Nissan Murano Z51 (2008 year). Manual — part 334
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
SEC-247
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ENGINE START FUNCTION : Component Description
INFOID:0000000003465854
10. Horn (low) E342, E343
11.
Control device (detection switch) M57
12. Stop lamp switch
TYPE A: E115
TYPE B: E116
13. Remote keyless entry receiver
A.
Behind the combination meter
B.
Engine room (LH)
C.
View with the center console as-
sembly removed
D.
Behind the instrument lower panel LH
E.
Behind the instrument lower panel RH
1.
Back door lock assembly (back door
switch) D180
2.
Front door switch (driver side) B34
3.
Power window main switch (door
lock and unlock switch) D5, D6
4.
Front power window switch (passen-
ger side) D45
JMKIA1913ZZ
Component Reference
BCM
Steering lock unit
Push-button ignition switch
Door switch
key slot
Control device (detention switch)
Stop lamp switch
Park/neutral position switch
Steering lock relay
Starter relay
Starter control relay
Revision: 2008 October
2009 Murano
SEC-248
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
WARNING FUNCTION
WARNING FUNCTION : System Description
INFOID:0000000003510971
OPERATION DESCRIPTION
The warning function are as follows and are given to the user as warning information and warnings using com-
binations of outside warning buzzer, KEY warning lamp, key slot illumination and combination meter display in
combination meter.
• Engine start function malfunction
• OFF position warning
• P position warning
• ACC warning
• Key warning
• Keyfob insert information
• Engine start information
• Steering lock information
• Key ID warning
OPERATION CONDITION
Once the following condition from below is established, alert or warning will be executed.
Security indicator
Key warning lamp
Component Reference
Warning/Information functions
Operation procedure
Engine start function malfunction
When a malfunction is detected on BCM, “KEY” warning lamp will illuminate.
OFF position warning
For internal
• Ignition switch: ACC position.
• Door switch (driver side): ON (Door is open).
• Keyfob is removed from key slot.
For external
• OFF position warning (For internal) is in active mode, each door has been
closed.
• Keyfob is removed from key slot.
NOTE:
OFF position (For external) active only when each of the sequence has oc-
curred as below: P position warning
→
ACC warning
→
OFF position warning
(For internal)
→
OFF position warning (For internal)
ACC warning
• During P position warning is in active mode, shift position has changed P po-
sition.
• Ignition switch: ACC position.
• Shift position: Except P position
• Ignition switch: Except ON position.
P position warning
Door is open
• Door switch: ON (Door is open)
Keyfob is removed from
key slot
• Keyfob is removed from key slot.
• Door switch: ON to OFF (door is open to close).
Key warning
• Ignition switch is OFF position.
• Driver side door switch: ON (Driver side door is open).
• Keyfob is inserted in key slot.
Keyfob insert information
• Ignition switch: Except OFF position.
• Keyfob is removed from key slot.
Engine start information
Ignition switch is ON posi-
tion
• Ignition switch: ON position.
• Shift position: P position
• Engine is stopped
Ignition switch is except
ON position
• Ignition switch: Except ON position.
• Shift position: P position
• Keyfob is inserted in key slot.
Revision: 2008 October
2009 Murano
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
SEC-249
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
WARNING METHOD
The following table shows the alarm or warning methods with chime.
Meter display, “KEY” indicator or key slot illumination when the warning conditions are met.
Steering lock information
When steering lock can not be released after ignition switch is turned ON.
Key ID warning
• Ignition switch: Except OFF position.
• Keyfob is remove from key slot.
Warning/Information functions
Operation procedure
Warning/Information functions
“KEY” warn-
ing lamp
Combination meter display
Key slot il-
lumination
Warning chime
Combination
meter buzzer
Outside
warning
buzzer
Engine start function malfunction
Illuminate
—
—
—
—
OFF position warn-
ing
For internal
—
—
Activate
—
For external
—
—
—
—
Activate
ACC warning
—
—
—
—
P position warning
—
—
Activate
—
Door is open
—
—
Activate
—
Keyfob is re-
moved from key
slot
—
—
Activate
Activate
Key ID warning
—
Flash
—
—
Key warning
—
Flash
Activate
—
JMKIA0036GB
JMKIA0047GB
JMKIA0037GB
JMKIA0036GB
JMKIA0035GB
Revision: 2008 October
2009 Murano
SEC-250
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
Keyfob insert information
—
Flash
—
—
Engine start information
—
—
—
—
Steering lock information
—
—
—
—
Keyfob low battery warning
—
—
—
—
Warning/Information functions
“KEY” warn-
ing lamp
Combination meter display
Key slot il-
lumination
Warning chime
Combination
meter buzzer
Outside
warning
buzzer
JMKIA0034GB
JMKIA0032GB
JMKIA0033GB
JMKIA0048GB
Revision: 2008 October
2009 Murano
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
SEC-251
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
WARNING FUNCTION : Component Parts Location
INFOID:0000000003511005
1.
BCM M118, M119, M121, M122, M123
2.
TCM F23
3.
IPDM E/R E10, E11, F12
4.
ECM E16
5.
Push-button ignition switch M101
6.
Key slot M99
7.
Combination meter (key warning lamp)
M34
8.
Security indicator lamp M100
9.
Horn (high) E340, E341
10. Horn (low) E342, E343
11.
Control device (detection switch) M57
12. Stop lamp switch
TYPE A: E115
TYPE B: E116
13. Remote keyless entry receiver
A.
Behind the combination meter
B.
Engine room (LH)
C.
View with the center console as-
sembly removed
D.
Behind the instrument lower panel LH
E.
Behind the instrument lower panel RH
JMKIA1825ZZ
Revision: 2008 October
2009 Murano
SEC-252
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
1.
Back door lock assembly (back door
switch) D180
2.
Front door switch (driver side) B34
3.
Power window main switch (door
lock and unlock switch) D5, D6
4.
Front power window switch (passen-
ger side) D45
JMKIA1913ZZ
Revision: 2008 October
2009 Murano
VEHICLE SECURITY SYSTEM
SEC-253
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
VEHICLE SECURITY SYSTEM
System Diagram
INFOID:0000000003465855
System Description
INFOID:0000000003465856
OPERATION FLOW
SETTING THE VEHICLE SECURITY SYSTEM
Initial Condition
• Ignition switch is in OFF position.
Disarmed Phase
• When any door or back door is open, the vehicle security system is set in the disarmed phase on the
assumption that the owner is inside or near the vehicle.
JMKIA3709GB
PIIA1367E
Revision: 2008 October
2009 Murano
SEC-254
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM
• When the vehicle security system is in the disarmed phase, the security indicator lamp blinks every 2.4 sec-
onds.
Pre-armed Phase and Armed Phase
When the following operation is performed, the vehicle security system turns into the “pre-armed” phase. (The
security indicator lamp illuminates.)
1.
BCM receives LOCK signal from keyfob or door key cylinder, after back door and all doors are closed.
2.
Security indicator lamp illuminates for 30 seconds. Then, the system automatically shifts into the “armed”
phase.
CANCELING THE SET VEHICLE SECURITY SYSTEM
When one of the following operations is performed, the armed phase is canceled.
1.
Unlock the all doors with keyfob or door key cylinder.
2.
Turn ignition switch “ON” or “ACC” position.
CANCELING THE ALARM OPERATION OF THE VEHICLE SECURITY SYSTEM
When unlocking the all doors with keyfob or door key cylinder the alarm operation is canceled.
ACTIVATING THE ALARM OPERATION OF THE VEHICLE SECURITY SYSTEM
Check that the system is in the armed phase. (The security indicator lamp blinks every 2.4 seconds.)
When the following operation 1 or 2 is performed, the system sounds the horns and flashes the headlamps for
about 50 seconds.
1.
Back door or any door is opened during armed phase.
2.
Disconnecting and connecting the battery connector before canceling armed phase.
Revision: 2008 October
2009 Murano
VEHICLE SECURITY SYSTEM
SEC-255
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Component Parts Location
INFOID:0000000003508922
1.
BCM M118, M119, M121, M122, M123
2.
TCM F23
3.
IPDM E/R E10, E11, F12
4.
ECM E16
5.
Push-button ignition switch M101
6.
Key slot M99
7.
Combination meter (key warning lamp)
M34
8.
Security indicator lamp M100
9.
Horn (high) E340, E341
10. Horn (low) E342, E343
11.
Control device (detection switch) M57
12. Stop lamp switch
TYPE A: E115
TYPE B: E116
13. Remote keyless entry receiver
A.
Behind the combination meter
B.
Engine room (LH)
C.
View with the center console as-
sembly removed
D.
Behind the instrument lower panel LH
E.
Behind the instrument lower panel RH
JMKIA1825ZZ
Revision: 2008 October
2009 Murano
SEC-256
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM
Component Description
INFOID:0000000003465858
1.
Back door lock assembly (back door
switch) D180
2.
Front door switch (driver side) B34
3.
Power window main switch (door
lock and unlock switch) D5, D6
4.
Front power window switch (passen-
ger side) D45
JMKIA1913ZZ
Component Reference
BCM
Horn relay 1
Horn relay 2
Security indicator
Door switch
Back door lock assembly (back door witch)
Door key cylinder switch
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
SEC-257
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000003566304
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: At models with Intelligent Key system this item is displayed, but is not used.
• *2: At models with rain sensor this mode is displayed, but is not used.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT*
1
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
*
2
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
3
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
Revision: 2008 October
2009 Murano
SEC-258
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
• *3: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000003671442
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
SEC-259
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
WORK SUPPORT
SELF-DIAG RESULT
.
DATA MONITOR
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Description
REMO CONT ID CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode.
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from the
following with this mode.
• MODE 1: 0.5 sec.
• MODE 2: Non-operation
• MODE 3: 1.5 sec.
PW DOWN SET
Unlock button pressing time on Intelligent Key button can be selected from the following with this
mode.
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 sec.
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be supported.
SHORT CRANKING OUTPUT
Starter motor can operate during the times below.
• 70 msec
• 100 msec
• 200 msec
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis.
Monitor Item
Condition
REQ SW -DR
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -AS
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RR
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RL
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -BD/TR
NOTE:
This item is displayed, but cannot be monitored.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY2 -F/B
Indicates [ON/OFF] condition of ignition relay 2.
ACC RLY-FB
NOTE:
This item is displayed, but cannot be monitored.
CLUCH SW
NOTE:
This item is displayed, but cannot be monitored.
Revision: 2008 October
2009 Murano
SEC-260
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
BRAKE SW 1
Indicates [ON/OFF]*
1
condition of brake switch power supply.
BRAKE SW 2
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of P position.
SFT PN/N SW
Indicates [ON/OFF] condition of P or N position.
S/L -LOCK
Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY -F/B
Indicates [ON/OFF] condition of ignition switch.
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 -F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position.
SFT P -MET
Indicates [ON/OFF] condition of P position.
SFT N -MET
Indicates [ON/OFF] condition of N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock unit (LOCK).
S/L UNLK-IPDM
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLOCK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.
ID OK FLAG
Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from keyfob.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from keyfob.
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of keyfob.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from keyfob.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from keyfob.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on keyfob, the numer-
ical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
Condition
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
SEC-261
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
MULTIREMOTE ENT
MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTI REMOTE ENT)
INFOID:0000000003737109
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “B&P N” on CONSULT-III screen is touched.
• Engine start information displays when “B&P I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is touched.
• Take away warning display when “OUTKY” on CONSULT-III screen is touched.
• OFF position warning display when “LK WN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCH
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.
IGN CONT2
This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT-III screen is touched.
P RANGE
This test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDICATOR
NOTE:
This item is displayed, but cannot be tested.
ACC INDICATOR
This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON IND
This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
AUTOMATIC SLIDING DOOR
NOTE:
This item is displayed, but cannot be tested.
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Revision: 2008 October
2009 Murano
SEC-262
< FUNCTION DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Monitor Item
Condition
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of door lock and unlock switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from keyfob.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from keyfob.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from keyfob.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of keyfob.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from keyfob.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from keyfob.
KEY CYL LK-SW
Indicated [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicated [ON/OFF] condition of unlock signal from door key cylinder.
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored.
Test item
Description
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LUGGAGE LAMP TEST
NOTE:
This item is displayed, but cannot be tested.
DOOR LOCK
This test is able to check door lock/unlock operation.
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched.
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is
touched.
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen
is touched.
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT- III
screen is touched.
• The door lock actuator (rear LH and RH) is unlocked when “OTR ULK” on CONSULT-III
screen is touched.
FLASHER
This test is able to check flasher operation [LH/RH/OFF].
HORN
This test is able to check horn operation [ON/OFF].
TRUNK/GLASS HATCH
This test is able to check trunk lid opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
AUTOMATIC BACK DOOR
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст