Nissan Murano Z50 (2004 year). Manual — part 131

GW-32

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

7.

Select diagnosis mode.
“ACTIVE TEST” and “WORK SUPPORT” are available.

ACTIVE TEST

WORK SUPPORT

DATA MONITOR

SEL274W

Test Item

Description

RETAINED PWR

This test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-II screen even if the ignition switch is turned OFF.

NOTE:
During this test, CONSULT-II can be operated with ignition switch in “OFF” position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-II screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-II might be stuck if
“RETAINED PWR” is turned to “ON” or “OFF” on CONSULT-II screen when ignition switch is OFF.

POWER WINDOW DOWN

This test able to transmitted of power window down signal from BCM to power window main switch
and front power window switch (passenger side).

Work item

Description

RETAINED PWR

RAP signal’s power supply period can be changed by mode setting. Selects RAP signal’s power
supply period between three steps

●

MODE1 (45 sec.) / MODE2 (OFF) / MODE 3 (2 min.).

Work item

Description

IGN ON SW

Indicates (ON / OFF) condition of ignition switch

DOOR SW–DR

Indicates (ON / OFF) condition of front door switch driver side

DOOE SW–AS

Indicates (ON / OFF) condition of front door switch passenger side

LOCK SW DR/AS

Indicates (ON / OFF) condition of lock signal from lock and unlock switch on power window main
switch or front power window switch (passenger side).

UNLK SW DR/AS

Indicates (ON / OFF) condition of unlock signal from lock and unlock switch on power window
main switch or front power window switch (passenger side).

KEY CYL LK-SW

Indicates (ON / OFF) condition of lock signal from key cylinder.

KEY CYL UN-SW

Indicates (ON / OFF) condition of unlock signal from key cylinder.

POWER WINDOW SYSTEM

GW-33

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

Trouble Diagnosis Symptom Chart

AIS002D1

●

Make sure other systems using the signal of the following systems operate normally.

Symptom

Repair order

Refer to page

None of the power windows can be operated using any switch.

1. BCM power supply and ground circuit check

GW-34

2. Power window main switch power supply
and ground circuit check

GW-35

3. Power window serial link check

GW-55

4. Replace BCM.

BCS-14

Driver side power window alone does not operate.

1. Power window motor (driver side) circuit
check

GW-37

2. Replace power window main switch

EI-30

Front passenger side power window alone does not operate.

1. Front power window switch (passenger side)
power and ground circuit check

GW-36

2. Power window serial link check

GW-55

3. Front power window motor (passenger side)
circuit check

GW-38

4. Replace BCM.

BCS-14

Rear LH side power window alone does not operate.

1. Rear power window motor (LH) circuit check

GW-38

Rear RH side power window alone does not operate.

1. Rear power window motor (RH) circuit check

GW-40

Anti-pinch system does not operate normally (driver side).

1. Door window sliding part malfunction

●

A foreign material adheres to window glass
or glass run rubber.

●

Glass run rubber wear or deformation.

●

Sash is tilted too much, or no enough.

—

2. Limit switch adjusting

GW-60

3. Limit switch circuit check (driver side)

GW-42

4. Encoder circuit check (driver side)

GW-46

Anti-pinch system does not operate normally (passenger side).

1. Door window sliding part malfunction

●

A foreign material adheres to window glass
or glass run rubber.

●

Glass run rubber wear or deformation.

●

Sash is tilted too much, or no enough.

—

2. Limit switch adjusting

GW-60

3. Limit switch circuit check (passenger side)

GW-44

4. Encoder circuit check (passenger side)

GW-48

Power window retained power operation does not operate prop-
erly.

1. Check the retained power operation mode
setting.

GW-32

2. Door switch check

GW-51

3. Replace BCM.

BCS-14

Does not operate by key cylinder switch.

1. Door key cylinder switch check

GW-53

2. Replace power window main switch

EI-30

Power window lock switch does not function.

1. Power window serial link check

GW-55

2. Power window lock switch check

GW-57

Auto operation does not operate but manual operate normally.
(driver side)

1. Encoder circuit check (driver side)

GW-46

2. Replace power window main switch

EI-30

Auto operation does not operate but manual operate normally.
(passenger side)

1. Encoder circuit check (passenger side)

GW-48

2. Replace front power window switch (passen-
ger side)

EI-30

GW-34

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

BCM Power Supply and Ground Circuit Check

AIS002D3

1.

CHECK FUSE

●

Check 10A fuse [No.1, located in fuse block (J/B)]

●

Check 10A fuse [No.18, located in fuse block (J/B)]

●

Check 50A fusible link (letter F located in the fuse and fusible link box)

NOTE:
Refer to

GW-17, "Component Parts and Harness Connector Location"

OK or NG

OK

>> GO TO 2.

NG

>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to

PG-

3, "POWER SUPPLY ROUTING CIRCUIT"

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch ON.

2.

Check voltage between BCM connector M34, M35 terminal 38,
42, 55 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Check BCM power supply circuit for open or short.

3.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM connector M35 terminal 52 and
ground.

OK or NG

OK

>> BCM power supply and ground circuit is OK.

NG

>> Check BCM ground circuit for open or short.

38 (R) – Ground

: Battery voltage

42 (GR) – Ground

: Battery voltage

55 (W/B) – Ground

: Battery voltage

PIIA6160E

52 (B) – Ground

: Continuity should exist.

PIIA9131E

POWER WINDOW SYSTEM

GW-35

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

Power Window Main Switch Power Supply Circuit Check

AIS002D5

1.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch ON.

2.

Check voltage between power window main switch connector
D6, D7 terminals 10, 19 and ground.

OK or NG

OK

>> Power window main switch power supply and ground

circuit is OK.

NG

>> GO TO 2.

2.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch connector
D7 terminal 17 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness.

3.

CHECK HARNESS CONTINUITY

1.

Disconnect BCM connector.

2.

Check continuity between BCM connector M35 terminals 53, 54
and power window main switch connector D6, D7 terminal 10,
19.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace harness between BCM and power

window main switch.

10 (W/L) – Ground

: Battery voltage

19 (W/R) – Ground

: Battery voltage

PIIA4171E

17 (B) – Ground

: Continuity should exist.

PIIA4172E

53 (W/L) – 10 (W/L)

: Continuity should exist.

54 (W/R) – 19 (W/R)

: Continuity should exist.

PIIA6280E

GW-36

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

4.

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Turn ignition switch ON.

3.

Check voltage between BCM connector M35 terminal 53, 54
and ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace BCM.

Front Power Window Switch (Passenger Side) Power Supply and Ground Cir-
cuit Check

AIS002D6

1.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch ON.

2.

Check voltage between front power window switch (passenger
side) connector D35 terminal 10 and ground.

OK or NG

OK

>> Front power window switch (passenger side) power sup-

ply and ground circuit is OK.

NG

>> GO TO 2.

2.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector.

3.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 11 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness.

53 (W/L) – Ground

: Battery voltage

54 (W/R) – Ground

: Battery voltage

PIIA6154E

10 (W/R) – Ground

: Battery voltage

PIIA4174E

11 (B) – Ground

: Continuity should exist.

PIIA4175E

POWER WINDOW SYSTEM

GW-37

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

3.

CHECK HARNESS CONTINUITY

1.

Disconnect BCM connector.

2.

Check continuity between BCM connector M35 terminal 54 and
front power window switch (passenger side) connector D35 ter-
minal 10.

3.

Check continuity between BCM connector M35 terminal 54 and
ground.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Repair or replace harness between BCM and front

power window switch (passenger side).

Front Power Window Motor (Driver Side) Circuit Check

AIS002D8

1.

CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL

1.

Turn igniting switch ON.

2.

Check voltage between power window main switch connector D6 terminals 8, 11 and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Replace power window main switch.

2.

CHECK HARNESS CONITNUITY

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch and front power window motor (driver side) connector.

3.

Check continuity between power window main switch connector
D6 terminal 8, 11 and front power window motor (driver side)
connector D8 terminals 1,2.

OK or NG

OK

>> Replace front power window motor (driver side).

NG

>> Repair or replace harness between power window main

switch and front power window motor (driver side).

54 (W/R) – 10 (W/R)

: Continuity should exist.

54 (W/R) – Ground

: Continuity should not exist.

PIIA6281E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D6

8 (G/R)

Ground

Closing

Battery voltage

Opening

0

11 (G/W)

Closing

0

Opening

Battery voltage

PIIA4179E

8 (G/R) – 2 (G/R)

: Continuity should exist.

11 (G/W) – 1 (G/W)

: Continuity should exist.

PIIA9658E

GW-38

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

Front Power Window Motor (Passenger Side) Circuit Check

AIS002DA

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) OUTPUT SIGNAL

1.

Turn igniting switch ON.

2.

Check voltage between front power window switch (passenger side) connector D35 terminals 8, 9 and
ground.

OK or NG

OK

>> GO TO 2.

NG

>> Replace front power window switch (passenger side).

2.

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) and front power window motor (passenger side)
connector.

3.

Check continuity between front power window switch (passen-
ger side) connector D35 terminals 8,9 and front power window
motor (passenger side) connector D36 terminals 1, 2.

OK or NG

OK

>> Replace front power window motor (passenger side).

NG

>> Repair or replace harness between front power window

switch (passenger side) and front power window motor
(passenger side).

Rear Power Window Motor (LH) Circuit Check

AIS002DB

1.

CHECK REAR POWER WINDOW SWITCH (LH) OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window motor (LH).

3.

Turn ignition switch ON.

4.

Check voltage between rear power window motor (LH) connector D52 terminals 1, 2 and ground.

OK or NG

OK

>> Replace rear power window motor (LH).

NG

>> GO TO 2.

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D35

8 (L)

Ground

Closing

Battery voltage

Opening

0

9 (G)

Closing

0

Opening

Battery voltage

PIIA4182E

8 (L) – 2 (L)

: Continuity should exist.

9 (G) – 1 (G)

: Continuity should exist.

PIIA9659E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D52

1 (G)

Ground

Closing

0

Opening

Battery voltage

2 (L)

Closing

Battery voltage

Opening

0

PIIA9660E

POWER WINDOW SYSTEM

GW-39

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

2.

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch (LH) connector.

3.

Check continuity between rear power window switch (LH) con-
nector D55 terminal 4, 5 and rear power window motor (LH) con-
nector D52 terminals 1, 2.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between rear power window

switch (LH) and rear power window motor (LH).

3.

CHECK REAR POWER WINDOW SWITCH (LH) POWER SUPPLY

1.

Connect rear power window switch (LH) connector.

2.

Turn ignition switch ON.

3.

Check voltage between rear power window switch (LH) connec-
tor D55 terminal 1 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace harness.

4.

CHECK REAR POWER WINDOW SWITCH LH

1.

Turn igniting switch OFF.

2.

Disconnect rear power window switch (LH) connector.

3.

Check continuity between rear power window switch (LH) connector D55 terminals 1, 2, 3 and 4, 5.

OK or NG

OK

>> GO TO 5.

NG

>> Replace rear power window switch (LH).

4 (G) – 1 (G)

: Continuity should exist.

5 (L) – 2 (L)

: Continuity should exist.

PIIA9661E

1 (W/L) – Ground

: Battery voltage

PIIA4185E

Terminal

Switch condition

Continuity

1

4

DOWN position

Yes

3

Free

1

5

UP position

2

Free

PIIA4186E

GW-40

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

5.

CHECK POWER WINDOW MAIN SWITCH OUTPUT SINGAL

1.

Turn ignition switch ON.

2.

Power window main switch is operated, check voltage between power window main switch connector D6
terminals 1, 3 and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Replace power window main switch.

6.

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch connector
D6 terminals 1, 3 and rear power window switch (LH) connector
D55 terminals 2, 3.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Repair or replace harness between power window main

switch and rear power window switch (LH).

Rear Power Window Motor (RH) Circuit Check

AIS002DC

1.

CHECK REAR POWER WINDOW SWITCH (RH) OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window motor (RH).

3.

Turn ignition switch ON.

4.

Check voltage between rear power window motor (RH) connector D72 terminal 1, 2 and ground.

OK or NG

OK

>> Replace rear power window motor (RH).

NG

>> GO TO 2.

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D6

1 (Y)

Ground

Closing

Battery voltage

Opening

0

3 (R)

Closing

0

Opening

Battery voltage

PIIA4187E

1 (Y) – 2 (Y)

: Continuity should exist.

3 (R) – 3 (R)

: Continuity should exist.

PIIA4188E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D72

1 (G)

Ground

Closing

0

Opening

Battery voltage

2 (L)

Closing

Battery voltage

Opening

0

PIIA9660E

POWER WINDOW SYSTEM

GW-41

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

2.

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch (RH) connector.

3.

Check continuity between rear power window switch (RH) con-
nector D75 terminals 4, 5 and rear power window motor (RH)
connector D72 terminal 1, 2.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace harness between rear power window

switch (RH) and rear power window motor (RH).

3.

CHECK REAR POWER WINDOW SWITCH (RH) POWER SUPPLY

1.

Connect rear power window switch (RH) connector.

2.

Turn ignition switch ON.

3.

Check voltage between rear power window switch (RH) connec-
tor D75 terminal 1 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace harness.

4.

CHECK REAR POWER WINDOW SWITCH (RH)

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch (RH) connector.

3.

Check continuity between rear power window switch (RH) con-
nector D75 terminal 1, 2, 3 and 4, 5.

OK or NG

OK

>> GO TO 5.

NG

>> Replace rear power window switch (RH).

4 (G) – 1 (G)

: Continuity should exist.

5 (L) – 2 (L)

: Continuity should exist.

PIIA9661E

1 (W/L) – Ground

: Battery voltage

PIIA4185E

Terminal

Switch condition

Continuity

1

4

DOWN position

Yes

3

Free

1

5

UP position

2

Free

PIIA4186E

GW-42

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

5.

CHECK POWER WINDOW MAIN SWITCH OUTPUT SINGAL

1.

Turn ignition switch ON.

2.

Power window main switch is operated, check voltage between power window main switch connector D6
terminals 5, 7 and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Replace power window main switch.

6.

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch connector
D6 terminal 5, 7 and rear power window switch (RH) connector
D75 terminal 2, 3.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Repair or replace harness between power window main

switch and rear power window switch (RH).

Limit Switch Circuit Check (Driver Side)

AIS002DF

1.

CHECK DRIVER DOOR MAIN SWITCH LIMIT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (driver side) connector and ground.

OK or NG

OK

>> Limit switch circuit is OK.

NG

>> GO TO 2.

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D6

5 (R)

Ground

Closing

0

Opening

Battery voltage

7 (Y/B)

Closing

Battery voltage

Opening

0

PIIA4189E

5 (R) – 3 (R)

: Continuity should exist.

7 (Y/B) – 2 (Y/B)

: Continuity should exist.

PIIA4190E

Connector

Terminals (Wire color)

Condition Voltage

(V)

(Approx.)

(+)

(-)

D8

5 (G/W)

Ground

Driver side door window is
between fully-open and just
before fully-closed position
(ON)

0

Driver side door window is
between just before fully-
closed position and fully-
closed position (OFF)

5

PIIA9662E

POWER WINDOW SYSTEM

GW-43

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

2.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Check continuity between front power window motor (driver
side) connector D8 terminal 6 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 3.

3.

CHECK HARNESS CONTINUITY 1

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminal 2 and front power window motor (driver side) con-
nector D8 terminal 6.

OK or NG

OK

>> Replace power window main switch.

NG

>> Repair or replace harness between power window main

switch and front power window motor (driver side).

4.

CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between power window main switch connector
D6 terminal 9 and ground.

OK or NG

OK

>> GO TO 5.

NG

>> Replace power window main switch.

6 (W/B) – Ground

: Continuity should exist.

PIIA9663E

2 (W/B) – 6 (W/B)

: Continuity should exist.

PIIA9664E

9 (G/W) – Ground

: Approx. 5V

PIIA4194E

GW-44

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

5.

CHECK HARNESS CONTINUITY 2

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch connector
D6 terminal 9 and front power window motor (driver side) con-
nector D8 terminal 5.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace harness between and power window

main switch front power window motor (driver side).

6.

CHECK LIMIT SWITCH

1.

Connect power window main switch and front power window motor (driver side) connector.

2.

Turn ignition switch ON.

3.

Check continuity between front power window motor (driver
side) connector D8 terminals 5 and 6.

*: When checking continuity, turn ignition switch OFF.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace front power window motor (driver side).

Limit Switch Circuit Check (Passenger Side)

AIS002DH

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) LIMIT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (passenger side) connector and ground.

OK or NG

OK

>> Limit switch circuit is OK.

NG

>> GO TO 2.

9 (G/W) – 5 (G/W)

: Continuity should exist.

PIIA9665E

Connector

Terminals (Wire color)

Condition

Continuity

D8

5 (G/W)

6 (W/B)

Driver side door window is
between fully-open and just
before fully-closed position
(ON)

Yes*

Driver side door window is
between just before fully-
closed position and fully-
closed position (OFF)

No*

PIIA9666E

Connector

Terminals (Wire color)

Condition

Voltage (V)

(Approx.)

(+)

(-)

D36

5 (G/W)

Ground

Passenger side door window
is between fully-open and
just before fully-closed posi-
tion (ON)

0

Passenger side door window
is between just before fully-
closed position and fully-
closed position (OFF)

5

PIIA9667E

POWER WINDOW SYSTEM

GW-45

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

2.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (passenger side) connector.

3.

Check continuity between front power window motor (passenger
side) connector D36 terminal 6 and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 3.

3.

CHECK HARNESS CONTINUITY 1

1.

Disconnect front power window switch (passenger side) connector.

2.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 3 and front power window
motor (passenger side) connector D36 terminal 6.

OK or NG

OK

>> Replace front power window switch (passenger side).

NG

>> Repair or replace harness between front power window

switch (passenger side) and front power window motor
(passenger side).

4.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between front power window switch (passenger
side) connector D35 terminal 15 and ground.

OK or NG

OK

>> GO TO 5.

NG

>> Replace front power window switch (passenger side).

6 (W/B) – Ground

: Continuity should exist.

PIIA9668E

3 (W/B) – 6 (W/B)

: Continuity should exist.

PIIA9669E

15 (G/W) – Ground

: Approx. 5V

PIIA4200E

GW-46

POWER WINDOW SYSTEM

Revision: 2004 November

2004 Murano

5.

CHECK HARNESS CONTINUITY 2

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector.

3.

Check continuity between front power window switch (passen-
ger side) connector D35 terminal 15 and front power window
motor (passenger side) connector D36 terminal 5.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace harness between front power window

switch (passenger side) and front power window motor
(passenger side).

6.

CHECK LIMIT SWITCH

1.

Connect front power window motor (passenger side) and front power window switch (passenger side)
connector.

2.

Turn ignition switch ON.

3.

Check continuity between front power window motor (passenger
side) connector D36 terminals 5 and 6.

*: When checking continuity, turn ignition switch OFF.

OK or NG

OK

>> Check the condition of the harness and the connector.

NG

>> Replace front power window motor (passenger side).

Encoder Circuit Check (Driver Side)

AIS002DJ

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) POWER SUPPLY

1.

Turn ignition switch ON.

2.

Check voltage between front power window motor (driver side)
connector D8 terminal 4 and ground.

OK or NG

OK

>> GO TO 3.

NG

>> GO TO 2.

15 (G/W) – 5 (G/W)

: Continuity should exist.

PIIA9670E

Connector

Terminals (Wire color)

Condition

Continuity

D36

5 (G/W)

6 (W/B)

Passenger side door window
is between fully-open and
just before fully-closed posi-
tion (ON)

Yes*

Passenger side door window
is between just before fully-
closed position and fully-
closed position (OFF)

No*

PIIA9671E

4 (G/R) – Ground

: Approx.10V

PIIA9672E

POWER WINDOW SYSTEM

GW-47

C

D

E

F

G

H

J

K

L

M

A

B

GW

Revision: 2004 November

2004 Murano

2.

CHECK HARNESS CONTINUITY 1

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) and power window main switch.

3.

Check continuity between power window main switch connector
D6 terminal 15 and front power window motor (driver side) con-
nector D8 terminal 4.

OK or NG

OK

>> Replace power window main switch.

NG

>> Repair or replace harness between power window main

switch connector and front power window motor (driver
side) connector.

3.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Check continuity between front power window motor (driver
side) connector D8 terminal 6 and round.

OK or NG

OK

>> GO TO 5.

NG

>> GO TO 4.

4.

CHECK HARNESS CONTINUITY 2

1.

Disconnect power window main switch connector.

2.

Check continuity between power window main switch connector
D6 terminal 2 and front power window motor (driver side) con-
nector D8 terminal 6.

OK or NG

OK

>> Replace power window main switch.

NG

>> Repair or replace harness between power window main

switch and front power window motor (driver side).

15 (G/R) – 4 (G/R)

: Continuity should exist.

PIIA9673E

6 (W/B) – Ground

: Continuity should exist.

PIIA9663E

2 (W/B) – 6 (W/B)

: Continuity should exist.

PIIA9664E