Range Rover Body Repair Manual — part 29
CHASSIS AND BODY
41
REPAIR
GLASS CHANNEL - REAR DOOR
Service repair no - 76.31.17
Remove
1. Remove window lift motor/control panel
assembly.
See ELECTRICAL, Repair.
2. Remove 2 bolts securing channel to door and
remove channel.
Refit
3. Fit channel to door, secure with 2 bolts.
4. Refit window lift motor/control panel assembly.
See ELECTRICAL, Repair.
SEAL - REAR DOOR
Service repair no - 76.40.02
Remove
1. Open rear door.
2. Remove rear door carpet retainer.
3. Remove rear door aperture seal.
Refit
4. Fit rear door aperture seal.
5. Refit rear door carpet retainer.
6. Close rear door.
TRIM CASING - REAR DOOR
Service repair no - 76.34.04
Remove
1. Remove remote handle escutcheon.
76
CHASSIS AND BODY
NEW RANGE ROVER
42
REPAIR
2. Remove 2 screws securing trim casing.
3. Release 11 door trim casing retaining studs.
4. Disconnect rear door speaker connector.
Remove door trim casing.
Disassemble
5. Remove 11 trim casing retaining studs.
6. Remove 4 screws, remove upper speaker grille.
7. Remove 4 screws, remove lower speaker grille.
8. Remove 3 screws, remove arm rest.
9. Remove screw, remove retaining clamp and sill
button escutcheon.
CHASSIS AND BODY
43
REPAIR
10. Remove trim from door casing.
Assemble
11. Fit trim to door casing.
12. Fit sill button escutcheon and position retaining
clamp.
13. Tighten screw securing retaining clamp.
14. Fit arm rest to trim casing, secure with 3 screws.
15. Fit upper speaker grille to trim casing, secure
with 4 screws.
16. Fit lower speaker grille to trim casing, secure
with 4 screws.
17. Fit 11 trim casing retaining studs.
Refit
18. Fit and align door trim casing.
19. Secure 11 trim casing retaining studs.
20. Tighten 2 screws securing trim casing.
21. Fit remote handle escutcheon, tighten securing
screw.
OUTER WAIST SEAL - REAR DOOR
Service repair no - 76.31.54
Remove
1. Remove screw securing seal finisher to forward
edge of door.
2. Release seal finisher from clip at rear edge of
door.
3. Remove seal and finisher assembly.
4. Remove screw and securing clip.
Refit
5. Fit clip to door, secure with screw.
6. Fit seal and finisher assembly to door. Align at
forward edge, secure with screw.
76
CHASSIS AND BODY
NEW RANGE ROVER
44
REPAIR
RUBBING STRIPS & DOOR FINISHERS
Remove
CAUTION: When removing exterior trim,
NEVER lever directly against body panels.
Use an approved trim fork. Protect body
panel with suitable material, such as fabric
covered hardboard.
Rubbing Strip - Front Fender
1. Remove relevant wheel arch liner.
See this
section.
2. Remove nut securing forward edge of rubbing
strip.
3. Remove rubbing strip from single clip.
Rubbing Strip - Rear Quarter Panel
4. Release 5 clips securing rubbing strip. Remove
strip.
NOTE: Rearmost clip is unique.
Rubbing Strips - Front & Rear Doors
5. Remove nut securing rear of rubbing strip.
6. Front Door Rubbing Strip: Release 5 clips
securing rubbing strip.
7. Rear Door Rubbing Strip: Release 3 clips
securing rubbing strip.
8. Remove rubbing strips.
Lower Door Finishers
9. Remove screw securing rear of fininsher.
10. Front Door Finisher: Release 5 clips securing
rubbing strip.
11. Rear Door Finisher: Release 3 clips securing
rubbing strip.
12. Remove finishers.
Refit
13. Reverse removal procedure.
GLOVE BOX AND LID
Service repair no - 76.52.03 - Glove Box
Service repair no - 76.52.02 - Glove Box Lid
Service repair no - 76.52.13 - Glove Box Lid - Align
Remove
1. Remove centre screw from 2 scrivet fasteners.
Release closing panel for access to glove box
hinge fixings. Collect outer parts of fasteners
from closing panel.
2. Remove 2 bolts securing glove box hinges to
fascia frame.
3. Open glove box lid, remove 5 screws securing
glove box. Release glove box from fascia.
4. Disconnect glove box lamp multiplug.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст