Chery B11. Manual — part 150
Chery Eastar Service Manual Body Dimension and Accessories
51
Clean the detached windshield
l. Apply a scraper to remove the adhesive on the
windshield.
2. Apply the cleaning solution to rinse the windshield.
WARNING: Do not touch the windshield after cleaning.
Replace the clamping piece if necessary.
l. Apply a knife to detach the stopper.
2. Remove the old clamping piece.
3. Replace it with a new clamping piece.
Windshield Positioning
l. Place the windshield in a proper position.
2. Note the reference markings on the windshield and
body.
3. Remove the windshield.
Clean the contact surface of windshield
Apply the cleaning solution to remove the black smudges
on the contact surface around the windshield.
WARNING: Do not touch the surface of windshield after
cleaning.
PDF created with pdfFactory Pro trial version
Chery Eastar Service Manual Body Dimension and Accessories
52
Install the Draining Plate
Apply the doubleside tape to install the draining plate, as
shown in the right picture.
WARNING: Do not touch the surface of windshield after
cleaning.
Apply a coat of primer M on the contact surface of
body:
Use a brush to coat primer M on the contact
surface of body.
WARNING: The primer coating shall be dried for more
than 3 minutes, do not apply the primer on the adhesive,
and do not store the unsealed primer M till to the future
application.
Apply a coat of primer G on the contact surface
of windshield
l. Use a brush or sponge to apply a coat of primer G on
the edge and contact surface of windshield.
2. Apply a clean cloth to wipe off the primer before it
dries.
WARNING: The primer coating shall be dried more than
3 minutes, do not apply the primer on the adhesive, and
do not store the unsealed primer G for any future
application.
Mix the Adhesive
WARNING: It shall be ensured that the assembly of panel
strip is finished during the adhesive available period and
the adhesive is mixed successfully within 5 minutes.
l. Apply the dissolvent to thoroughly clean the glass
plate and putty scraper.
2. On the glass plate or equivalents, apply a scraper to
fully mix the 500 g main agent and the 75 g hardening
agent.
7 mm (0.28 in)
Primer M
Primer M
Primer M
Primer G
Adhesive
PDF created with pdfFactory Pro trial version
Chery Eastar Service Manual Body Dimension and Accessories
53
Apply the Adhesive
l. Cut off the nozzle of tube-shaped kettle and add the
adhesive into the kettle.
2. Fill the tube-shaped kettle into the sealant gun.
3. Apply the adhesive on the windshield, as shown in the
right picture.
Install the Windshield
Hint: Make sure that the draining plate has been adhered
to the panel of body, as shown in the right picture.
l. Install the windshield to align the windshield with the
reference making on the body, and then pressure the
windshield gently into the frame along its edge.
2. Use a scraper to apply the adhesive on the edge of
windshield.
3. Use the scraper to remove the excessive or
overflowing adhesive.
4. Clamp the windshield tightly till the adhesive gets
hardened.
Check the leakage of water, and repair it.
l. Conduct the water leakage test after the adhesive gets
hardened.
2. Apply the sealant to seal the part of water leakage.
Part Number: 08833-00030 or equivalents
10 mm (0.39 in)
Adhesive
2.7 mm (0.11 in)
PDF created with pdfFactory Pro trial version
Chery Eastar Service Manual Body Dimension and Accessories
54
Rear Windshield Panel Strip and Glass Parts
Lower panel strip
High mount brake lamp
Rear door frame plate
Storage box trim plate
Rear Seat Backrest
Rear seat cushion
Speaker mesh
Joint
Cap
Upper panel strip
Rear windshield
Roof lining
Rear seat side trim
Rear door frame
plate
Roof side trim
Rear seat side trim
PDF created with pdfFactory Pro trial version
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст