Range Rover. Manual — part 243
CHASSIS AND BODY
67
REPAIR
HEADLINING - SLIDING ROOF
Service repair no - 76.64.15
Remove
1. Remove upper trims from ’A’,’B’,’D’ & ’E’ posts.
See this section.
2. Remove both sun visors.
See this section.
3. Remove grab handles.
See this section.
4. Remove parcel tray support trim.
See this
section.
5. Remove interior lamps.
See ELECTRICAL,
Repair.
6. Remove front courtesy lamp.
See
ELECTRICAL, Repair.
7. Remove ultrasonic sensor.
See ELECTRICAL,
Repair.
8. Fold down rear seat squabs. Recline front seat
squabs.
9. Release aperture sealing rubbers at tops of
doors and tailgate.
10. Release sun visor clip retaining screw cover
plugs.
11. Remove sun visor retaining clip screws. Remove
clips.
12. Remove sun roof aperture finisher.
13. Remove 2 headlining grab handle blanks.
14. Remove 2 studs securing rear of headlining.
15. With assistance remove headlining.
Refit
16. Reverse removal procedure.
76
CHASSIS AND BODY
NEW RANGE ROVER
68
REPAIR
SUNROOF DRAIN TUBE - FRONT
Service repair no - 76.82.21
Remove
1. Remove headlining.
See this section.
2. Remove wheel arch liner.
See this section.
3. Release drain tube from sunroof.
4. Release drain tube grommet from body behind
wheel arch liner.
5. Tie draw string to one end of drain tube and pull
tube from ’A’ post.
Refit
6. Tie draw string to new drain tube and pull
through ’A’ post.
7. Fit grommet to drain tube, secure to body.
8. Secure drain tube to sunroof.
9. Fit headlining.
See this section.
10. Refit wheel arch liner.
See this section.
CHASSIS AND BODY
69
REPAIR
SUNROOF DRAIN TUBE - REAR
Service repair no - 76.82.22
Remove
1. Remove headlining.
See this section.
NOTE: Ensure that parcel shelf support
panel is removed from side of drain tube
to be removed.
2. Release clip from drain tube.
3. Disconnect drain tube from sunroof.
4. Remove drain tube from wheel arch grommet.
Refit
5. Fit drain tube to sunroof, secure with clip.
6. Fit drain tube through wheel arch grommet.
7. Refit headlining.
See this section.
76
CHASSIS AND BODY
NEW RANGE ROVER
70
REPAIR
SUNROOF - WIND DEFLECTOR
Service repair no - 76.82.31
Remove
1. Open sunroof panel.
2. Remove 2 Torx screws securing wind deflector
to sunroof frame.
3. Remove wind deflector assembly.
4. Collect 2 spacer blocks and 2 nylon washers
from sunroof frame.
Refit
5. Position nylon washers and spacer blocks to
sunroof frame.
6. Align wind deflector assembly and secure with
Torx screws. Torque tighten Torx screws to
2 Nm (1.5 lbf.ft).
7. Close sunroof panel.
SUNROOF - PANEL
Service repair no - 76.82.05
Remove
1. Remove wind deflector.
See this section.
2. Tilt the sunroof panel.
3. Remove 2 mechanism covers by sliding
rearward.
4. Remove 4 Torx screws and 2 ’C’ clips,
connecting mechanism to sunroof panel.
5. Collect 2 slide brackets.
6. Release sunroof panel from locating pins.
7. Remove sunroof panel.
Refit
8. Lightly grease mechanism.
9. Position sunroof panel to locating pins.
10. Fit slide brackets.
11. Fit ’C’ clips and Torx screws, do not tighten at
this stage.
12. Adjust sunroof panel.
See Adjustment.
13. Fit wind deflector.
See this section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст