Nissan Pathfinder. Manual — part 1184
TCM
TM-195
< REMOVAL AND INSTALLATION >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
TCM
Exploded View
INFOID:0000000009177653
Removal and Installation
INFOID:0000000009177654
CAUTION:
• To replace TCM, perform " WRITE IP CHARA – REPLACEMENT TCM" of the CONSULT Work Support
before removing TCM and save TCM data in CONSULT. Refer to
• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-
FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before start the operation.
REMOVAL
1. Remove the front air duct. Refer to
2. Disconnect the negative battery terminal. Refer to
PG-90, "Removal and Installation"
3. Disconnect the TCM harness connector.
4. Remove the TCM and bracket as a set.
5. Remove the TCM from the bracket.
INSTALLATION
Installation is the reverse order of removal.
Adjustment
INFOID:0000000009177655
ADJUSTMENT AFTER INSTALLATION
Perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to
.
Bracket
TCM
: N·m (kg-m, in-lb)
JSDIA3618GB
TM-196
< REMOVAL AND INSTALLATION >
[CVT: RE0F10E]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009177656
REMOVAL
1. Remove the front air duct and air cleaner case assembly. Refer to
EM-24, "Removal and Installation"
.
2. Remove air breather hose.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Insert air breather hose (1) to air breather tube (2) all the way
to the curve of the tube.
• Insert air breather hose to air breather tube so that the paint
mark (A) is facing upward.
ALDIA0399ZZ
OIL PAN
TM-197
< REMOVAL AND INSTALLATION >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000009177657
Removal and Installation
INFOID:0000000009177658
REMOVAL
1. Remove drain plug from oil pan and then drain the CVT fluid.
2. Remove drain plug gasket.
CAUTION:
Do not reuse drain plug gasket.
3. Remove the oil pan bolts, and then remove the oil pan and oil pan gasket.
CAUTION:
Do not reuse oil pan gasket.
4. Remove the magnets from the oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse oil pan gasket.
• Do not reuse drain plug gasket.
Transaxle assembly
Oil pan gasket
Oil pan
Drain plug
Drain plug gasket
Magnet
Overflow plug
O-ring
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA4194GB
TM-198
< REMOVAL AND INSTALLATION >
[CVT: RE0F10E]
OIL PAN
• Do not reuse O-ring.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
Install the oil pan to the transaxle case with the following procedure.
1. Install the oil pan gasket to the oil pan.
CAUTION:
Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.
3. Tighten the oil pan bolts in the order shown to the specified
torque.
4.
Tighten the oil pan bolts again clockwise from (1) shown to the
specified torque.
Inspection and Adjustment
INFOID:0000000009177659
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
: Front
JPDIA0664ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст