Range Rover. Manual — part 244
CHASSIS AND BODY
71
REPAIR
SUNROOF - SUNSHADE
Service repair no - 76.82.03
Remove
1. Remove sunroof panel.
See this section.
2. Remove wind deflector.
See this section.
3. Remove front map/courtesy lamp.
See
ELECTRICAL, Repair.
4. Wind mechanism (manually) in a clockwise
direction to open position using sunroof key.
5. Remove 2 screws securing RH guide assembly.
6. Remove 2 screws securing RH drive cable
locator.
7. Remove the drive cable locator.
8. Move LH guide assembly aside.
9. Remove sunshade.
10. Collect 4 slide clips.
Refit
11. Position sunshade to LH guide assembly and
insert clips.
12. Position RH guide assembly to sunshade and
insert clips.
13. Secure RH guide assembly with screws and
torque tighten front screws to
3 Nm (2.2 lbf.ft)
and rear screws to
1.5 Nm (1.1 lbf.ft).
14. Position drive cable locator and secure with
screws and torque tighten screws to
3 Nm (2.2
lbf.ft).
15. Fit wind deflector.
See this section.
16. Wind mechanism in an anti-clockwise direction
to closed position using sunroof key.
17. Fit front map/courtesy lamp.
See ELECTRICAL,
Repair.
18. Fit sunroof panel.
See this section.
76
CHASSIS AND BODY
NEW RANGE ROVER
72
REPAIR
SUNROOF - MOTOR
Service repair no - 76.82.53
Remove
1. Close sunroof panel.
2. Remove front map/courtesy lamp.
See
ELECTRICAL, Repair.
3. Remove 3 screws securing sunroof motor to
mounting bracket.
4. Remove motor and collect spacers.
5. Remove sunroof motor multiplug from mounting
clip and disconnect multiplug.
Refit
6. If position of sunroof motor is not known,
synchronise motor to closed position before
fitment as follows:
Connect motor to motor multiplug. With ignition
in position I or II, operate sunroof switch to open
position. Press and hold sunroof switch to closed
position until motor stops.
7. Connect motor multiplug and secure to mounting
clip.
8. Fit spacers to motor.
9. Position motor to mounting bracket and secure
with screws. Torque tighten screws to
2 Nm (1.5
lbf.ft).
10. Fit front map/courtesy lamp.
See ELECTRICAL,
Repair.
SUNROOF - CABLE
Service repair no - 76.82.14
Remove
1. Remove sunroof panel.
See this section.
2. Remove sunroof motor.
See this section.
3. Remove 2 screws securing the cable locator.
4. Remove cable locator.
5. Remove cable from slide.
6. Withdraw cable from tube.
Refit
7. Grease cable.
8. Feed cable into tube and locate into slide.
9. Position locator and secure with screws. Torque
tighten screws to
3 Nm (2.2 lbf.ft).
10. Fit the sunroof motor.
See this section.
11. Fit the sunroof panel.
See this section.
CHASSIS AND BODY
73
REPAIR
SUN VISOR
Service repair no - 76.10.47
Remove
1. Release visor from clip.
2. Remove 3 visor retaining screws.
3. Disconnect visor lamp multiplug.
4. Remove visor.
5. Remove clip if required. Carefully lever plastic
tag down.
6. Remove screw, remove clip.
Refit
7. Reverse removal procedure.
SILL FINISHER
Service repair no - 76.43.84
Remove
1. Remove 3 screws securing front tread plate.
2. Remove 2 screws securing rear tread plate.
3. Remove trim stud securing rear of sill finisher.
4. Release 8 clips securing finisher to sill.
5. Remove sill finisher.
Refit
6. Renew clips as necessary.
7. Reverse removal procedure.
76
CHASSIS AND BODY
NEW RANGE ROVER
74
REPAIR
TAILGATE - UPPER
Service repair no - 76.28.29
Remove
1. Remove both ’E’ post finishers.
2. Remove 2 trim fixing studs. Release headlining
from ’E’ posts.
3. Release 4 turn buckles securing access panel to
LH side load space trim. Remove panel.
4. Locate rear screen washer non-return valve.
Disconnect tailgate feed tube from valve.
5. Attach draw string to tube to aid re-assembly.
6. Release tailgate harness protective sleeve from
roof panel.
7. Disconnect 3 tailgate harness multiplugs from
body harness. Pull plugs out through hole in roof
panel.
8. Pull screen washer tube out through hole in roof
panel. Disconnect draw string.
9. Mark outline of hinge on tailgate to aid
re-assembly.
10. Apply protective tape to roof panel before
releasing tailgate.
11. With assistance, disconnect gas struts from
tailgate.
12. With assistance, remove 4 bolts securing hinges
to tailgate. Remove tailgate.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст