Nissan Murano Z51 (2008 year). Manual — part 268
MWI
METER SYSTEM
MWI-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FUEL GAUGE : Component Parts Location
INFOID:0000000003469960
JPNIA0813ZZ
1.
Fuel level sensor unit (sub)
2.
ABS actuator and electric unit (con-
trol unit)
3.
Oil pressure switch
4.
TCM
5.
Ambient sensor
6.
ECM
7.
IPDM E/R
8.
BCM
9.
Combination meter
10.
Fuel level sensor unit and fuel pump
(main)
Revision: 2008 October
2009 Murano
MWI-18
< FUNCTION DIAGNOSIS >
METER SYSTEM
FUEL GAUGE : Component Description
INFOID:0000000003415772
ODO/TRIP METER
ODO/TRIP METER : System Diagram
INFOID:0000000003415773
ODO/TRIP METER : System Description
INFOID:0000000003415774
• The ABS actuator and electric unit (control unit) reads the rectangular wave signal provided by the wheel
sensor and transmits the vehicle speed signal to the combination meter via CAN communication.
• The combination meter converts the vehicle speed signal received via CAN communication to mileage, and
it displays the accumulated mileage to the odo/trip meter.
A.
Lower right side of rear seat
B.
Engine room (RH)
C.
Engine front side
D.
Engine room (LH)
E.
Front bumper (left back)
F.
Engine room (LH)
G.
Engine room (LH)
H.
Behind the combination meter
I.
Lower left side of rear seat
Unit
Description
Combination meter
Indicates the fuel gauge according to the fuel level sensor signal received from the fuel level sensor
unit.
Fuel level sensor unit
Refer to
.
JSNIA0293GB
Revision: 2008 October
2009 Murano
MWI
METER SYSTEM
MWI-19
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ODO/TRIP METER : Component Parts Location
INFOID:0000000003469961
JPNIA0813ZZ
1.
Fuel level sensor unit (sub)
2.
ABS actuator and electric unit (con-
trol unit)
3.
Oil pressure switch
4.
TCM
5.
Ambient sensor
6.
ECM
7.
IPDM E/R
8.
BCM
9.
Combination meter
10.
Fuel level sensor unit and fuel pump
(main)
Revision: 2008 October
2009 Murano
MWI-20
< FUNCTION DIAGNOSIS >
METER SYSTEM
ODO/TRIP METER : Component Description
INFOID:0000000003415776
SHIFT POSITION INDICATOR
SHIFT POSITION INDICATOR : System Diagram
INFOID:0000000003415486
SHIFT POSITION INDICATOR : System Description
INFOID:0000000003415487
• Shift position is displayed in the shift position indicator in the combination meter.
• TCM transmits the shift position signal to the combination meter via CAN communication.
• The combination meter indicates shift position according to the shift position signal received via CAN com-
munication.
A.
Lower right side of rear seat
B.
Engine room (RH)
C.
Engine front side
D.
Engine room (LH)
E.
Front bumper (left back)
F.
Engine room (LH)
G.
Engine room (LH)
H.
Behind the combination meter
I.
Lower left side of rear seat
Unit
Description
Combination meter
Converts the vehicle speed signal received from the ABS actuator and electric unit (control unit) via
CAN communication to mileage, and it displays the accumulated mileage to the odo/trip meter.
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter via CAN communication.
JPNIA0745GB
Revision: 2008 October
2009 Murano
MWI
METER SYSTEM
MWI-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SHIFT POSITION INDICATOR : Component Parts Location
INFOID:0000000003469967
JPNIA0813ZZ
1.
Fuel level sensor unit (sub)
2.
ABS actuator and electric unit (con-
trol unit)
3.
Oil pressure switch
4.
TCM
5.
Ambient sensor
6.
ECM
7.
IPDM E/R
8.
BCM
9.
Combination meter
10.
Fuel level sensor unit and fuel pump
(main)
Revision: 2008 October
2009 Murano
MWI-22
< FUNCTION DIAGNOSIS >
METER SYSTEM
SHIFT POSITION INDICATOR : Component Description
INFOID:0000000003415489
WARNING LAMPS/INDICATOR LAMPS
WARNING LAMPS/INDICATOR LAMPS : System Diagram
INFOID:0000000003415777
WARNING LAMPS/INDICATOR LAMPS : System Description
INFOID:0000000003415778
OIL PRESSURE WARNING LAMP
• IPDM E/R reads the ON/OFF signals from the oil pressure switch and transmits the oil pressure switch sig-
nal to the combination meter via BCM with the CAN communication line.
• The combination meter turns the oil pressure warning lamp ON/OFF according to the oil pressure switch sig-
nal received via CAN communication.
A.
Lower right side of rear seat
B.
Engine room (RH)
C.
Engine front side
D.
Engine room (LH)
E.
Front bumper (left back)
F.
Engine room (LH)
G.
Engine room (LH)
H.
Behind the combination meter
I.
Lower left side of rear seat
Unit
Description
Combination meter
Displays the shift position on the shift position indicator with shift position signal received from TCM
via CAN communication.
TCM
Transmits shift position signal to the combination meter with CAN communication.
JSNIA0449GB
Revision: 2008 October
2009 Murano
MWI
METER SYSTEM
MWI-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
WARNING LAMPS/INDICATOR LAMPS : Component Parts Location
INFOID:0000000003469968
JPNIA0813ZZ
1.
Fuel level sensor unit (sub)
2.
ABS actuator and electric unit (con-
trol unit)
3.
Oil pressure switch
4.
TCM
5.
Ambient sensor
6.
ECM
7.
IPDM E/R
8.
BCM
9.
Combination meter
10.
Fuel level sensor unit and fuel pump
(main)
Revision: 2008 October
2009 Murano
MWI-24
< FUNCTION DIAGNOSIS >
METER SYSTEM
WARNING LAMPS/INDICATOR LAMPS : Component Description
INFOID:0000000003415780
METER ILLUMINATION CONTROL
METER ILLUMINATION CONTROL : System Diagram
INFOID:0000000003415494
METER ILLUMINATION CONTROL : System Description
INFOID:0000000003415495
SYSTEM DESCRIPTION
The combination meter controls the meter illumination by the illumination control switch signal from the meter
control switch and the position light request signal transmitted by the BCM via CAN communication.
Daytime Mode
Meter illumination level can be adjusted in 22 steps using the illumi-
nation control switch (1) in daytime mode.
Nighttime Mode
• Combination meter changes the meter illumination to the nighttime mode by the position light request signal
from BCM via CAN communication.
• Meter illumination can be adjusted in 22 steps using the illumination control switch in nighttime mode.
Driver Welcome Function
Ring illumination gradually turns ON when a driver gets in the vehicle with intelligent key and closes the driver
side door.
NOTE:
Ring illumination gradually turns OFF when not turning the ignition switch ON at a certain period of time.
A.
Lower right side of rear seat
B.
Engine room (RH)
C.
Engine front side
D.
Engine room (LH)
E.
Front bumper (left back)
F.
Engine room (LH)
G.
Engine room (LH)
H.
Behind the combination meter
I.
Lower left side of rear seat
Unit
Description
Combination meter
Turns the oil pressure warning lamp ON/OFF according to the oil pressure switch signal received
from BCM via CAN communication.
IPDM E/R
Reads the ON/OFF signals from the oil pressure switch and transmits the oil pressure switch signal
to the combination meter via BCM and CAN communication.
Oil pressure switch
Refer to
BCM
Transmits the oil pressure switch signal received from IPDM E/R via CAN communication to the
combination meter via CAN communication.
JPNIA0746GB
JPNIA0742ZZ
Revision: 2008 October
2009 Murano
MWI
METER SYSTEM
MWI-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Dial Effects Function
Combination meter detects the engine start when input engine speed signal at first. Pointers of speed meter
and tachometer sweep and ring illumination gradually turns ON when combination meter detects the engine
start. Then, combination meter starts the normal control.
NOTE:
• Engine coolant temperature gauge and fuel gauge do not function.
• Dial Effects Function can be turned ON/OFF from “SETTING” on the information display.
METER ILLUMINATION CONTROL : Component Parts Location
INFOID:0000000003469985
JPNIA0813ZZ
Revision: 2008 October
2009 Murano
MWI-26
< FUNCTION DIAGNOSIS >
METER SYSTEM
METER ILLUMINATION CONTROL : Component Description
INFOID:0000000003415497
INFORMATION DISPLAY
INFORMATION DISPLAY : System Diagram
INFOID:0000000003415498
INFORMATION DISPLAY : System Description
INFOID:0000000003415499
DESCRIPTION
1.
Fuel level sensor unit (sub)
2.
ABS actuator and electric unit (con-
trol unit)
3.
Oil pressure switch
4.
TCM
5.
Ambient sensor
6.
ECM
7.
IPDM E/R
8.
BCM
9.
Combination meter
10.
Fuel level sensor unit and fuel pump
(main)
A.
Lower right side of rear seat
B.
Engine room (RH)
C.
Engine front side
D.
Engine room (LH)
E.
Front bumper (left back)
F.
Engine room (LH)
G.
Engine room (LH)
H.
Behind the combination meter
I.
Lower left side of rear seat
Unit
Description
Combination meter
Controls the meter illumination with the illumination control switch signal from the meter control
switch and the position light request signal from BCM via CAN communication.
BCM
Transmits the position light request signal to the combination meter via CAN communication.
Meter control switch
Transmits the following signals to the combination meter.
• Illumination control switch signal (+)
• Illumination control switch signal (–)
JPNIA0747GB
Revision: 2008 October
2009 Murano
MWI
METER SYSTEM
MWI-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• The combination meter receives the information required for controlling the operations of the information dis-
play from the BCM via CAN communication.
• The combination meter incorporates a trip computer that displays the warning / information according to the
information received from various units.
PARKING BRAKE RELEASE WARNING
The combination meter indicates the parking brake release warning judged by the vehicle speed signal
received from the ABS actuator and electric unit (control unit) via CAN communication and the parking brake
switch signal from the parking brake switch.
Warning Operation Condition
Parking brake release warning is judged if all of the following conditions are fulfilled.
• Vehicle speed is 7 km/h (4.3 MPH) or higher
• Parking brake switch ON
LOW FUEL WARNING
The combination meter indicates the low fuel warning judged by the fuel level sensor signal received from the
fuel level sensor unit.
Warning Operation Condition
• Fuel level: Approx. 11 (2-7/8 US gal, 2-3/8 Imp gal) or less
LOW WASHER FLUID WARNING
The combination meter indicates the low washer fluid warning judged by the signal from the washer level
switch.
Warning Operation Condition
• Indicates the warning when the washer level switch is ON for 180 seconds or more. Stops indicating the
warning when the washer level switch is OFF for 30 seconds or more.
DOOR OPEN WARNING
• The combination meter indicates the door open warning judged by each door switch signal received from the
BCM via CAN communication line.
INSTANTANEOUS FUEL CONSUMPTION
• The combination meter receives the fuel consumption monitor signal from the ECM and the vehicle speed
signal from the ABS actuator and electric unit (control unit) via CAN communication.
• The combination meter calculates instantaneous fuel consumption according to the fuel consumption moni-
tor signal and the vehicle speed signal received via CAN communication.
AVERAGE FUEL CONSUMPTION
• The combination meter receives the fuel consumption monitor signal from the ECM and the vehicle speed
signal from the ABS actuator and electric unit (control unit) via CAN communication.
• The combination meter calculates the average fuel consumption according to the fuel consumption monitor
signal and the vehicle speed signal received via CAN communication.
• The average fuel consumption displayed on the information display is uploaded in approximately 30-second
intervals.
NOTE:
When turning ON the ignition switch after triggering a reset or removing/installing the battery, “
−−−−
” is indi-
cated until 30-seconds/500 m (0.31 miles) of driving.
AVERAGE VEHICLE SPEED
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication.
JSNIA0033GB
Revision: 2008 October
2009 Murano
MWI-28
< FUNCTION DIAGNOSIS >
METER SYSTEM
• Measures the time while the ignition switch is ON through the combination meter.
• The combination meter the average vehicle speed according to the above signals.
• The average vehicle speed displayed on the information display is uploaded in approximately 30-second
intervals.
NOTE:
When turning ON the ignition switch after triggering a reset or removing/installing the battery, “
−−−−
” is indi-
cated until 30 seconds.
TRAVEL TIME
Measures the time while the ignition switch is ON through the combination meter.
TRAVEL DISTANCE
• The combination meter receives the vehicle speed signal from the ABS actuator and electric unit (control
unit) via CAN communication.
• The combination meter calculates the vehicle distance according to the vehicle speed signal. The vehicle
distance is displayed.
POSSIBLE DRIVING DISTANCE
The combination meter calculates possible driving distance according to the vehicle speed signal and fuel
consumption monitor signal transmitted via CAN communication and the fuel level sensor signal transmitted
from the fuel level sensor.
NOTE:
• When turning ON the ignition switch after removing/installing the battery, “
−−−−
” is indicated until 30 sec-
onds.
• The indicated values may not match each other when refueling with the ignition switch ON. Refer to
143, "INFORMATION DISPLAY : Description"
AMBIENT AIR TEMPERATURE
• The combination meter receives the ambient sensor signal from the ambient sensor.
• The combination meter calculates the ambient temperature according to the ambient sensor signal.
• The indicated temperature does not increase if the vehicle speed is less than 20 km/h (12 MPH).
NOTE:
• The ambient sensor input value that is displayed on “Data Monitor” of CONSULT-III is the value before the
correction. It may not match the indicated temperature on the information display.
• The ambient temperature may be indicated higher than the actual temperature, depending on heat in the
engine, the road surface temperature, and so on.
SETTING
Setting item list
Items
Setting range
Setting unit
Description
ALERT
TIME TO REST
No setting - 6 hours
30 minutes,
[60 minutes]*
Time to rest is displayed on the informa-
tion display if the vehicle reached the set
travel distance.
ICY
ON/OFF
—
Low outside temp is displayed on the in-
formation display if the ambient tempera-
ture is 3
°
C (37
°
F) or less.
MAINTENANCE
ENGINE OIL
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The engine oil replacement interval is dis-
played on the information display if the ve-
hicle reached the set distance.
OIL FILTER
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The oil filter replacement interval is dis-
played on the information display if the ve-
hicle reached the set distance.
TIRE
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The tire replacement interval is displayed
on the information display if the vehicle
reached the set distance.
OTHER
No setting - 18,500 miles,
(No setting - 30,000 km)
250 miles (500 km),
[500 miles (1,000 km)]*
The other replacement interval is dis-
played on the information display if the ve-
hicle reached the set distance.
Revision: 2008 October
2009 Murano
MWI
METER SYSTEM
MWI-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
* : Press and hold the switch (1 second or more).
INFORMATION DISPLAY : Component Parts Location
INFOID:0000000003469986
DISPLAY
LANGUAGE
ENGLISH/FRANCAIS
—
The language setting can be changed.
UNIT
US/METRIC
—
The unit setting can be changed.
DIAL EFFECTS
ON/OFF
—
The dial effects setting can be changed.
Items
Setting range
Setting unit
Description
JPNIA0813ZZ
Revision: 2008 October
2009 Murano
MWI-30
< FUNCTION DIAGNOSIS >
METER SYSTEM
INFORMATION DISPLAY : Component Description
INFOID:0000000003415501
1.
Fuel level sensor unit (sub)
2.
ABS actuator and electric unit (con-
trol unit)
3.
Oil pressure switch
4.
TCM
5.
Ambient sensor
6.
ECM
7.
IPDM E/R
8.
BCM
9.
Combination meter
10.
Fuel level sensor unit and fuel pump
(main)
A.
Lower right side of rear seat
B.
Engine room (RH)
C.
Engine front side
D.
Engine room (LH)
E.
Front bumper (left back)
F.
Engine room (LH)
G.
Engine room (LH)
H.
Behind the combination meter
I.
Lower left side of rear seat
Unit
Description
Combination meter
Controls the information display according to the signal received from each unit.
Fuel level sensor unit
Refer to
ECM
Transmits the following signals to the combination meter via CAN communication.
• Engine speed signal
• Fuel consumption monitor signal
ABS actuator and electric unit
(control unit)
Transmits the vehicle speed signal to the combination meter via CAN communication.
BCM
Transmits signals provided by various units to the combination meter via CAN communication.
Meter control switch
Transmits the following signals to the combination meter.
• Enter switch signal
• Select switch signal
Washer level switch
Transmits the washer level signal to the combination meter.
Parking brake switch
Refer to
Door switch
Transmits the door switch signals to BCM.
IPDM E/R
Transmits the ambient sensor signal to the combination meter.
Ambient sensor
Detects the ambient air temperature and transmits the ambient sensor signal to the IPDM E/R.
Revision: 2008 October
2009 Murano
MWI
COMPASS
MWI-31
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
COMPASS
Description
INFOID:0000000003415502
DESCRIPTION
• This electronic compass is able to display 8 primary directions: N, NE, E, SE, S, SW, W, NW.
• The compass switch (1) is used to operate the compass.
Switch Operation
• All standard compasses determine direction relative to magnetic north, however, this electronic compass is
designed to display direction relative to true north.
• The difference between magnetic north and true north varies from place to place across the surface of the
earth.
• This electronic compass must be “told” approximately where it is on the earth’s surface so that the magnetic
north reading can be properly converted into a true north display.
• To tell the electronic compass where it’s at, the earth is separated into numbered “Zone Variances”. The
zone variance number in which the compass is to function must be entered into this electronic compass.
• Each zone is magnetically about 4.2
°
wide. Typically, anything under a 22.5
°
total zone change is not noticed
on the electronic compass display. However, if a change over 22.5
°
occurs, a reading may be off by one or
more primary directions.
• On long trips, the vehicle may leave its original zone and enter one or more new zones. Generally, you do
not need to reset the compass zone if you travel between 3 or 4 zones, such as business travel or vacation.
The typical driver will not notice any difference on the display within 3 or 4 zones. However, if the vehicle is
“permanently” moved to a new location, it is recommended that the compass zone be reset.
ZONE VARIATION SETTING PROCEDURE
1.
Press and hold the compass switch for 3 – 9 seconds.
2.
The current zone setting appears on the compass display.
3.
Find the current geographical location number in the zone varia-
tion chart.
4.
Select the new zone number. (Press the compass switch until
the new zone number appears on the compass display.)
5.
After select the new zone number, the compass display will
automatically shows a direction within a few seconds.
6.
Perform the following calibration procedure for more accurate
indications.
Press
Compass is turned ON/OFF
Press and hold
(for 3- 9 sec.)
Compass display (2) turns to zone variation change
mode
Press and hold (for more
than 9 sec.)
Compass display turns to calibration mode
SKIB8868E
SEL168Y
Revision: 2008 October
2009 Murano
MWI-32
< FUNCTION DIAGNOSIS >
COMPASS
CALIBRATION PROCEDURE
NOTE:
The compass calibrates itself under normal driving conditions. However, occasional circumstances may cause
the compass to operate inaccurately. Example: Driving from rural (wide open) areas to crowded city areas, or
if an aftermarket (i.e., non original equipment) antenna with a magnetic base is attached to the vehicle. Cali-
brate the mirror compass if the display shows only one direction or a limited number of directions.
NOTE:
• If “magnetic hats” are used in the dealership for vehicle identification, remove the hat from the vehicle before
performing the following steps. Do not put the hat back on the vehicle after the procedure is completed.
• Drive the vehicle to an open level area; away from large metallic objects, structures, and overhead power
lines.
• Turn off “non-essential” electrical accessories (rear window defrost, heater/air conditioning, wipers) and
close the doors.
1.
Verify the correct compass zone setting for the geographical location.
2.
Press and hold the compass switch for more than 9 seconds.
3.
“C” is displayed on the compass display when calibration starts.
4.
Drive slowly [less than 8 km/h (5 MPH)] in a circle until the “C / CAL” is replaced with primary headings (N,
NE, E, SE, S, SW, W, or NW).
NOTE:
This will require driving at least 2 complete 360 degree circles, 3 complete circles may be required.
5.
The compass calibration procedure is now complete. The compass should operate normally.
NOTE:
If at any time the compass continually displays the incorrect direction or the reading is erratic or locked,
repeat the calibration procedure.
Component Parts Location
INFOID:0000000003415503
Special Repair Requirement
INFOID:0000000003415504
1.
PERFORM ZONE VARIATION SETTING
Perform the zone variation setting. Refer to
.
>> GO TO 2.
2.
PERFORM CALIBRATION
Perform the calibration. Refer to
.
>> Setting completion
1
: Compass switch
2
: Compass display
SKIB8868E
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст