Nissan X-Trail 32. Manual — part 1570
MA-70
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
DISC BRAKE (RHD) : Rear Disc Brake
INFOID:0000000010953495
Unit: mm (in)
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000010735346
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000010735347
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.070 (0.0028)
JPPIA0013GB
SMA525A
JPPIA0011ZZ
CHASSIS MAINTENANCE
MA-71
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
DRIVE SHAFT : Inspection
INFOID:0000000010735348
• Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SFA108A
MA-72
< PERIODIC MAINTENANCE >
BODY MAINTENANCE
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000010735349
Check the vehicle type to use the service information in DLK section. Refer to
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000010735350
For front seat belt illustration. Refer to
For second seat belt illustration. Refer to
For third seat belt illustration. Refer to
.
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
SB-13, "SEAT BELT RETRACTOR : Inspection"
SB-22, "SEAT BELT RETRACTOR : Inspection"
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
PART
TYPE 1
TYPE 2
Hood
.
Refer to
Hood lock
Refer to
.
Refer to
Front door
Refer to
.
Refer to
Front door lock
Refer to
.
Refer to
Rear door
Refer to
.
Refer to
Rear door lock
Refer to
.
Refer to
Back door
Refer to
.
Refer to
Back door lock
Refer to
.
Refer to
PART
TYPE 3
TYPE 4
Hood
.
Refer to
Hood lock
Refer to
.
Refer to
Front door
Refer to
.
Refer to
Front door lock
Refer to
.
Refer to
Rear door
Refer to
.
Refer to
Rear door lock
Refer to
.
Refer to
Back door
Refer to
.
Refer to
Back door lock
Refer to
.
Refer to
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-73
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELTS (MR20DD)
DRIVE BELTS (MR20DD) : Drive Belt
INFOID:0000000011009240
DRIVE BELT
DRIVE BELTS (QR25DE)
DRIVE BELTS (QR25DE) : Drive belt
INFOID:0000000011009244
DRIVE BELT
DRIVE BELTS (R9M)
DRIVE BELTS (R9M) : Drive Belts
INFOID:0000000010828055
DRIVE BELT
ENGINE COOLANT (MR20DD)
ENGINE COOLANT (MR20DD) : Periodical Maintenance Specification
INFOID:0000000011009255
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(Imp qt)
ENGINE COOLANT (QR25DE)
ENGINE COOLANT (QR25DE) : Periodical Maintenance Specification
INFOID:0000000011009257
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(lmp qt)
ENGINE COOLANT (R9M)
ENGINE COOLANT (R9M) : Periodical Maintenance Specification
INFOID:0000000010828057
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(lmp qt)
ENGINE OIL (MR20DD)
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Tension of drive belt
Belt tensioning is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Engine coolant capacity (With reservoir tank at “MAX” level)
CVT models
7.7 (6-6/8)
M/T models
7.2 (6-3/8)
Reservoir tank engine coolant capacity (At “MAX” level)
0.85 (6/8)
Engine coolant capacity (With reservoir tank at “MAX” level)
8.2 (7-2/8)
Reservoir tank
0.85 (6/8)
Engine coolant capacity (With reservoir tank at “MAX” level)
M/T models
7.9 (7)
CVT models
8.1 (7-1/8)
Reservoir tank
0.57 (4/8)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст