Nissan Juke (2016 year). Service Repair Manual — part 380
SILL COVER
EXT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
SILL COVER
Exploded View
INFOID:0000000012199320
Removal and Installation
INFOID:0000000012199321
REMOVAL
1. Remove sill cover front end fixing screw (A).
1.
Screw grommet
2.
Screw grommet
3.
Sill cover
4.
Wind deflector
, , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA5581ZZ
JMKIA5565ZZ
Revision: November 2015
2016 JUKE
EXT-34
< REMOVAL AND INSTALLATION >
SILL COVER
2. Remove sill cover rear end fixing screw (A).
3. Remove sill cover lower side fixing screws.
4. Fully open front door and rear door.
5. Remove fixing clips from sill cover back side with a remover tool
(A).
CAUTION:
Apply protective tape (B) on the body to protect the painted
surface from damage.
6. Remove sill cover form body side.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing sill cover, check that clips are securely fitted in body panel holes, and then press clips
in.
JMKIA5566ZZ
: Clip
JMKIA5567ZZ
Revision: November 2015
2016 JUKE
FLOOR SIDE FAIRING
EXT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FLOOR SIDE FAIRING
Exploded View
INFOID:0000000012199322
Removal and Installation
INFOID:0000000012199323
REMOVAL
FLOOR UNDER COVER
Remove floor under cover mounting nut and push spring nuts, and then remove floor under cover.
INSTALLATION
Install in the reverse order of removal.
1.
Push spring nut
2.
Floor under cover RH
3.
Floor under cover LH
JMKIA5648ZZ
Revision: November 2015
2016 JUKE
EXT-36
< REMOVAL AND INSTALLATION >
FILLET MOLDING
FILLET MOLDING
Exploded View
INFOID:0000000012199324
FRONT FILLET MOLDING
FRONT FILLET MOLDING : Removal and Installation
INFOID:0000000012199325
REMOVAL
1. Remove front fillet molding fixing clips.
2. Remove front fillet molding front side fixing pawls.
CAUTION:
Never pull the front fillet molding strongly.
1.
Grommet
2.
Clip
3.
Clip
4.
Front fillet molding
5.
Rear fillet molding
: Pawl
: Always replace after every disassembly.
, , , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA5582ZZ
: Pawl
JMKIA5583ZZ
Revision: November 2015
2016 JUKE
FILLET MOLDING
EXT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
3. Using remover tool (A), disengage the clips from front fillet mold-
ing by starting from front side.
CAUTION:
• Apply a protective tape (B) on the body to protect the
painted surface from damage.
• Never pull the front fillet molding strongly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always replace fillet molding fixing clips.
• When installing front fillet molding, check that blind clips and pawls are securely fitted in panel holes
on body, and then press them in.
REAR FILLET MOLDING
REAR FILLET MOLDING : Removal and Installation
INFOID:0000000012199326
REMOVAL
1. Remove rear filet molding fixing clip from end of sill cover.
2. Remove rear fillet molding rear side fixing pawls.
CAUTION:
Never pull the rear fillet molding strongly.
3. Using remover tool (A), disengage the clips from rear fillet mold-
ing by starting from rear side.
CAUTION:
• Apply a protective tape (B) on the body to protect the
painted surface from damage.
• Never pull the rear fillet molding strongly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always replace fillet molding fixing clips.
• When installing rear fillet molding, check that blind clips and pawls are securely fitted in panel holes
on body, and then press them in.
: Clip
JMKIA5584ZZ
: Pawl
JMKIA5585ZZ
: Clip
JMKIA5586ZZ
Revision: November 2015
2016 JUKE
EXT-38
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
ROOF SIDE MOLDING
Exploded View
INFOID:0000000012199327
Removal and Installation
INFOID:0000000012199328
REMOVAL
Roof Side Molding
1. Disengage roof side molding rear side fixing clip, using a
remover tool (A).
CAUTION:
Apply protective tape (B) on body to protect the painted
surface from damage.
1.
Roof side molding
2. Roof side molding clip
3.
Double-sided tape
[t: 2.5 mm (0.098 in)]
4.
Body side outer panel
5. Roof panel
: Vehicle front
: Always replace after every disassembly.
JMKIA5649ZZ
: Clip
: Vehicle front
JMKIA5770ZZ
Revision: November 2015
2016 JUKE
ROOF SIDE MOLDING
EXT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2. Pull up roof side molding from rear end to front end.
CAUTION:
Never pull the roof side molding strongly.
3. Disengage windshield molding and clip at the front end of roof
side molding, and then remove while pulling out toward vehicle
rear.
Roof Side Molding Clip
1. Remove roof side molding.
2. Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Never damage the body.
INSTALLATION
Roof Side Molding
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing roof side molding, check that roof side molding are securely in roof side molding
clip, and press them in.
• Replace the double-sided tape on the back surface with new double-sided tape when reusing the
roof side molding.
• Remove double-sided tape remaining on roof panel and back of roof side molding with a double-
sided tape remover, after removing roof side molding.
• When installing, visually check the roof side molding and roof side molding clip, then replace them
with new parts if they are damaged.
Roof Side Molding Clip
1. Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2. Use two-part epoxy adhesive.
3. Apply adhesive evenly to clip tape surface.
4. Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
: Vehicle front
JMKIA3884ZZ
: Clip
JMKIA5650ZZ
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
Revision: November 2015
2016 JUKE
EXT-40
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
5. Tape roof side molding clips after press fit, and temporarily hold it for specified time based on the follow-
ing.
CAUTION:
• Use double-sided tape after hardening for roof side molding clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield glass portion, check that body side molding fas-
tener is securely inserted and then press in.
• Never wash the vehicle within 24 hours so as to keep adhesive.
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст