Chery B14. Manual — part 30
II. Disassembly of Instrument Panel
1 Disassembly/assembly of instrument panel
1.1 Disassembly steps
1.1.1 Disassemble steering wheel and combined switch
(Refer to disassembly of steering wheel)
1.1.2 Disassemble glove box
(Refer to disassembly of glove box)
1.1.3,Disassemble audio, AC control panel
(Refer to disassembly of audio and AC control panel)
1.1.4 Disassemble front ash tray
(Refer to disassembly of front ash tray)
1.1.5 Disassemble combined instrument
(Refer to disassembly of combined instrument )
1.1.6 Disassemble armrest box and vice instrument panel
(Refer to disassembly of armrest box and vice instrument
panel)
1.1.7 Disassemble A pillar upper and lower trim plate.
1.1.8 Disassemble left front and right front door opening
weather strip
1.1.8 Prize sun light sensor out carefully by flat head
screwdriver.
1.1.9 Unplug the plug behind of sun light sensor.
1.1.10 Disassemble 7 fixing screws which fix upper instrument panel and lower instrument
panel body, take off up instrument panel assembly left and right ventilator. Installation torque is
1.5±0.5Nm
1.1.11 Unscrew 6 fixing screws and 2 fixing bolts of low ventilator assembly, take off instrument
panel AC ventilator assembly.
Tool: cross head screwdriver, No.8 socket spanner. Installation torque is 1.5±0.5 Nm
1.1.12 Unscrew two fixing bolts below lower instrument
panel at the driver side by No. 8 socket spanner.
Installation torque is 7±1 Nm
No. 8 bolt
screw
1.1.13 Unscrew two fixing bolts above lower instrument panel
at the driver side by No. 8 socket spanner.
Installation torque is 7±1 Nm.
1.1.13 Unscrew 2 fixing screws on the middle of lower
instrument panel. Installation torque is 7±1 Nm
1.1.14 Unscrew two fixing bolts below lower instrument panel
at the codriver side by No. 8 socket spanner.
Installation torque is 7±1 Nm.
1.1.15 Unscrew 3 fixing bolts above lower instrument panel at
the driver side by No. 8 socket spanner.
Installation torque is 7±1 Nm.
1.1.16 Take off lower instrument panel body.
1.2 Assembly steps of instrument panel
The installing steps are reverse to those for removal.
Note:
1.2.1 The ventilator of instrument should be coincide with AC
air outlet, there should be no incorrect assembly, no air leaking,
no interference between instrument panel air passage and
instrument cross beam, and evaporator, which will influence the
instrument panel assembly.
1.2.2 There should be no interference between windscreen and
instrument panel, the clearance to windscreen should be even.
1.2.3 Clearance between instrument panel and body sides
should be even and can meet door weather strip assembly
requirements
1.2.4 Glove box should be flexible for opening and closing, no
interference, no block or lock loose.
1.2.5 Assemble the middle passage cover plate tightly, clearance
between sub instrument panel body, armrest box should be even
and less than 0.5mm.
1.2.6 Fasten torque of sub instrument panel front, middle end
and rear end of armrest box, middle passage cover plate middle
and rear end fixing bolt is 2±0.5N.
1.2.7 Fasten torque for vent of instrument panel and upper and
lower body fixing screw is 5±0.5N。
2 Disassembly of instrument cross beam
2.1 Disassembly steps
2.1.1 Disassemble instrument panel assembly (Refer to
disassembly of instrument panel)
2.1.2 Disassemble the plugs between instrument panel cross
beam cable and every elements, disassemble instrument cable
(Refer to disassembly/assembly of instrument cable)
2.1.3 Disassemble 2 instrument panel fuse box fixing screws
by cross head screwdriver, take off fuse box.
Installation torque is 1.5±0.5 Nm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст