Nissan Juke F15. Manual — part 988
MA-44
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
BRAKE LINES AND CABLES : Inspection
INFOID:0000000012200234
• Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
BRAKE FLUID : Changing
INFOID:0000000012200235
1. Drain brake fluid from each bleed valve.
2. Refill until new brake fluid comes out from each bleed valve.
Use same procedure as in bleeding hydraulic system to refill
brake fluid.
BR-13, "Bleeding Brake System"
• Refill with recommended brake fluid.
Refer to
MA-11, "Fluids and Lubricants"
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted areas.
DISC BRAKE
DISC BRAKE : Inspection
INFOID:0000000012200236
DISC ROTOR
Check condition, wear, and damage.
CALIPER
• Check for leakage.
BRAKE PAD
SBR389C
SBR419C
SMA922A
CHASSIS MAINTENANCE
MA-45
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Check for wear or damage.
DISC BRAKE : Front Disc Brake
INFOID:0000000013001851
EXCEPT NISMO RS
Unit: mm (in)
*To check if rotor imbalance, rotor runout deformation is occured.
NISMO RS
Unit: mm (in)
*To check if rotor imbalance, rotor runout deformation is occured.
DISC BRAKE : Rear Disc Brake
INFOID:0000000013001852
EXCEPT NISMO RS
Unit: mm (in)
*To check if rotor imbalance, rotor runout deformation is occured.
NISMO RS
Unit: mm (in)
*To check if rotor imbalance, rotor runout deformation is occured.
STEERING GEAR AND LINKAGE
BRA0010D
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
24.0 (0.945)
Thickness variation (measured at 8 positions)*
0.008 (0.0003)
Runout (with it attached to the vehicle)
0.035 (0.0014)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
26.0 (1.024)
Thickness variation (measured at 8 positions)*
0.008 (0.0003)
Runout (with it attached to the vehicle)
0.035 (0.0014)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
8.0 (0.315)
Thickness variation (measured at 8 positions)*
0.016 (0.0006)
Runout (with it attached to the vehicle)
0.1 (0.004)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Thickness variation (measured at 8 positions)*
0.016 (0.0006)
Runout (with it attached to the vehicle)
0.1 (0.004)
MA-46
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000012200239
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000012200240
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
DRIVE SHAFT : Inspection
INFOID:0000000012200241
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
JPPIA0013GB
SMA525A
JPPIA0011ZZ
SFA108A
BODY MAINTENANCE
MA-47
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000012200242
For hood and hood lock illustration.
• Hood lock: Refer to
.
For door and door lock illustration.
• Front door: Refer to
• Front door lock: Refer to
• Rear door: Refer to
.
• Rear door lock: Refer to
.
For back door and back door lock illustration.
• Back door: Refer to
• Back door lock: Refer to
.
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000012200243
For front seat belt illustration. Refer to
For rear seat belt illustration. Refer to
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
SB-7, "SEAT BELT RETRACTOR : Inspection"
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст