Chery QQ6 (S21) / S12LHD. Manual — part 14
53
6. Installation and Adjustment of
Headlamp
6.1. headlamp Installation Step
The installing steps of headlamp are
reverse to those for removal.
6.2. Introduction to headlamp function
6.2.1. Front view
See right figure:
1
Low beam light
2
Position light
3
High beam
4
Turn light
6.2.2. Back view
See right figure:
1
Low
beam
light
holder
2
Headlamp’s plug
3
High
beam
light
holder
4
High
beam
up/down
adjusting nut
5
High beam left/right adjusting nut
6
Low beam up/down adjusting nut
7
Low beam left/right adjusting nut
6.3. Adjustment of headlamp light
Headlamp uses half closed light combination type. So it is easy to be maintained; it is halogen
light with less mechanism and high luminous intensity, which will prolong bulb life.
The correctness of headlamp adjustment will influence the driving safety. So it needs special
device to adjust the beam. Pay attention to law regulations and verify the following items before
adjustment:
a.
Tire pressure should be conformity with standard;
b.
Car is unload (except for spare tire and equipped tools, and include driver weigh for
sedan);
c.
Park the car on horizontal road or workplace;
d.
The lens surface of headlamp should be clean;
e.
Check the power supplies if is working correctly, and the bulb installed correctly.
1
2
3
4
2
7
6
1
3
5
4
54
Adjust the governing mechanism equipped on
the lamps to implement the adjustment
rightward and leftward, upward and downward
of the lamp beam, according to the required
values in national standards. The coarse and
fine adjustment upward and downward is
integrated into one entity, which is located at
the upper edge of housing while the rightward
and leftward adjustment mechanism is located
at the central lower edge of the housing.
It needs take off headlamp cover to adjust right
headlamp. The left headlamp and right
headlamp adjusting mechanisms are arranged
symmetrically, with the same adjustment
method is the same.
6.3.3. The beam of headlamp can be adjusted
with the light adjusting nut or electric adjusting
pushbutton (if equipped).
6.3.3.1. Insert a cross screwdriver into the
corresponding adjustment hole to adjust the
beam.
6.3.3.2. Height of CHERY S21’s standard
headlamp reference center:
Low beam: 717 mm; High beam: 755 mm.
6.3.3.3. The headlamp light beam shall be
adjusted according to the data specified in the
national stardards:
When checking the dip beam (i.e. low beam)
headlamp position, project the headlamp on a
screen 10 m away, the dark and bright changing
line angle or central height shall be 0.7H – 0.9
H (H is the height of the headlamp reference
center, the same below) for passenger cars, it
shall be 0.6H – 0.8 H for other motor vehicles
(excluding transportation tractor combinations).
The horizontal deviation to the left of the
dipped headlamp for motor vehicles (except the
vehicle with only one headlamp) shall not
exceed 10 mm and the right deviation shall not
exceed 350 mm.
(From national standard)
6.3.3.5. Please input the standard data obtained
into the headlamp beam regulator for the
convenience to use in the furture.
55
7. Tail Lamp Removal Step
7.1. Remove the fix screws from the tail lamp
with a cross screwdriver.
7.2. Open the trunk, and lift up the carpet of
trunk.
7.3. Remove the upper seat fixing nuts from tail
lamp with a fix wrench.
7.4. Remove the lower seat fixing nuts from tail
lamp with a fix wrench.
7.5. Pull out the tail lamp harness connector,
and the take off the tail lamp assy.
56
Chapter 6 Disassembly/Reassembly of Ceiling
1. Preparation
Tools: socket wrench, cross screwdriver, flat
head screwdriver
2. Precautions
2.1. During the disassembly/reassembly, pay
more attention to the application of appropriate
force, without crude operation.
2.2. During the disassembly/reassembly of
interior ornaments, especially pay more
attention to the protection of surface ornaments
so as to avoid the damage of the ornaments.
3. Disassembly/Reassembly
of
Sun Visor
3.1. Removal Step
3.1.1. Loosen two fixing screws on left front
sun visor with a cross head screwdriver
Torque: 3±1Nm
3.1.2. Take off the front left sun visor.
3.2. Installation Step
The installing steps are reverse to those for
removal.
3.3. Refer to Disassembly/Reassembly of Front
Left Sun Visor for the disassembly/reassembly
of front right sun visor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст