Fiat Qubo (2021 year). Manual in english — page 10
155
REPLACING AN
EXTERIOR BULB
For the type of bulb and relevant power
rating, see the “Changing a bulb”
paragraph.
FRONT LIGHT CLUSTERS
The front light clusters fig. 193 contain
sidelight, dipped beam, main beam and
direction indicator bulbs.
The bulbs are arranged inside the light
cluster as follows:
(A) Side lights/tail lights and
main/dipped beam headlights;
(B) Direction indicators.
193
F0T0093
SIDE LIGHTS
To replace the bulb, proceed as
follows:
remove the protective cover (A)
fig. 193;
turn the bulb holder (A) fig. 194
anticlockwise and extract it;
extract the bulb (B) and replace it;
refit the new bulb, put the bulb
holder (A) fig. 194 back into place
and then refit the protective cover (A)
fig. 193 properly.
194
F0T0094
DIPPED BEAM/MAIN
BEAM HEADLIGHTS
To change the bulb (double filament),
proceed as follows:
remove the protective cover (A)
fig. 193;
release the bulb holder clip;
extract the bulb (A) fig. 195 from the
connector (B) and replace it;
195
F0T0095
refit the new bulb by inserting it on
connector (B) and then make the
contour of the metallic part mate with
the grooves obtained on the headlight
parabola;
refit the bulb holder clip and refit the
protective lid (A) fig. 193.
DIRECTION INDICATORS
Front
To replace the bulb, proceed as
follows:
turn the protective lid (B) fig. 193
anticlockwise;
extract the bulb (A) fig. 196 and
replace it;
correctly refit the protective cover (B).
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
156
196
F0T0096
Side
To replace the bulb, proceed as
follows:
adjust the lens (A) fig. 197 to
compress in the clip (B) fig. 198, then
pull the cluster outwards;
turn the bulb holder (C)
anticlockwise, extract the press-fit bulb
(D) and replace it;
refit the bulb holder (C) in the lens
and turn it clockwise;
refit the cluster making sure that the
internal clip (B) clicks into position.
197
F0T0097
198
F0T0098
FOG LIGHTS
(for versions/markets, where provided)
WARNING Contact Fiat Dealership to
replace the front fog lights.
REAR LIGHT CLUSTERS
The rear light clusters contain the bulbs
for the side lights, direction indicators
and reversing/rear fog and brake lights.
To access the light clusters, proceed
as follows:
open the rear swing doors;
loosen the screws (A) fig. 200 as to
access the light cluster (B) fig. 199;
remove the connector (C) fig. 199.
199
F0T0100
-------------------------------------------------------------------------------------------------------------------------------------------------------------
157
200
F0T0099
The bulbs are arranged inside the light
cluster fig. 201 and fig. 202 as follows:
A
Brake lights;
B
Direction indicators;
C
Reverse lights;
D
Side/rear fog lights.
Pull the 5 tabs (E) fig. 201 outwards to
access the bulbs.
201
F0T0101
202
F0T0102
THIRD BRAKE LIGHTS
Fiorino versions with swing door
Contact Fiat Dealership to replace the
third brake lights fig. 203.
203
F0T0103
Qubo versions with tailgate
To replace the bulbs, proceed as
follows fig. 204 - fig. 205:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
158
204
F0T0212
A
C
A
B
205
F0T0443
open the tailgate and loosen the two
retaining screws (A);
disconnect the electrical connector
(B);
release the retainer tab (C) and open
the bulb holder assembly;
extract the snap-fitted bulb and
replace it
NUMBER PLATE LIGHTS
To replace the bulbs (A) fig. 206,
proceed as follows:
206
F0T0104
operate the holding tabs at the points
indicated by the arrows, and remove
the bulb holder;
207
F0T0105
turn the bulb holder (B) fig. 207
anticlockwise, then remove bulb (C).
REPLACING
INTERIOR BULBS
For the type of bulb and relevant power
rating, see “Changing a bulb”.
FRONT CEILING LIGHT
Ceiling light with movable lens
To replace the bulbs, proceed as
follows:
208
F0T0106
extract the ceiling light (A) fig. 208 by
operating in the points shown by the
arrows;
open the lid (B) fig. 209 as shown;
remove bulb (C) fig. 209 by releasing
it from the side contacts, then insert
the new bulb and make sure it is
correctly clamped between these
contacts;
close the lid and secure the ceiling
light into its housing, making sure it
locks properly into place.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
159
209
F0T0458
Front ceiling light with map reading
lights
(for versions/markets, where provided)
To replace the bulbs, proceed as
follows:
210
F0T0143
operate in the points shown by the
arrow and remove ceiling light (A)
fig. 210;
open protective flap (B) fig. 211;
replace the bulbs (C) by releasing
them from the side contacts and
making sure that the new bulbs
are correctly secured between the
contacts;
re-close the flap (B) fig. 211 and
fasten the ceiling light (A) fig. 210 in its
housing, making sure that it locks into
place.
211
F0T0144
REAR CEILING LIGHT
Fiorino Cargo versions
To replace the bulb, proceed as
follows:
extract the ceiling light (A) fig. 212 by
operating in the points shown by the
arrows;
open the lid (B) fig. 213 as shown;
212
F0T0107
remove bulb (C) fig. 213 by releasing
it from the side contacts, then insert
the new bulb and make sure it is
correctly clamped between these
contacts;
close the cover (B) fig. 213 and
secure the ceiling light into its housing,
making sure it locks properly into place;
close the cover (B) and secure the
ceiling light into its housing, making
sure it locks properly into place.
213
F0T0458
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
160
REMOVABLE CEILING
LIGHT
(for versions/markets, where provided)
To replace the bulb, proceed as
follows:
press button (A) fig. 214 and extract
the removable courtesy light (B);
extract the ceiling light by operating
in the points shown by the arrows;
change the bulb (C) fig. 215 releasing
it from the side contacts and making
sure the new bulb is correctly fastened
between the contacts;
AUTO
214
F0T0108
AUTO
215
F0T0109
BOOT COURTESY LIGHT
(for versions/markets, where provided)
To change the bulb, proceed as
follows:
open the tailgate;
remove the light (A) fig. 216 levering
in the point shown by the arrow.
open the protection (B) replace the
snap-fitted bulb;
close the cover (B) on the lens;
refit the ceiling light (A) by inserting it
in its correct position firstly on one side
and then pressing on the other until it
clicks into place.
216
F0T0251
FUSE
REPLACEMENT
GENERAL INFORMATION
For fuse replacement, contact a Fiat
Dealership.
135) 136) 137) 138) 139) 140)
30)
Fuses protect the electrical system:
they intervene (blow) in the event of
a failure or improper action on the
system.
Check the state of the corresponding
fuse when a device does not work: the
filament (A) fig. 217 should be intact.
If it is not, replace the blown fuse with
another with the same ampere rating
(same colour).
(B) intact fuse.
(C) fuse with damaged filament.
To change a fuse, use the tongs (D)
located in the tool box or the Fix&Go
container (for versions/markets where
provided).
Refer to the tables on the following
pages to identify the protective fuse.
WARNING The Natural Power system
components are protected by specific
fuses. Contact a Fiat Dealership for
replacement.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
161
217
F0T0015
ENGINE BAY FUSE BOX
The fuse box is on the right-hand side
of the engine.
Removing the fuse box lid
218
F0T0171
Proceed as follows:
remove protective cover (A) fig. 218
the positive battery terminal by lifting it
upwards;
219
F0T0172
press the tab (A) fig. 219 and remove
the fuse box protective cover (B);
move the cover towards the
headlight, turning it anticlockwise (as
shown by the arrow) and then remove
it fig. 220;
the fuse box can be accessed in this
manner fig. 222.
31)
220
F0T0173
Refitting the fuse box lid
Proceed as follows to refit the lid:
insert the two tabs (A) fig. 221 in the
respective seats located on the fuse
box;
refasten the tab (B) in the
corresponding seat until it clicks.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
162
221
F0T0174
135)
For fuse replacement, contact a Fiat
Dealership.
136)
If the replaced fuse blows again,
contact a Fiat Dealership.
137)
Never replace a fuse with another
with a higher amp rating; RISK OF FIRE.
138)
If a general fuse (MEGA-FUSE, MIDI-
FUSE, MAXI-FUSE) blows contact a Fiat
Dealership.
139)
Before replacing a fuse, make sure
that the ignition key has been removed
and that all the other services are switched
off and/or disengaged.
140)
Contact Fiat Dealership if a safety
system (airbags, brakes), engine system
(engine, transmission) or steering system
general protection fuse blows.
30)
Never replace a faulty fuse with metal
wires or anything else.
31)
If you need to clean the engine
compartment, take care not to directly hit
the fuse box with the water jet.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
163
222
F0T0181
PROTECTED DEVICE
FUSE
AMPERE
Spare (trailer kit)
F09
10
Horns
F10
10
Main beam headlights
F14
15
Rear power socket
F15
15
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
164
PROTECTED DEVICE
FUSE
AMPERE
Climate control compressor
F19
7.5
Heated rear window, mirror defrosters
F20
30
Fuel pump
F21
15
Fog lights
F08
15
Cigar lighter/Passenger compartment socket/Heated
seats/USB APO
F85
30
IBS battery charge sensor for Start&Stop system (1.3
Multijet Euro 6 with Start&Stop)
F87
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
165
PASSENGER
COMPARTMENT FUSE
BOX
To access to the fuses loosen the two
screws (A) fig. 223 using the metallic
insert of ignition key and then remove
the flap (B).
223
F0T0178
The fuses are positioned in the two
areas shown in fig. 224.
224
F0T0183
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
166
PROTECTED DEVICE
FUSE
AMPERE
Dipped headlight (passenger side)
F12 (*)
7.5
Dipped headlight (driver side)/Headlight adj.
F13
7.5 / 5 (*)
INT/A SCM relay coils
F31
5
Timed interior lighting
F32 (*)
7.5
Radio node/
Bluetooth®
system control unit /EOBD
system control unit/Volumetric alarm control unit/Alarm
siren control unit
F36
10
Instrument panel node/Stop light control (NO)
F37
5
Door/boot lock actuators (*)
F38
20
Windscreen washer/rear window washer bidirectional
pump
F43
15
Front electric window (driver side) (*)
F47
20
Front electric window (passenger side) (*)
F48
20
Controls lighting/Parking sensors control unit/Electric wing
mirrors control/Volumetric alarm control unit
F49
5
INT Radio node/
Bluetooth®
system control unit /Electric
mirror movement/Clutch switch/Brake lights (NC)
F51
7.5
Instrument panel node
F53
5
Door mirror defrosters
F41
7.5
Free
F45
–
-------------------------------------------------------------------------------------------------------------------------------------------------------------
167
PROTECTED DEVICE
FUSE
AMPERE
Free
F46
–
Free
F90
–
Free
F91
–
Free
F92
–
Free
F93
–
Cigar lighter/Passenger compartment power socket
F94
15
Free
F95
–
Cigar lighter/Passenger compartment power socket
F96
15
Front seat heater (driver side)
F97
7.5 (**)/10 (***)
Front seat heater (passenger side)
F98
7.5 (**)/10 (***)
(*) For versions/markets where provided
(**) Left-hand drive versions
(***) Right-hand drive versions
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
168
EMERGENCY
STARTING
Go to a Fiat Dealership immediately if
warning light
comes on steady on
the instrument panel.
JUMP STARTING
If the battery is flat, it is possible to start
the engine using an auxiliary battery
with the same capacity or a little higher
than the flat one.
Proceed as follows to start the engine
fig. 225:
connect the positive terminals (+
mark near the terminal) of the two
batteries using a suitable lead;
with a second lead, connect the
negative terminal (-) of the auxiliary
battery to an earthing point
on the
engine or the gearbox of the vehicle to
be started;
start the engine;
when the engine has been started,
remove the leads reversing the order
above.
If after a few attempts the engine does
not start, do not persist but contact the
nearest Fiat Dealership.
141)
32)
225
F0T0189
WARNING Do not directly connect
the negative terminals of the two
batteries: sparks could ignite explosive
gas released from the battery. If the
auxiliary battery is installed on another
vehicle, avoid any metal parts on the
latter and the vehicle with the flat
battery from accidentally coming into
contact.
BUMP STARTING
Never bump start the engine by
pushing, towing or driving downhill.
This could cause fuel to flow into the
catalytic converter and damage it
beyond repair.
WARNING Remember that the brake
booster and the power steering
system are not active until the engine
is started, so you will need to apply
much more force to the brake pedal or
steering wheel.
141)
This starting procedure must be
performed by expert personnel because
incorrect actions could cause electrical
discharge of considerable intensity.
Furthermore, battery fluid is poisonous
and corrosive: avoid contact with skin and
eyes. Keep naked flames and lighted
cigarettes away from the battery and do
not cause sparks.
32)
Never use a fast battery charger to
start the engine as this could damage the
electronic systems, particularly the engine
ignition and fuel supply control units.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
169
FUEL CUT-OFF
SYSTEM
142)
This intervenes in the case of an impact
causing:
the interruption of the fuel supply with
the engine consequently cutting out;
the automatic unlocking of the doors;
turning on the lights inside the car;
closing of the methane system safety
solenoid valves (for versions/markets,
where provided).
When the system has been triggered,
the message “Fuel cut-off see
handbook” is displayed on some
versions.
WARNING Check carefully for fuel
leaks, for instance in the engine
compartment, under the vehicle or near
the tank area. After a crash, turn the
ignition key to STOP to avoid draining
the battery.
The following procedure should be
carried out to restore the correct
operation of the vehicle:
turn the ignition key to MAR;
activate the right direction indicator;
deactivate the right direction
indicator;
activate the left direction indicator;
deactivate the left direction indicator;
activate the right direction indicator;
deactivate the right direction
indicator;
activate the left direction indicator;
deactivate the left direction indicator;
turn the ignition key to STOP.
142)
If, after an impact, you smell fuel or
notice leaks from the fuel system, do not
reactivate the system to avoid the risk of
fire.
TOWING THE
VEHICLE
The tow ring provided with the vehicle
is located in the tool box behind the left
seat backrest (Fiorino Cargo versions)
or in the luggage compartment (Qubo
and Fiorino Combi versions).
ATTACHING THE TOW
HOOK
Proceed as follows:
release the cap (A) fig. 226 (Fiorino
versions), fig. 227 (Qubo versions),
fig. 228;
take the tow hook (B) fig. 226
fig. 228 from the tool bag;
fully tighten the ring on the threaded
front or rear pin.
143) 144) 145) 146)
33)
226
F0T0085
227
F0T0420
-------------------------------------------------------------------------------------------------------------------------------------------------------------
IN CASE OF EMERGENCY
170
228
F0T0086
143)
Before towing, turn the ignition key
to MAR-ON and then to STOP without
removing it. The steering column will
automatically lock when the key is
removed and the wheels cannot be
steered.
144)
Before tightening the hook clean
the threaded housing thoroughly. Before
towing the vehicle, make sure that the
tow ring is fully tightened in its appropriate
housing.
145)
Do not start the engine whilst the
vehicle is being towed.
146)
When towing, remember that greater
effort is required on the brake pedal in
order to brake, since the brake servo is
not providing assistance. Do not use
flexible cables when towing and avoid jerky
movements. During towing operations,
make sure that the fastened joint does
not damage adjoining components. When
towing the vehicle, it is necessary to obey
specific road regulations which relate both
to the towing device as well as to the
behaviour to adopt on the road. Do not
start the engine whilst the vehicle is being
towed.
33)
The front and rear tow hooks should
be used only for emergencies on the
road. You are allowed to tow the vehicle
for short distances using an appropriate
device in accordance with the highway
code (a rigid bar), to move the vehicle
on the road in readiness for towing or
transport via a breakdown vehicle. Tow
hooks MUST NOT be used to tow vehicles
off the road or where there are obstacles
and/or for towing operations using cables
or other non-rigid devices. In compliance
with the above conditions, towing must
take place with the two vehicles (one
towing, the other towed) aligned as much
as possible along the same centre line.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст