Suzuki Grand Vitara JB627. Manual — part 4

00-13 Precautions:

Brakes Caution and Note

S6JB0B0000014

CAUTION

!

All brake fasteners are important attaching
parts in that they could affect the
performance of vital parts and systems, and/
or could result in major repair expense. They
must be replaced with one of same part
number or with an equivalent part if
replacement becomes necessary. Do not use
a replacement part of lesser quality or
substitute design. Torque values must be
used as specified during reassembly to
assure proper retention of all parts. There is
to be no welding as it may result in extensive
damage and weakening of the metal.

NOTE
Before inspecting and servicing brakes for
vehicle equipped with ABS, make sure that
ABS is in good condition.

Differential Gear Oil Note

S6JB0B0000015

NOTE

• When having driven through water, check

immediately if water has entered (if so, oil
is cloudy). Water mixed oil must be
changed at once.

• Whenever vehicle is hoisted for any other

service work than oil change, also be sure
to check for oil leakage and status of
breather hoses.

Repair Instructions

Electrical Circuit Inspection Procedure

S6JB0B0006001

While there are various electrical circuit inspection
methods, described here is a general method to check
its open and short circuit by using an ohmmeter and a
voltmeter.

Open Circuit Check
Possible causes for the open circuit are as follows. As
the cause is in the connector or terminal in many cases,
they need to be checked particularly carefully.
• Loose connection of connector
• Poor contact of terminal (due to dirt, corrosion or rust

on it, poor contact tension, entry of foreign object etc.)

• Wire harness being open
When checking system circuits including an electronic
control unit such as ECM, TCM, ABS control module,
etc., it is important to perform careful check, starting with
items which are easier to check.

1) Disconnect negative cable from battery
2) Check each connector at both ends of the circuit

being checked for loose connection. Also check lock
condition of connector if equipped with connector
lock.

3) Using a test male terminal, check both terminals of

the circuit being checked for contact tension of its
female terminal. Check each terminal visually for
poor contact (possibly caused by dirt, corrosion, rust
entry of foreign object, etc.). At the same time, check
to make sure that each terminal is locked in the
connector fully.

4) Using continuity check or voltage check the following

procedure, check the wire harness for open circuit
and poor connection with its terminals. Locate
abnormality, if any.

I2RH01010049-01

1. Check contact tension by inserting and removing just for once.

1. Looseness of crimping
2. Open
3. Thin wire (single strand of wire)

I2RH01010050-01

I2RH01010051-01

Precautions: 00-14

Continuity Check

1) Measure resistance between connector terminals at

both ends of the circuit being checked (between “A-
1” and “C-1” in the figure). If no continuity is indicated
(infinity or over limit), that means that the circuit is
open between terminals “A-1” and “C-1”.

2) Disconnect the connector included in the circuit

(connector-B in the figure) and measure resistance
between terminals “A-1” and “B-1”.
If no continuity is indicated, that means that the
circuit is open between terminals “A-1” and “B-1”. If
continuity is indicated, there is an open circuit
between terminals “B-1” and “C-1” or an abnormality
in connector-B.

Voltage Check
If voltage is supplied to the circuit being checked, voltage
check can be used as circuit check.

1) With all connectors connected and voltage applied to

the circuit being checked, measure voltage between
each terminal and body ground.
a) If measurements were taken as shown in the

figure and results were as listed in the following,
it means that the circuit is open between
terminals “B-1” and “A-1”.

Voltage between each terminal and body
ground
“C-1” and body ground: Approx. 5 V
“B-1” and body ground: Approx. 5 V
“A-1” and body ground: 0 V

b) Also, if measured values were as listed in the

following, it means that there is a resistance
(abnormality) of such level that corresponds to
the voltage drop in the circuit between terminals
“A-1” and “B-1”.

Voltage between
“C-1” and body ground: Approx. 5 V
“B-1” and body ground: Approx. 5 V
“A-1” and body ground: Approx. 3 V
“A-1” and “B-1”: 2V voltage drop

I2RH01010052-01

I2RH01010053-01

I5RH01000005-01

00-15 Precautions:

Short Circuit Check (Wire Harness to Ground)

1) Disconnect negative cable at battery.
2) Disconnect connectors at both ends of the circuit to

be checked.

NOTE
If the circuit to be checked is connected to
other parts (1), disconnect all connectors of
those parts.
Otherwise, diagnosis will be misled.

3) Measure resistance between terminal at one end of

circuit (“A-1” terminal in the figure) and body ground.
If continuity is indicated, it means that there is a short
to ground between terminals “A-1” and “C-1” of the
circuit.

4) Disconnect the connector included in circuit

(connector B) and measure resistance between “A-
1” and body ground.
If continuity is indicated, it means that the circuit is
shorted to the ground between terminals “A-1” and
“B-1”.

Intermittent and Poor Connection Inspection

S6JB0B0006002

Most intermittent are caused by faulty electrical
connections or wiring, although a sticking relay or
solenoid can occasionally be at fault. When checking it
for proper connection, perform careful check of suspect
circuits for:
• Poor mating of connector halves, or terminals not fully

seated in the connector body (backed out).

• Dirt or corrosion on the terminals. The terminals must

be clean and free of any foreign material which could
impede proper terminal contact. However, cleaning
the terminal with a sand paper or the like is prohibited.

• Damaged connector body, exposing the terminals to

moisture and dirt, as well as not maintaining proper
terminal orientation with the component or mating
connector.

1. To other parts

I5RH01000006-01

1. To other parts

I2RH01010056-01

I2RH01010057-01

Precautions: 00-16

• Improperly formed or damaged terminals.

Check each connector terminal in problem circuits
carefully to ensure good contact tension by using the
corresponding mating terminal.
If contact tension is not enough, reform it to increase
contact tension or replace.

• Poor terminal-to-wire connection.

Check each wire harness in problem circuits for poor
connection by shaking it by hand lightly. If any
abnormal condition is found, repair or replace.

• Wire insulation which is rubbed through, causing an

intermittent short as the bare area touches other
wiring or parts of the vehicle.

• Wiring broken inside the insulation. This condition

could cause continuity check to show a good circuit,
but if only 1 or 2 strands of a multi-strand-type wire
are intact, resistance could be far too high.
If any abnormality is found, repair or replace.

1. Check contact tension by inserting and removing just once.
2. Check each terminal for bend and proper alignment.

I5RH01000007-01

I2RH01010059-01

I2RH01010060-01