Nissan Juke (2016 year). Service Repair Manual — part 382
REAR SPOILER
EXT-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REAR SPOILER
Exploded View
INFOID:0000000012199337
Removal and Installation
INFOID:0000000012199338
REMOVAL
1. Fully open back door.
2. Remove grommet of back door inside, and then remove rear spoiler mounting nuts.
1.
Rear spoiler
2.
High-mounted stop lamp
3.
High-mounted stop lamp cover
4.
Double-sided tape
[t: 2.0 mm (0.079 in)]
5.
Double-sided tape
[t: 1.2 mm (0.047 in)]
: Clip
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual vehicle.
JSKIA3180GB
Revision: November 2015
2016 JUKE
EXT-50
< REMOVAL AND INSTALLATION >
REAR SPOILER
3. Apply protective tape (A) on body to protect the painted surface
from damage.
4. Insert a remover tool (A) between rear spoiler and back door
panel, cut double-sided tape using a cutter (B) while lifting rear
spoiler.
CAUTION:
Never damage the back door and rear spoiler.
5. Remove rear spoiler fixing clips using a remover tool (A).
6. Disconnect high-mounted stop lamp harness connector, and then remove rear spoiler.
7. Remove high-mounted stop lamp after removing rear spoiler: Refer to
EXL-111, "Removal and Installa-
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace the double-sided tape on the back surface with new double-sided tape when reusing the
rear spoiler.
• Remove double-sided tape remaining on back door assembly and back of rear spoiler with a double-
sided tape remover, after removing rear spoiler.
• When installing, visually check the rear spoiler and clips, then replace them with new parts if they
are damaged.
• When installing rear spoiler, check clips and bolts are securely in back door assembly holes, and
press them in.
• Never wash the vehicle within 24 hours after installing so as to keep adhesive.
JMKIB1769ZZ
JMKIB1770ZZ
: Clip
JMKIB1771ZZ
Revision: November 2015
2016 JUKE
BACK DOOR FINISHER
EXT-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
BACK DOOR FINISHER
Exploded View
INFOID:0000000012199339
Removal and Installation
INFOID:0000000012199340
REMOVAL
1. Remove back door lower finisher. Refer to
INT-39, "BACK DOOR LOWER FINISHER : Removal and
.
2. Remove back door finisher mounting nuts.
3. Disconnect license lamp, back door opener request switch and rear view camera harness connectors.
4. Remove harness grommet.
5. Disengage back door finisher fixing clips using a remover tool
(A).
6. Disengage back door finisher fixing clips at both ends of back
door finisher from inside of back door.
CAUTION:
• Apply protect tape (B) on back door panel to protect the
painted surface from damage.
• Never pull back door finisher strongly.
1.
Rear view camera
2.
Back door opener request switch
3.
Emblem
4.
Back door finisher
: Clip
: Pawl
: Always replace after every disassembly.
JMKIA5733ZZ
: Clip
JMKIA6179ZZ
Revision: November 2015
2016 JUKE
EXT-52
< REMOVAL AND INSTALLATION >
BACK DOOR FINISHER
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing back door finisher, check that clip are securely in body panel holes, and press them in.
Revision: November 2015
2016 JUKE
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
TYPE 1
HOW TO USE THIS MANUAL . . . . . ..
HOW TO USE THIS SECTION . . . . . . .
Information . . . . . . . . . . . . . . . ....
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT WHEEL HUB AND KNUCKLE . . . ..
Inspection . . . . . . . . . . . . . . . . ..
FRONT DRIVE SHAFT . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
FRONT WHEEL HUB AND KNUCKLE . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT DRIVE SHAFT BOOT . . . . . . ..
2WD . . . . . . . . . . . . . . . . . . .
2WD : Exploded View . . . . . . . . . . . ..
2WD : Removal and Installation . . . . . . . ..
2WD : Inspection . . . . . . . . . . . . . .
AWD . . . . . . . . . . . . . . . . . . ...
AWD : Exploded View . . . . . . . . . . . .
AWD : Removal and Installation . . . . . . . ..
AWD : Inspection . . . . . . . . . . . . . .
FRONT DRIVE SHAFT . . . . . . . . . .
2WD . . . . . . . . . . . . . . . . . . .
2WD : Exploded View . . . . . . . . . . . ..
2WD : Removal and Installation . . . . . . . ..
2WD : Disassembly and Assembly . . . . . . ..
2WD : Inspection . . . . . . . . . . . . . .
AWD . . . . . . . . . . . . . . . . . . ...
AWD : Exploded View . . . . . . . . . . . .
AWD : Removal and Installation . . . . . . . ..
AWD : Disassembly and Assembly . . . . . . .
AWD : Inspection . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
TYPE 2
HOW TO USE THIS MANUAL . . . . .
HOW TO USE THIS SECTION . . . . . . .
Information . . . . . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Revision: November 2015
2016 JUKE
FAX-2
Precautions for Drive Shaft . . . . . . . . . .
Precautions for Removing Battery Terminal . . ...
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tool . . . . . . . . . . . ...
Commercial Service Tools . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . ...
PERIODIC MAINTENANCE . . . . . .
FRONT WHEEL HUB AND KNUCKLE . . . .
Inspection . . . . . . . . . . . . . . . ...
FRONT DRIVE SHAFT . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
FRONT WHEEL HUB AND KNUCKLE . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
FRONT DRIVE SHAFT BOOT . . . . . . ..
2WD . . . . . . . . . . . . . . . . . . ...
2WD : Exploded View . . . . . . . . . . . .
2WD : Removal and Installation . . . . . . . ..
2WD : Inspection . . . . . . . . . . . . . .
AWD . . . . . . . . . . . . . . . . . . ..
AWD : Exploded View . . . . . . . . . . . .
AWD : Removal and Installation . . . . . . . .
AWD : Inspection . . . . . . . . . . . . .
FRONT DRIVE SHAFT . . . . . . . . . ..
2WD . . . . . . . . . . . . . . . . . . ...
2WD : Exploded View . . . . . . . . . . . .
2WD : Removal and Installation . . . . . . . ..
2WD : Disassembly and Assembly . . . . . . .
2WD : Inspection . . . . . . . . . . . . . .
AWD . . . . . . . . . . . . . . . . . . ..
AWD : Exploded View . . . . . . . . . . . .
AWD : Removal and Installation . . . . . . . .
AWD : Disassembly and Assembly . . . . . ...
AWD : Inspection . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . ..
Drive Shaft . . . . . . . . . . . . . . .
Revision: November 2015
2016 JUKE
HOW TO USE THIS SECTION
FAX-3
< HOW TO USE THIS MANUAL >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
HOW TO USE THIS MANUAL
HOW TO USE THIS SECTION
Information
INFOID:0000000012990041
Service information
Model information
TYPE 1
For NISMO models
TYPE 2
Except for NISMO models
Revision: November 2015
2016 JUKE
FAX-4
< PRECAUTION >
[TYPE 1]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012201543
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, it is recommended that all maintenance
and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery or batteries, and wait at least 3 minutes before performing any service.
Precautions for Drive Shaft
INFOID:0000000012201544
• Observe the following precautions when disassembling and assembling drive shaft.
- Never disassemble joint sub-assembly because it is non-overhaul parts.
- Perform work in a location which is as dust-free as possible.
- Clean the parts, before disassembling and assembling.
- Prevent the entry of foreign objects during disassembly of the service location.
- Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
- Use paper waste. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
- Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Precautions for Removing Battery Terminal
INFOID:0000000012833641
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст