Suzuki Grand Vitara JB627. Manual — part 237
5A-132 Automatic Transmission/Transaxle:
35) Measure forward clutch pack clearance (A) by
applying compressed air (392 kPa, 4.0 kg/cm
2
, 57
psi) into oil hole, (1) of input shaft as shown in figure.
Pack Clearance
0.4 – 0.7 mm (0.016 – 0.027 in.)
NOTE
Install a selective flange (t 3.4 mm) when
measuring the moving distance. (shaded
area in figure.)
• Flange moving distance A: 0.12 – 1.19 mm
(0.00472 – 0.0468 in.)
Pack Clearance: Flange moving distance A – 0.01
mm (0.00039 in.)
If pack clearance is out of specification, select
another flange with suitable thickness from the list
below and replace it.
Available forward clutch flange thickness
36) Install input shaft assembly (1) to clutch drum
assembly.
37) Install thrust needle roller bearing (1) to clutch drum
assembly.
38) Install thrust bearing race No.2 (1) and input shaft
thrust bearing race (2) to forward clutch hub.
39) Install forward clutch hub (1) to clutch drum
assembly.
Identification
No.
Thickness
Identification
No.
Thickness
0
3.0 mm
(0.118 in.)
6
3.6 mm
(0.142 in.)
1
3.1 mm
(0.122 in.)
7
3.7 mm
(0.146 in.)
2
3.2 mm
(0.126 in.)
8
3.8 mm
(0.150 in.)
3
3.3 mm
(0.130 in.)
9
3.9 mm
(0.154 in.)
4
3.4 mm
(0.134 in.)
A
4.0 mm
(0.158 in.)
5
3.5 mm
(0.138 in.)
—
—
1
A
I4JA01512199-01
1
I4JA01512200-01
1
I4JA01512201-01
2
1
I4JA01512202-01
1
I4JA01512203-01
Automatic Transmission/Transaxle: 5A-133
40) Install 2 thrust needle roller bearings (1) to direct
clutch hub.
41) Install direct clutch hub (1) to clutch drum assembly.
42) Install reverse clutch plates “P” and reverse clutch
discs “D” to reverse clutch hub in the following order.
D - P - D - P - D - P - D - P - D
43) Install reverse clutch flange “F”.
44) Install clutch cushion plate (1) to reverse clutch hub
as shown in figure.
45) Install reverse clutch reaction sleeve (1) to reverse
clutch hub.
46) Install reverse clutch hub sub assembly (1) including
reverse clutch reaction sleeve, clutch cushion plate,
reverse clutch flange, 4 reverse clutch discs and 3
reverse clutch plates to clutch drum assembly.
47) Install snap ring (1) on clutch drum and input shaft
assembly by using flat end rod or the like.
1
I4JA01512204-01
1
I4JA01512205-01
1
P
D
F
I6JB01510042-01
1
I4JA01512207-01
1
I4JA01512208-01
1
I4JA01512209-01
5A-134 Automatic Transmission/Transaxle:
Clutch Drum & Input Shaft Assembly Inspection
S6JB0B5106038
• Check that sliding surface of discs, plate and flange
are not worn or burnt. if necessary, replace them.
NOTE
• If disc lining is exfoliated, discolored or
worn hardly, replace all discs.
• If only a part of printed numbers is
corroded, replace all discs.
• Before assembling new discs, soak them
in A/T fluid for at least 15 minutes.
• Measure inside diameter of reverse clutch hub
bushing. If inside diameter exceeds limit, replace
reverse clutch hub.
Reveres clutch hub bushing inside diameter
Standard: 35.812 – 35.837 mm (1.4099 – 1.4109 in.)
Limit: 35.887 mm (1.4129 in.)
• Measure inside diameter of direct clutch hub bushing.
If inside diameter exceeds limit, replace direct clutch
hub.
Direct clutch hub bushing inside diameter
Standard: 26.037 – 26.062 mm (1.0251 – 1.0261 in.)
Limit: 26.112 mm (1.028 in.)
• Measure free length of forward clutch return spring
including spring seat.
Forward clutch return spring free length
“a”: 26.74 mm (1.053 in.)
NOTE
• Do not apply excessive force when
measuring spring free length.
• Perform measurement at several points.
I4JA01512210-01
I4JA01512211-01
I4JA01512212-01
“a”
I4JA01512213-01
Automatic Transmission/Transaxle: 5A-135
• Measure free length reverse clutch return spring
including spring seat.
Reverse clutch return spring free length
“a”: 21.04 mm (0.828 in.)
NOTE
• Do not apply excessive force when
measuring spring free length.
• Perform measurement at several points.
• Measure free length direct clutch return spring
including spring seat.
Direct clutch return spring free length
“a”: 19.51 mm (0.768 in.)
NOTE
• Do not apply excessive force when
measuring spring free length.
• Perform measurement at several points.
“a”
I4JA01512214-01
“a”
I4JA01512215-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст