Chery A15. Manual — part 196
Chery A15 Maintenance Manual
Chapter Six Disassembling and Installing of Door
and Window Glass
I. Front door glass
Disassembling and installing
Before disassembling the front door
glass, first remove the front inner
guard board and remove the waterproof film
according to the instructions.
1. Draw out the waterproof strips on internal
and external sides of the door and remove them from
inner rib of the central part of the door frame.
2. Place the glass in the middle of the doorframe.
Loosen the fixing notch between the window and
the bracket of the glass lifter.
While disassembling the glasses, maintain the
top of glass inclined outward.
Installing procedures for the glasses are in the
reversed order of the above. Remember don’t
fasten the set screws before the glasses have
been installed well.
II. Rear door glass
Disassembling and installing
Before disassembling the rear door
glass, first remove the front inner
Chery A15 Maintenance Manual
guard board and remove the waterproof
film according to the instructions.
1. Draw out the waterproof strips on internal
and external sides of the door and remove them from
inner rib of the central part of the door frame.
2. Place the glass in the middle of the doorframe.
Loosen the fixing notch between the window and
the bracket of the glass lifter.
3. While disassembling the glasses, maintain
the top of glass inclined outward.
Installing procedures for the glasses are in the
reversed order. Remember don’t fasten
the set screws before the glasses have been
installed well.
III. Rear quarter glass
Disassembling and installing
Remove the door guard board according to the
instructions before disassembling the rear quarter
glass.
1. Take out the central pressed part between
internal side and external side of the door and
disassemble it from the inner rib on the central part
of the door frame.
2. Loosen the set bolt between the central
guide way and the internal board of the door and
Chery A15 Maintenance Manual
remove the central guide way.
3. Draw the quarter glass outward and
remove it.
The installing procedures are in the reversed
order.
IV. Front door glass lifter
Disassembling and installing
Before disassembling the front door
glass lifter, first remove the front inner
guard board and the waterproof film
according to the instructions.
1. Loosen the six set screws between
the glass lifter and the inner guard board of the
door.
2. Pull down the plug of the lifter motor. Take out
the lifter motor from internal opening on the door.
Perform disassembling of glass lifter and disassembling
of the glass respectively.
Installing procedures are in the reversed order of the
above. Tighten the set bolt or set nut for glass
lifter with a torque of M=9
±
1N.m. Installing dimension
of glass bracket is 105mm as shown in the figure:
Chery A15 Maintenance Manual
105
After installing and adjusting, it must be assured that the glass can be lifted and
lowered stably and smoothly. No shaking, vibrating or shocking of glass is allowed.
Lifting-lowering period should be 3
±
1S.
V. Rear door glass lifter
Disassembling and installing
Before disassembling the rear door glass lifter, first remove the front inner
guard board and the waterproof film according to the instructions.
1. Loosen the six set screws between the glass lifter and the inner guard board of
the door.
2. Pull down the plug of the lifter motor. Take out the lifter motor from internal
opening on the door. Perform disassembling of glass lifter and disassembling
of the glass respectively.
Installing procedures are in the reversed order. Tighten the set bolt or set nut for
glass lifter with a torque of M=9
±
1N.m. Installing dimension of glass bracket is
105mm as shown in the figure:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст