Toyota Tundra. Manual — part 836

2. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH

a. Remove the screw.

b. Detach the claw and remove the license plate light.

3. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

4. REMOVE REAR BUMPER COVER

a. w/ Intuitive Parking Assist System:

Disconnect the connectors and clamps shown in illustration.

Fig. 80: Identifying Rear Bumper Cover Claws And Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Fig. 81: Locating Rear Bumper Cover Connectors And Clamps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

b. Remove the 2 clips and 4 screws.



After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra

c. Remove the 4 bolts and 2 nuts.

d. Detach the 4 claws and remove the rear bumper cover.

Fig. 82: Identifying Rear Bumper Cover Clips And Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

5. REMOVE REAR BUMPER PAD SUB-ASSEMBLY

a. Remove the 6 bolts and bumper pad.

Fig. 83: Identifying Bumper Pad Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

6. REMOVE REAR NO. 1 BUMPER SUPPORT

a. Remove the bumper support.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra

Fig. 84: Identifying Bumper Support
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

7. REMOVE REAR BUMPER SIDE EXTENSION SUB-ASSEMBLY LH

a. Remove the 3 screws, bolt and side extension.

Fig. 85: Identifying Rear Bumper Side Extension Screws And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

8. REMOVE REAR BUMPER SIDE EXTENSION SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.

9. REMOVE NO. 3 WIRE FRAME (w/ Trailer Towing System)

a. Disconnect the connector.

b. Detach the clamp.

c. Remove the 2 bolts and wire frame.

Fig. 86: Identifying Bolts And Wire Frame
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

DISASSEMBLY

1. REMOVE REAR BUMPER SIDE RETAINER LH

a. Remove the 4 clips and retainer.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra

Fig. 87: Identifying Clips And Retainer
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

2. REMOVE REAR BUMPER SIDE RETAINER RH

HINT:

Use the same procedures described for the LH side.

3. REMOVE NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System) (See REMOVAL )

4. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System) (See

REMOVAL )

5. REMOVE NO. 2 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System) (See REMOVAL )

6. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System) (See

REMOVAL )

REASSEMBLY

1. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System) (See

INSTALLATION )

2. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System) (See

INSTALLATION )

3. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System) (See

INSTALLATION )

4. INSTALL NO. 2 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System) (See

INSTALLATION )

5. INSTALL REAR BUMPER SIDE RETAINER LH

a. Install the retainer with the 4 clips.

2009 Toyota Tundra

2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra