Toyota Tundra. Manual — part 2015
Fig. 195: Locating Air Injection Control Driver Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
m
Remove the nut and disconnect the wire and 2 clips from the engine room junction block
n
Disconnect the 2 connectors and 2 clips from the engine room junction block
22
DISCONNECT COOLER COMPRESSOR ASSEMBLY (See REMOVAL )
23
DISCONNECT VANE PUMP ASSEMBLY (See REMOVAL )
24
REMOVE GENERATOR ASSEMBLY (See REMOVAL )
25
REMOVE EXHAUST PIPE ASSEMBLY
a
for Regular Cab Standard Deck:
Refer to the following procedures (see REMOVAL )
b
except Regular Cab Standard Deck:
Refer to the following procedures (see REMOVAL )
26
REMOVE PROPELLER SHAFT ASSEMBLY
a
for 2WD:
Refer to the following procedures (see REMOVAL )
b
for 4WD:
Refer to the following procedures (see REMOVAL )
27
REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
a
Remove the front propeller shaft (see REMOVAL )
28
REMOVE FRONT FENDER APRON SEAL RH (See REMOVAL )
29
REMOVE FRONT FENDER APRON SEAL REAR RH (See REMOVAL )
30
REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE (See REMOVAL )
31
REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (See REMOVAL )
32
REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (See REMOVAL )
33
REMOVE STARTER COVER (See DISASSEMBLY )
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
34
REMOVE STARTER ASSEMBLY (See DISASSEMBLY )
35
REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
a
for 2WD:
Refer to the following procedures (see REMOVAL )
b
for 4WD:
Refer to the following procedures (see REMOVAL )
36
REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
a
Using SST, hold the crankshaft
SST 09213-70011,09330-00021
Fig. 196: Holding Crankshaft
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor
Fig. 197: Locating Rear Drive Plate Spacer, Drive Plate And Crankshaft Angle Sensor Rotor
Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
37
REMOVE NO. 1 WATER BY-PASS PIPE
a
Remove the 2 bolts and disconnect the hose Then remove the water by-pass pipe
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 198: Locating No. 1 Water By-Pass Pipe Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
38
REMOVE ENGINE ASSEMBLY
a
Install the 2 engine hangers with the 2 bolts as shown in the illustration
Engine hanger part No.
ENGINE HANGER PART NUMBER REFERENCE CHART
Fig. 199: Locating Engine Hangers
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Torque: 43 N*m (438 kgf*cm, 32 ft.*lbf)
b
Attach an engine sling device and hang the engine with a chain block
c
Remove the 4 engine mounting insulator bolts
Item
Part No.
Engine hanger 12281-38030,12281-38060
Bolt
90119-14120, 90119-A0166
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 200: Locating Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Lift the engine out from the vehicle slowly and carefully
39
REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (See REMOVAL )
40
REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH (See REMOVAL )
41
INSTALL ENGINE ON ENGINE STAND
a
Install the engine onto an engine stand with the bolts
b
Remove the 2 bolts and 2 engine hangers
INSTALLATION
1
REMOVE ENGINE STAND
a
Install the 2 engine hangers with the 2 bolts as shown in the illustration
Engine hanger part No.
ENGINE HANGER PART NUMBER REFERENCE CHART
NOTE:
Make sure the engine is clear of all wiring, hoses and cables.
Item
Part No.
Engine hanger 12281-38030,12281-38060
Bolt
90119-14120, 90119-A0166
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст