Toyota Tundra. Manual — part 721
DESCRIPTION
HINT:
for Double Cab, CrewMax
If the rear LH side manual UP/DOWN function does not operate, there may be a malfunction in the rear power
window regulator switch LH, rear power window regulator motor LH, power window regulator master switch
or harness and connector.
WIRING DIAGRAM
Fig. 22: Rear Power Window Regulator Motor Assembly LH Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - BATTERY)
a. Disconnect the O11 switch connector.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
STANDARD VOLTAGE TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Switch Condition Specified Condition
O11-3 (B) - Body ground Ignition switch ON
11 to 14 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 23: Identifying Front View Of Wire Harness Connector Terminals (To Rear Switch LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a. Remove the switch (see REMOVAL ).
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
STANDARD RESISTANCE TESTER CONNECTION SPECIFIED CONDITION
Tester Connection Switch Condition Specified Condition
4 (U) - 3 (B)
UP
Below 1 ohms
1 (D) - 2 (SD)
4 (U) - 5 (SU)
OFF
Below 1 ohms
1 (D) - 2 (SD)
4 (U) - 5 (SU)
DOWN
Below 1 ohms
1 (D) - 3(B)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 24: Identifying Component Without Harness Connected Terminals (Rear Switch LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (see
REMOVAL )
OK: Go to Next Step
3. CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - REAR MOTOR LH)
Fig. 25: Identifying Front View Of Wire Harness Connector Terminals (To Rear Switch LH And
Rear Motor LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Disconnect the O11 switch connector.
b. Disconnect the O9 motor connector.
c. Measure the resistance according to the value(s) in the table below.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Standard resistance
for Double Cab:
REAR SWITCH LH - REAR MOTOR LH (FOR DOUBLE CAB)
for CrewMax:
REAR SWITCH LH - REAR MOTOR LH (FOR CREWMAX)
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
4. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a. Remove the motor (see REMOVAL ).
b. Apply battery voltage to connector terminals 1 and 2.
c. Check that the motor gear rotates smoothly as follows.
OK
MOTOR GEAR MEASUREMENT SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
O11-1 (D) - O9-2
Always
Below 1 ohms
O11-4 (U) - O9-1
O11-1 (D) or O9-2 - Body ground
Always
10 kohms or higher
O11-4 (U) or O9-1 - Body ground
Tester Connection
Condition Specified Condition
O11-1 (D) - O9 - 1
Always
Below 1 ohms
O11-4 (U) - O9 - 2
O11-1 (D) or O9-1 -Body ground
Always
10 kohms or higher
O11-4 (U) or O9-2-Body ground
Measurement Condition
Specified Condition
Battery positive (+) --> 1
Battery negative (-) --> 2
Motor gear rotates clockwise
Battery positive (+) --> 2
Battery negative (-) --> 1
Motor gear rotates counterclockwise
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст