Toyota Tundra. Manual — part 2484
Fig. 44: Identifying Rear Combination Light Connector Terminals - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Measure the resistance according to the value(s) in the table below.
Standard resistance
REAR COMBINATION LIGHT - TURN SIGNAL FLASHER AND BODY GROUND
RH
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
6. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - TURN SIGNAL
FLASHER AND BODY GROUND)
a. for LH:
1. Disconnect the N5 light connector.
2. Disconnect the J29 relay connector.
Tester Connection
Condition Specified Condition
R4-5 (TRN) - J29-8 (LR)
Always
Below 1 ohms
R4-6 (E) - Body ground
R4-5 (TRN) - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Fig. 45: Identifying Outer Rear View Mirror Connector Terminals - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Measure the resistance according to the value(s) in the table below.
Standard resistance
OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER AND BODY GROUND
LH
b. for RH:
1. Disconnect the M6 light connector.
2. Disconnect the J29 relay connector.
Tester Connection
Condition Specified Condition
N5-4 (B) - J29-2 (LL)
Always
Below 1 ohms
N5-3 (E) - Body ground
NS-4 (B) - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Fig. 46: Identifying Outer Rear View Mirror Connector Terminals - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Measure the resistance according to the value(s) in the table below.
Standard resistance
OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER AND BODY GROUND
RH
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
HAZARD WARNING SWITCH CIRCUIT
DESCRIPTION
The turn signal flasher receives a hazard warning signal switch information signal, and illuminates the turn
signal lights.
Tester Connection
Condition Specified Condition
M6-4 (B) - J29-8 (LR)
Always
Below 1 ohms
M6-3 (E) - Body ground
M6-4 (B) - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
WIRING DIAGRAM
Fig. 47: Hazard Warning Signal Switch - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. INSPECT HAZARD WARNING SIGNAL SWITCH
a. Remove the hazard warning signal switch (see REMOVAL ).
Fig. 48: Identifying Hazard Warning Signal Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
HAZARD WARNING SIGNAL SWITCH
Tester Connection
Switch Condition
Specified Condition
Hazard warning switch ON
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст