Nissan Juke (2016 year). Service Repair Manual — part 381
DOOR OUTSIDE MOLDING
EXT-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000012199329
FRONT DOOR OUTSIDE MOLDING
FRONT DOOR OUTSIDE MOLDING : Removal and Installation
INFOID:0000000012199330
REMOVAL
1. Fully open front door glass.
2. Twist door outside molding toward the outside of the vehicle,
and then lift up and remove it while disengaging the pawls.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
1.
Front door panel
2.
Front door outside molding
3.
Rear door panel
4.
Rear door outside molding
5.
Door glass
: Pawl
JMKIA5664GB
: Pawl
JMKIA5801ZZ
Revision: November 2015
2016 JUKE
EXT-42
< REMOVAL AND INSTALLATION >
DOOR OUTSIDE MOLDING
CAUTION:
When installing front door outside molding, check that pawl (1)
is accurately aligned with mounting hole (2), then press in.
REAR DOOR OUTSIDE MOLDING
REAR DOOR OUTSIDE MOLDING : Removal and Installation
INFOID:0000000012199331
REMOVAL
1. Fully open rear door glass.
2. Twist rear door outside molding toward vehicle outside and
remove molding while disengaging it from door panel.
3. Slide rear door outside molding (1) toward vehicle front, and
then pull molding out from rear door handle (2).
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing rear door outside molding, check that pawl (1)
is accurately aligned with mounting hole (2), then press in.
JMKIA5669ZZ
: Pawl
JMKIA5696ZZ
JMKIA5697ZZ
JMKIA5698ZZ
Revision: November 2015
2016 JUKE
DOOR SASH TAPE
EXT-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR SASH TAPE
Exploded View
INFOID:0000000012199332
FRONT DOOR SASH TAPE
FRONT DOOR SASH TAPE : Removal and Installation
INFOID:0000000012199333
REMOVAL
1. Remove front door outside molding. Refer to
EXT-41, "FRONT DOOR OUTSIDE MOLDING : Removal
2. Heat front door sash tape surface using a dryer, and then peel front door sash tape.
CAUTION:
Never damage painted surface of door panel.
INSTALLATION
NOTE:
For installation position of front door sash tape, refer to the position as shown in the figure.
1.
Front door panel
2.
Front door sash tape
3.
Rear door sash tape
4.
Rear door panel
: Always replace after every disassembly.
JMKIA5665ZZ
Revision: November 2015
2016 JUKE
EXT-44
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
CAUTION:
• Degrease front door panel mounting surface for front door sash tape.
• Paint grain or dust on mounting surface of front door sash tape may spoil exterior appearance if it
remains. Clean the mounting surface and check that no paint grain or dust remains, before starting
the operation.
• Never reuse front door sash tape.
1. Affix front door sash tape align front door sash tape upper portion to front door outer upper end.
1.
Front door panel
2.
Front door sash tape
3.
Rear door panel
R. Radius
: Always replace after every disassembly.
D
: 2.0 mm (0.08 in)
E
: 4.0 mm (0.16 in)
JMKIA5666ZZ
Revision: November 2015
2016 JUKE
DOOR SASH TAPE
EXT-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2. Affix front door sash tape (2) to front door panel (3) by applying pressure using a squeegee (A) while peel-
ing off release coated paper (1).
NOTE:
• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affix
front door sash tape.
• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that por-
tion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using
squeegee tilted at 40 – 50
°
angle (pushing direction) (C) 30 – 45
°
angle (pulling direction) (D).
3. For small radius portion of hemming part, gradually apply pres-
sure and affix front door sash tape (1) using squeegee (A) in 1 –
3 steps.
CAUTION:
Never wash the vehicle within 24 hours so as to keep adhe-
sive.
REAR DOOR SASH TAPE
REAR DOOR SASH TAPE : Removal and Installation
INFOID:0000000012199334
REMOVAL
1. Remove rear door outside molding. Refer to
EXT-42, "REAR DOOR OUTSIDE MOLDING : Removal and
.
2. Heat rear door sash tape surface using a dryer, and then peel rear door sash tape.
CAUTION:
Never damage painted surface of door panel.
INSTALLATION
NOTE:
For installation position of rear door sash tape, refer to the position as shown in the figure.
JMKIB1013GB
JMKIB1014ZZ
Revision: November 2015
2016 JUKE
EXT-46
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
CAUTION:
• Degrease rear door panel mounting surface for rear door sash tape.
• Paint grain or dust on mounting surface of rear door sash tape may spoil exterior appearance if it
remains. Clean the mounting surface and check that no paint grain or dust remains, before starting
the operation.
• Never reuse rear door sash tape.
1. Affix rear door sash tape align rear door sash tape upper portion to rear door outer upper end.
1.
Rear door panel
2.
Rear door sash tape
3.
Front door panel
R. Radius
: Always replace after every disassembly.
D
: 2.0 mm (0.08 in)
JMKIA5667ZZ
Revision: November 2015
2016 JUKE
DOOR SASH TAPE
EXT-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2. Affix rear door sash tape (2) to rear door panel (3) by applying pressure using a squeegee (A) while peel-
ing off release coated paper (1).
NOTE:
• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affix
rear door sash tape.
• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that por-
tion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using
squeegee tilted at 40 – 50
°
angle (pushing direction) (C) 30 – 45
°
angle (pulling direction) (D).
3. For small radius portion of hemming part, gradually apply pres-
sure and affix rear door sash tape (1) using squeegee (A) in 1 –
3 steps.
CAUTION:
Never wash the vehicle within 24 hours so as to keep adhe-
sive.
JMKIB1013GB
JMKIB1014ZZ
Revision: November 2015
2016 JUKE
EXT-48
< REMOVAL AND INSTALLATION >
REAR FENDER COVER
REAR FENDER COVER
Exploded View
INFOID:0000000012199335
Removal and Installation
INFOID:0000000012199336
REMOVAL
Disengage rear fender cover fixing clips using a remover tool (A),
and then remove rear fender cover.
CAUTION:
Apply protective tape (B) to the body side to protect from dam-
age.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing rear fender cover, check that clips are securely fitted in body panel holes, and then
press them it.
JMKIB4682ZZ
1.
Rear fender cover
2.
Clip
3.
Seal packing
4.
Rear fender
: Always replace after every disassembly.
: Clip
JMKIA5668ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст