Chery Tiggo T11 LHD. Manual — part 44

T11 Service Manual Suspension and Steering

Ⅺ Removal and Installation of Rear Stabilizer Bar

Disassembly procedures:

1) Remove the intermediate pipe assembly (Refer to the removal and installation section of

intermediate pipe assembly).

2) Remove the intermediate propeller shaft assembly (Refer to the removal and installation section

of intermediate propeller shaft).

3) Remove the fuel tank assembly (Refer to the removal and installation section of fuel tank

assembly).

4) Unscrew the bolt that joins rear stabilizer bar and rear connecting rod (Refer to the removal and

installation section of rear connecting rod).

5) Unscrew the bolt joining the rear brake line and

the bracket, and then remove the rear brake line (one

at each side).

6) Unscrew the bolt joining rear stabilizer bar to

vehicle body. (One at each side).

Installation procedures:

1) Refer to disassembly procedures to perform assembly.

2) Precautions:

a) Once loosening the binding bolt whose torque and angle tightening condition is controlled by

yield limit, it must be replaced.

b) After installation, torque each bolt to specification.

T11 Service Manual Suspension and Steering

Steering System

General Description

T11 employs hydraulic power steering system, which consists of steering pump, steering engine,

steering line, steering liquid reservoir, etc.

The steering gear is a kind of rack-and-gear power type. It employs rotary plug valve structure and

outputs at two terminals. There is a dust cover at the joint of steering link and rack. The piston rod

and rack are integrated into a single unit. The length of steering link can be adjusted to fit the

toe-in. Steering gear link exterior ball is tightened to the knuckle by self-locking nut, so it is

unnecessary to employ lock pin.

Steering pump is a kind of permanent flow vane type, and the maximum working pressure is

8±0.5Mpa. When the speed is between 1250rpm and 3000 rpm, the flow tends downward. When

exceeding 3000rpm, the flow is not markedly increased. So it can guarantee satisfied "road felt"

when running at high speed. It also improves driving safety when vehicle running at high speed.

So please make every effort to avoid steering to the limit position for over 10 seconds when the

vehicle is in service.

Steering oil pipe is used to supply steering oil. According to different distances and working

characteristics among varied assembly components, the steering oil pipe of T11 is a kind of hybrid

type combining steel pipe and hose. The connection between steel pipe and hose of high-pressure

oil pipe assembly is a kind of cutting sleeve junction, so it has reliable sealing performance. The

connection of oil pipe and steering gear employs bolt and O-ring, which also ensures reliable

sealing.

The main functions of steering liquid reservoir include: store oil and supply oil to oil pump and

system; radiate heat and reduce the oil working temperature; filter impurities and ensure the

cleanliness of working oil and fluid. Oil type shall be Shell Donax ATF, and the implementation
standard of automatic gearbox oil shall be Dexron Ⅲ.

T11 Service Manual Suspension and Steering

Layout

Fastener Tightening Specification

Application

Specification

Tightening torque

Steering wheel fixing nut

M12×1.2 5

27~33N.m

Steering column upper bracket fixing bolt

M8×25

23~27N.m

Steering column lower bracket fixing bolt

M8×50

23~27N.m

Steering column pivot and universal joint fixing bolt

M8×30

20~30N.m

Binding bolt of middle steering universal joint spline

M8×30

25~30N.m

Binding bolt of middle and lower universal joint

M8×30

25~30N.m

Binding bolt of steering gear input shaft

M8×30

25~30N.m

Mounting bolt of power steering gear

M12×65

75~85N.m

Steering gear steering knuckle tie rod and rack clamp nut

M18×1.5

122.6~142.2N.m

Steering gear steering knuckle tie rod and knuckle fixing nut

M12×1.5

35~45N.m

Steering pump and bracket

M8×1.2 5

20~30N.m

Steering pump and engine cylinder housing

M10×1.5

70~80N.m

Tension pulley lock nut

M10×1.25

20~30N.m

Power Steering Fluid Container

Oil pump Inlet Pipe

Steering Gear Oil inlet Pipe

Steering Gear Oil Return Pipe

Oil Pipe Bracket

Steering Gear Assembly

Oil Pump

T11 Service Manual Suspension and Steering

Joint Tightening Specification

Disassembly Drawing

1-15-17. Spoke trim cover

9. Steering upper shield

2. Steering wheel

10. Jacket fixing bracket

3. Steering wheel nut

12. Steering lower shield

4. Mounting bracket

13. Fixing bolt

5. Adjusting spring

14. Adjustable steering column

6. Upper universal joint universal joint

17. Horn hood assembly

7. Lower

18. Fixing bolt

8. Intermediate shaft

Application

Specification

Tightening torque

Two oil pipe joints of power steering gear

24.5~34.3N.m

Power steering high pressure hard tube and steering gear

joint

M18×1.5

27~33N.m

Power steering high-pressure oil pipe and steering pump

40~50N.m

Steering gear and oil return pipe joint

M16×1.5

27~33N.m

Steering Wheel with Steering Column