Chery B14. Manual — part 24
5.3 Loose two fog lamp fixing nuts by No. 7 sleeve.
5.4 Take out fog light assembly.
6 Installation and adjustment of
headlamp
6.1 Assembly steps of headlamp
The installing steps of headlamp are reverse
to those for removal.
6.2,Introduction of headlamp function
6.2.1,Front view
See right figure:
1
Low beam light
2
Position light
3
High beam
4
Turn light
6.2.2 Back view
See right figure:
1
Low beam light holder
2
Plug for low, high and position
light
3
Position light holder
4
High beam light holder
5
Turn light holder and plug
6
Low beam up/down adjusting nut
7
Low beam left/right adjusting nut
8
High beam up/down adjusting nut
9
High beam left/right adjusting nut
1
2
3
4
1
2
3
4
5
6
7
8
9
6.3 Adjustment for headlamp beam
6.3.1 Headlamp uses half closed light combination type. So it is easy to be maintained; it is
halogen light with less mechanism and high luminous intensity, which will prolong bulb life.
6.3.2 The correctness of headlamp adjustment will influence the driving safety. So it needs
special device to adjust the beam. Pay attention to law regulations and verify the following items
before adjustment:
a.
Tire pressure should be correct;
b.
Car is unload (except for spare tire and equipped tools, and include driver weigh for
sedan);
c.
Park the car on horizontal road or place;
d.
The lens surface of headlamp should be clean;
e.
Check the power supplies if is working correctly, and the bulb installed correctly.
Move the adjustable mechanism on the light can adjust the beam up/down and left/right, operate it
with international standard. Adjuster for rough and fine up/down adjustment is one unit on casing
upside; adjuster for left/right on casing middle and lower side.
It needs take off headlamp cover to adjust right headlamp. Same to the symmetrical lay of left
headlamp adjustment mechanism and right headlamp.
6.3.3 Headlamp beam adjustment can be realized by moving beam adjusting nut or power
adjusting button (if it is equipped).
6.3.3.1 Insert cross head screwdriver to related
adjusting holes to adjust the beam.
6.3.3.2 Adjust the beam up and down by power adjusting
button on the instrument panel.
6.3.3.3 The norm central height for Chery V325 headlamp:
Low beam:717mm;High beam:755mm。
6.3.3.4 Adjust the headlamp beam according to international
standards:
During check headlamp low beam lighting position, irradiate the headlamp to the screen 10m far
away from headlamp, for low beam of passenger car, angle of cut-off line or height of midpoint
height should be 0.7H~0.9H (H is the midpoint height of headlamp, the same of below), other
motor vehicles(except for tractor) should be 0.6H~0.8H. Deviation to left of horizontal direction
position headlamp low beam of motor vehicle (except for the vehicle with one front headlamp)is
not allowed to exceed 170mm,not exceed 350 mm to right.(From national standard)
6.3.3.5 Please input the standard data got from above into headlamp beam adjusting device for
future usage.
Chapter Six Disassembly/Assembly of Roof and Scuttle
I. Disassembly/Assembly of Roof
1 Preparation
Tool: No. 7, No. 8, No. 13 and No. 17 socket spanner, cross
head screwdriver and flat head screwdriver.
2 Note
2.1 Use correct force during operation to prevent damage
the parts and it is not allowed to operate with too big force.
2.2 Protect the part surface from scratching during the
disassembly/assembly of inner trim.
3 Disassembly/assembly of sunvisor
3.1 Disassembly steps
3.1.1 Loose left front sunvisor two fixing screws by
cross head screwdriver and the torque is 3±1Nm
3.1.2 Pull out left front sunvisor cable plug.
3.1.3 Take away left front sunvisor.
3.2 Assembly steps
The installing steps are reverse to those for removal.
3.3 Disassembly/assembly of right front sun visor, please
refer to that of left front sunvisor.
4 Disassembly/assembly of ceiling handle
4.1 Disassembly steps
4.1.1 Prize handle fixing screw cover by flat head
screwdriver.
4.1.2 Disassemble fixing screw by cross head screwdriver.
Torque is 9±3Nm
4.1.3,Take off the handle.
4.2 Assembly steps
The installing steps are reverse to those for removal.
4.3 Disassemble/assemble other handles refer to right front
handle.
5 Disassembly/assembly of front ceiling light
5.1 Disassembly steps
5.1.1 Prize front ceiling light cover by flat head
screwdriver.
Note: do not scratch part surface.
5.1.2 Loose front ceiling light fixing bolt.
Torque is 1.5±0.5Nm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст