switch
5. CAN communication line
6. Stall test
7. CVT position
8. Step motor
9. Primary speed sensor
10. Secondary speed sensor
11. Accelerator pedal position sensor
12. CVT fluid temperature sensor
13. Secondary pressure sensor
14. Power supply
15. Control valve
OFF vehicle
16. Torque converter
17. Oil pump assembly
18. Gear system
19. Forward clutch
20. Reverse brake
13
Vehicle cannot run in
all positions.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Transmission range switch
4. Stall test
5. CVT position
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Accelerator pedal position sensor
10. CVT fluid temperature sensor
11. Secondary pressure sensor
12. Power supply
13. Control valve
OFF vehicle
14. Torque converter
15. Oil pump assembly
16. Gear system
17. Forward clutch
18. Reverse brake
19. Parking components
No.
Item
Symptom
Condition
Diagnostic Item
Reference
SYSTEM SYMPTOM
TM-265
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
14
Other
With selector lever in
“D” position, driving is
not possible.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Transmission range switch
4. Stall test
5. CVT position
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Accelerator pedal position sensor
10. CVT fluid temperature sensor
11. Secondary pressure sensor
12. Power supply
13. Control valve
OFF vehicle
14. Torque converter
15. Oil pump assembly
16. Gear system
17. Forward clutch
18. Parking components
15
With selector lever in
“R” position, driving is
not possible.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Transmission range switch
4. Stall test
5. CVT position
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Accelerator pedal position sensor
10. CVT fluid temperature sensor
11. Secondary pressure sensor
12. Power supply
13. Control valve
OFF vehicle
14. Torque converter
15 Oil pump assembly
16. Gear system
17. Reverse brake
18. Parking components
No.
Item
Symptom
Condition
Diagnostic Item
Reference
TM-266
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
SYSTEM SYMPTOM
16
Other
Judder occurs during
lock-up.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. Primary speed sensor
4. Secondary speed sensor
5. Accelerator pedal position sensor
6. CAN communication line
7. Torque converter clutch solenoid valve
8. Control valve
OFF vehicle
9. Torque converter
17
Strange noise in “D”
position.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. CAN communication line
4. Control valve
OFF vehicle
5. Torque converter
6. Oil pump assembly
7. Gear system
8. Forward clutch
9. Bearing
18
Strange noise in “R”
position.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. CAN communication line
4. Control valve
OFF vehicle
5. Torque converter
6. Oil pump assembly
7. Gear system
8. Reverse brake
19
Strange noise in “N”
position.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. CAN communication line
4. Control valve
OFF vehicle
5. Torque converter
6. Oil pump assembly
7. Gear system
No.
Item
Symptom
Condition
Diagnostic Item
Reference
SYSTEM SYMPTOM
TM-267
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
20
Other
Vehicle does not de-
celerate by engine
brake.
ON vehicle
1. CVT fluid level and state
2. CVT position
3. CAN communication line
4. Step motor
5. Primary speed sensor
6. Secondary speed sensor
7. Line pressure test
8. Engine speed signal
9. Accelerator pedal position sensor
10. Control valve
21
Maximum speed low.
ON vehicle
1. CVT fluid level and state
2. Line pressure test
3. Accelerator pedal position sensor
4. CAN communication line
5. Stall test
6. Step motor
7. Primary speed sensor
8. Secondary speed sensor
9. Secondary pressure sensor
10. CVT fluid temperature sensor
11. Control valve
OFF vehicle
12. Torque converter
13. Oil pump assembly
14. Gear system
15. Forward clutch
22
With selector lever in
“P” position, vehicle
does not enter park-
ing condition or, with
selector lever in an-
other position, park-
ing condition is not
cancelled.
ON vehicle
1. Transmission range switch
2. CVT position
OFF vehicle
3. Parking components
23
Vehicle runs with CVT
in “P” position.
ON vehicle
1. Transmission range switch
2. CVT fluid level and state
3. CVT position
4. Control valve
OFF vehicle
5. Parking components
6. Gear system
No.
Item
Symptom
Condition
Diagnostic Item
Reference
TM-268
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
SYSTEM SYMPTOM
24
Other
Vehicle runs with CVT
in “N” position.
ON vehicle
1. Transmission range switch
2. CVT fluid level and state
3. CVT position
4. Control valve
OFF vehicle
5. Gear system
6. Forward clutch
7. Reverse brake
25
Engine stall.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. Primary speed sensor
4. Torque converter clutch solenoid valve
5. CAN communication line
6. Stall test
7. Secondary pressure sensor
8. Control valve
OFF vehicle
9. Torque converter
26
Engine stalls when
selector lever shifted
“N”
→
“D”or “R”.
ON vehicle
1. CVT fluid level and state
2. Engine speed signal
3. Primary speed sensor
4. Torque converter clutch solenoid valve
5. CAN communication line
6. Stall test
7. Control valve
OFF vehicle
8. Torque converter
27
Engine speed does
not return to idle.
ON vehicle
1. CVT fluid level and state
2. Accelerator pedal position sensor
3. Secondary speed sensor
4. CAN communication line
5. Control valve
No.
Item
Symptom
Condition
Diagnostic Item
Reference
SYSTEM SYMPTOM
TM-269
< SYMPTOM DIAGNOSIS >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
28
Other
CVT does not shift
ON vehicle
1. CVT fluid level and state
2. CVT position
3. Line pressure test
4. Engine speed signal
5. Accelerator pedal position sensor
6. CAN communication line
7. Primary speed sensor
8. Secondary speed sensor
9. Step motor
10. Control valve
OFF vehicle
11. Oil pump assembly
29
Engine does not start
in “N” or “P” position.
ON vehicle
1. Ignition switch and starter
2. CVT position
3. Transmission range switch
30
Engine starts in posi-
tions other than “N” or
“P”.
ON vehicle
1. Ignition switch and starter
2. CVT position
3. Transmission range switch
31
When brake pedal is
depressed with igni-
tion switch ON, selec-
tor lever cannot be
shifted from “P” posi-
tion to other position.
ON vehicle
1. Stop lamp switch
2. Shift lock solenoid
3. CVT shift selector
32
When brake pedal is
not depressed with ig-
nition switch ON, se-
lector lever can be
shifted from “P” posi-
tion to other position.
ON vehicle
1. Stop lamp switch
2. Shift lock solenoid
3. CVT shift selector
33
Cannot be changed to
manual mode.
ON vehicle
1. Manual mode switch
2. CAN communication line
3. Combination meters
34
CVT indicator lamp
does not come on.
ON vehicle
1. CAN communication line
2. Combination meters
3. TCM power supply and ground
No.
Item
Symptom
Condition
Diagnostic Item
Reference
TM-270
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CVT SHIFT SELECTOR
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000006601958
Removal and Installation
INFOID:0000000006601959
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Disconnect battery cable from negative terminal. Refer to
PG-124, "Removal and Installation"
.
2.
Shift the selector lever to “N” position.
3.
Remove the center console. Refer to
IP-23, "Removal and Installation"
.
4.
Disconnect the CVT shift selector connector.
5.
Shift the selector lever to “P” position.
6.
Remove the key interlock cable from the CVT shift selector assembly. Refer to
(Without push stater system).
7.
Remove the control cable from the CVT shift selector assembly. Refer to
TM-273, "Removal and Installa-
8.
Remove the CVT shift selector assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Selector lever knob
2.
Lock pin
3.
Knob cover
4
Position indication panel
5.
CVT shift selector assembly
6.
CVT shift lock unit
7.
Key interlock rod*
8.
Indicator lamp
:N·m (kg-m, it-lb)
*: Without push engine starter
JSDIA1871GB
CVT SHIFT SELECTOR
TM-271
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and insert
the control cable until it stops.
Disassembly and Assembly
INFOID:0000000006601960
DISASSEMBLY
1.
Slide the selector lever knob cover (1) down.
CAUTION:
Never damage the knob cover.
2.
Pull out the lock pin (2).
3.
Pull the selector lever knob (3) and knob cover upwards to
remove them.
4.
Remove the position lamp.
5.
Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the CVT shift selector
assembly (2).
CAUTION:
Never damage the CVT shift selector assembly.
6.
Shift the selector lever to “N” position.
7.
Remove the shift lock unit from the CVT shift selector assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Follow the procedure below and place the selector knob onto the CVT shift selector.
JSDIA1624ZZ
JSDIA1796ZZ
JSDIA1802ZZ
JSDIA1804ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст