Chery Tiggo T11 LHD. Manual — part 10
Chery T11 Service Manual
Body and Accessories
-38-
6) Clean the contact of the glass.
Clean any dirt on the perimetric surface with
detergent.
Note: Please do not touch the surface of
glass after cleaning.
7) Install waterstop.
Install the waterstop by double sided
adhesive tape as shown in the figure.
Note: Please do not touch the surface of
glass after cleaning.
8) Paint a layer of primer M at the contact
with body.
Paint a layer of primer M at the surface of
body with brush.
Note:
Please wait for more than 3 minutes to allow
the primer drying up.
Please do not paint on the adhesive.
Please do not keep unsealed primer M for
future use.
9) Paint a layer of primer G at the contact
with glass.
a. Paint a layer of primer G at the glass
edge or contact with brush or sponge.
b. Wipe it out with clean cloth before the
primer is drying up.
Note:
Please wait for at least 3 minutes to allow the
primer drying up.
Please do not paint on the adhesive.
Please do not keep unsealed primer G for
future use.
Primer M
Adhesive
7mm (0.28in)
Primer M
Primer M
Primer G
Chery T11 Service Manual
Body and Accessories
-39-
10) Adhesive Mixing.
a. Clean the glass and scraper with
solvent.
b. Mix 500g of main solvent with 75g of
hardener by scraper on glass or similar
stuff.
Note:
Make sure to complete the installation of fillet
within the valid period of adhesive.
The adhesive shall be mixed within 5 minutes.
11) Adhesive Applying
a. Cut off the tip of the tube, and fill the
adhesive into the tube.
b. Install the tube into sealed glue gun.
c. Apply the adhesive to the glass as
shown in the figure.
12) Glass Installation.
Hint: Make sure that the waterstop is well
sticked to the body as shown in the figure.
a. Install the glass, and have the marks on
the glass well aligned with the marks on
the body, then press the edge to push the
glass into its place gently.
b. Apply some adhesive on the edge of the
glass with scraper.
10mm (0.39in)
Adhesive
Chery T11 Service Manual
Body and Accessories
-40-
c. Remove excessive or overflow adhesive
by scraper.
d. Clamp the glass till the adhesive is
hardened.
13) Check for any leakage, and have it
repaired.
a. Carry out leakage test after the period
for hardening.
b. Block any leakage with glue.
14) Install the top fillet for windscreen.
Install the top fillet onto the body, bat it
gently with hand to have it well installed.
15) Install the fillet outside.
Install the fillet outside as well as the bolt.
2. Replacement of Rear Windscreen
Dismantle Procedure
1) Remove the lower fillet
2) Cut off the adhesive at both sides of both
ends of the fillet by scraper as shown in the
figure.
Hint: The tip of the scraper shall be wrapped
with tape before use.
Prize up the fillet at six nips by scraper, and
remove the fillet.
3) Remove the glass of rear window.
Lead a wire string toward outside between
the body and the glass.
Bind both ends of the string with wooden
block or similar stuff.
Hint: Please do not damage the two blocks
by the wire string.
Remove the glass
4) Remove the fillet of rear window.
2.7mm (0.11in)
Chery T11 Service Manual
Body and Accessories
-41-
Installation Procedure
1) Install the fillet for rear window
Place the fillet around the glass by hand.
Hint: The rear window glass must be
removed for the installation of the fillet.
2) Clean and trim the contact with body
Cut off any coarse on the body.
Hint: Leave as much as adhesive on the
body.
Clean the cutting surface of adhesive with
clean cloth soaked with detergent.
Hint: The vehicle surface shall be cleaned
even all adhesives are removed.
3) Remove the block.
Remove the block by knief.
4) Clean the dismantled windscreen.
a. Remove any adhesive on the glass by
scraper
b. Clean the glass with detergent
Note: Please do not touch the glass after
cleaning.
Adhesive
Block
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст