Ford Falcon. Manual — part 157
303-01c-49
Engine — V8 (4V)
303-01c-49
REMOVAL (Continued)
10. Remove the radiator.
24. Disconnect fuel lines using special tool, as
outlined in Section 310-00.
1. Remove the bolts.
25. Disconnect the power steering pressure (PSP)
2. Remove the upper radiator support brackets.
sensor.
3. Remove bolts attaching condensor to radiator.
26. Remove the bolts and position the power steering
4. Lift the radiator off the radiator mounting
pump out of the way.
insulators.
5. Remove the radiator mounting insulators.
11. Remove the accessory drive belt. For additional
information, refer to Section 303-05.
12. Disconnect the alternator electrical connectors.
13. Disconnect battery and alternator cables from RH
Relay box.
14. Remove PCM, refer to Section 303-14-104.
15. Disconnect the wiring harness (PCM ‘A’ connector
& 24 pin connector) from vehicle.
16. Disconnect transmission wiring harness from
transmission.
17. Disconnect hego sensor wiring plugs. Refer to
chapter Section 303-14-106 for more information.
18. Remove the ground strap retaining bolt.
27. Disconnect the starter motor electrical
connections.
1. Remove the two nuts.
2. Remove the battery cable.
3. Remove the starter solenoid wire.
19. Disconnect the lower radiator hose.
20. Disconnect the heater hoses from rear of engine.
21. Disconnect brake booster vacuum hose.
22. Disconnect purge valve connection.
23. Disconnect air intake to throttle body and remove
entire air cleaner assembly.
G89795 en
303-01c-50
Engine — V8 (4V)
303-01c-50
REMOVAL (Continued)
28. Remove the nut and the starter motor ground
31. Disconnect the A/C compressor electrical
cable.
connector.
29. Remove the three bolts and the starter motor.
32. Remove the bolts and the A/C compressor.
NOTE: Do not degas, position A/C compressor
out of the way.
30. Disconnect the crankshaft position (CKP) sensor.
33. Remove nut holding exhaust heatshield and
discard, then remove heatshield.
34. Disconnect the pipes at the exhaust manifolds.
NOTE: If studs are removed from exhaust
manifolds during disassembly, then discard studs
and nut and replace with new parts.
35. Remove the through bolt from the LH engine
mount.
G89795 en
303-01c-51
Engine — V8 (4V)
303-01c-51
REMOVAL (Continued)
36. Remove the through bolt from the RH motor
39. Remove the five bolts from the transmission.
mount.
40. Lower the vehicle.
37. Remove the plate bolts and the inspection cover.
41. Install rear lifting hook and front lifting hook.
42. Support the transmission with a floor jack and a
block of wood.
43. Remove the engine from the vehicle.
38. Remove the four nuts from the torque converter
and discard (Auto tran only).
NOTE: Gain access to the nuts by turning the
crank dampener counterclockwise.
G89795 en
303-01c-52
Engine — V8 (4V)
303-01c-52
DISASSEMBLY
Special Tool(s)
Engine
Compressor, Valve Spring
(Exhaust Side)
Special Tool(s)
303-567 (T97P-6565-AH)
Remover, Crankshaft Rear Oil
Seal
303-519 (T95P-6701-EH)
Compressor, Valve Spring
(Intake Side)
303-452 (T93P-6565-AR)
Remover, Crankshaft Rear Oil
Slinger
303-514 (T95P-6701-AH)
Cylinder Ridge Reamer
303-016 (T64L-6011-EA)
Impact Slide Hammer
100-001 (T50T-100-A)
Disassembly
NOTE: The crankshaft rear oil seal slinger and the oil
Lift Bracket Set, Engine
seal retainer plate must be removed before mounting
303-DS086 (D93P-6001-A)
the engine on the engine stand.
1. Remove the bolts and the flywheel ring gear.
Remover, Crankshaft Vibration
Damper
303-009 (T58P-6316-D)
Installer, Connecting Rod
303-442 (T93P-6136-A)
Remover, Crankshaft Front Oil
Seal
303-107 (T74P-6700-A)
G89796 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст