Ford Falcon. Manual — part 411
501-05-13
Interior Trim and Ornamentation
501-05-13
REMOVAL AND INSTALLATION (Continued)
Front Inner Scuff Plate (LH)
Rear Outer Scuff Plate
Removal
Removal
1. Remove front inner scuff plate (LH) as shown in
1. Remove outer scuff plate as shown in figure.
figure .
Item
Description
Installation
1
Screw
1. Reverse removal procedure.
2
Front Outer Scuff Plate
Rear Inner Scuff Plate
3
Screw Grommet
4
Rear Outer Scuff Plate
Removal
1. Remove rear inner scuff plate as shown in figure.
Installation
1. Reverse removal procedure.
Installation
1. Reverse removal procedure.
G11876 en
501-08-1
Exterior Trim and Ornamentation
501-08-1
SECTION : 501-08 Exterior Trim and
Ornamentation
VEHICLE APPLICATION : 2003.0 BA Falcon
CONTENTS
PAGE
DESCRIPTION AND OPERATION
Exterior Trim and Ornamentation . . . . . . . . . . . . . . . . . . . . . . .501-08-2
REMOVAL AND INSTALLATION
Radiator Grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...501-08-3
Licence Plate Housing . . . . . . . . . . . . . . . . . . . . . . . . . . ..501-08-3
Rear Decklid Moulding — High Series, SWB Sedan . . . . . . . . . . . . . . . 501-08-4
Rear Decklid Moulding — Low Series, SWB Sedan . . . . . . . . . . . . . . . 501-08-4
Rear Liftgate Moulding — Wagon . . . . . . . . . . . . . . . . . . . . . . .501-08-5
Rear Decklid Moulding — Wagon . . . . . . . . . . . . . . . . . . . . . . .501-08-5
Window Moulding . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..501-08-5
Door Moulding — All Vehicles . . . . . . . . . . . . . . . . . . . . . . . ..501-08-6
Rocker Panel Moulding — SWB & LWB . . . . . . . . . . . . . . . . . . . ..501-08-7
Body Side Protection Moulding . . . . . . . . . . . . . . . . . . . . . . . .501-08-7
Roof Ditch Moulding . . . . . . . . . . . . . . . . . . . . . . . . . . . ..501-08-8
Decklid Spoiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..501-08-8
501-08-2
Exterior Trim and Ornamentation
501-08-2
DESCRIPTION AND OPERATION
Exterior Trim and Ornamentation
Component Location
Item
Description
1
Radiator Grille
2
Hood Moulding
3
Door Moulding
4
Window Moulding
5
Roof Ditch Moulding
6
Decklid Spoiler
7
Licence Plate Moulding
8
Rocker Pane Moulding
9
Door Moulding
G86721 en
501-08-3
Exterior Trim and Ornamentation
501-08-3
REMOVAL AND INSTALLATION
Radiator Grille
Licence Plate Housing
Removal
Removal
1. Raise the Hood.
1. Gently use a screwdriver to depress the clip tab
on the side of the lamp housing to remove it from
2. Remove the two scrivets along the top rear edge
the applique.
of the grille.
NOTE: The lamp will still be attached to the
3. Lift the grille up and away.
applique by the bulb holder and wiring.
Hi Series
Item
Description
1
Scrivet - 8mm
Item
Description
2
Grille - SWB/UTE
1
Number Plate Lamp
Lo Series
Item
Description
1
Scrivet - 8mm
Item
Description
2
Grille - LWB
1
Number Plate Lamp
Installation
2. Turn the bulb holder approximately 1/8 of a turn
1. To install, reverse the removal procedure.
anti-clockwise until it is free of the lamp housing.
Installation
1. To install, reverse the removal procedure.
NOTE: Tabs prevent the bulb holder from being
inserted into the lamp housing at the incorrect
orientation. Do not apply force.
G86722 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст