Nissan Juke F15. Manual — part 987
MA-40
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
TRANSFER OIL : Refilling
INFOID:0000000012200226
1. Remove filler plug (1) and gasket. Then fill oil up to mounting
hole for the filler plug.
CAUTION:
Carefully fill the oil. (Fill up for approximately 3 minutes.)
2. Leave the vehicle for 3 minutes, and check the oil level again.
3. Before installing filler plug, set a new gasket. Install filler plug on transfer and tighten to the specified
CAUTION:
Never reuse gasket.
REAR PROPELLER SHAFT
REAR PROPELLER SHAFT : Inspection
INFOID:0000000012200227
APPEARANCE AND NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, inspect propeller shaft runout first.
1. With a dial indicator, measure propeller shaft runout at runout
measuring points by rotating final drive companion flange with
hands.
• Propeller shaft runout measuring point (Point “ ”)
2. If runout still exceeds specifications, separate propeller shaft at
final drive companion flange or transfer companion flange; then
change the phase between companion flange and propeller
shaft by the one bolt hole at a time and install propeller shaft.
3. Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4. Check the vibration by driving vehicle.
REAR DIFFERENTIAL GEAR OIL
: Vehicle front
Oil and viscosity
: Refer to
.
Oil capacity
: Refer to
.
JSDIA2080ZZ
Propeller shaft runout
: Refer to
.
JPDID0419ZZ
: Front
Dimension
A: 542 mm (21.34 in)
B: 516.5 mm (20.33 in)
JSDIA2286ZZ
CHASSIS MAINTENANCE
MA-41
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
REAR DIFFERENTIAL GEAR OIL : Inspection
INFOID:0000000012200228
OIL LEAKAGE
Check rear final drive surrounding area (oil seal, drain plug, filler plug, and gear carrier, etc.) for oil leakage.
OIL LEVEL
1. Remove filler plug (1) and check oil level from filler plug mount-
ing hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
2. Set a new gasket on filler plug and install it on final drive assem-
bly. Refer to
.
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL : Draining
INFOID:0000000012200229
1. Stop engine.
2. Remove drain plug (1) and drain gear oil.
3. Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL : Refilling
INFOID:0000000012200230
1. Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2. After refilling oil, check oil level. Set a new gasket to filler plug,
then install it to final drive assembly. Refer to
CAUTION:
Never reuse gasket.
WHEELS (BONDING WEIGHT TYPE)
WHEELS (BONDING WEIGHT TYPE) : Wheel Balance Adjustment
INFOID:0000000012200231
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
JSDIA2113ZZ
JSDIA2114ZZ
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
JSDIA2113ZZ
MA-42
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1. Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2. When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Never install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, always to clean the mating surface of the road wheel.
a. Indicated unbalance value
× 5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
× 5/3 = 38.33 g (1.35 oz) ⇒ 40 g (1.41 oz) bal-
ance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒ 35 g (1.23 oz)
37.5
⇒ 40 g (1.41 oz)
b. Installed balance weight in the position.
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Never install three or more sheets of balance weight.
SMA054D
JPEIC0040ZZ
CHASSIS MAINTENANCE
MA-43
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
c. If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Never install one balance weight sheet on top of another.
3. Start the tire balance machine again.
4. Install drive-in balance weight on inner side of road wheel in the
tire balance machine indication position (angle).
CAUTION:
Never install three or more balance weight.
5. Start the tire balance machine. Check that the inner and outer
residual unbalance value is within the allowable unbalance
value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
WHEELS (BONDING WEIGHT TYPE) : Tire Rotation
INFOID:0000000012200232
• Follow the maintenance schedule for tire rotation service intervals.
MA-5, "Explanation of General Maintenance"
.
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Never include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria.
• Use NISSAN genuine wheel nut.
• Perform the ID registration, after tire rotation. Refer to
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Inspection
INFOID:0000000012200233
• If fluid level is extremely low, check brake system for leaks.
BRAKE LINES AND CABLES
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
PEIA0033E
SMA829C
SBR451D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст