Range Rover. Manual — part 232
CHASSIS AND BODY
23
REPAIR
27. Remove 3 scrivets securing lower fascia closing
panel to passenger’s side of fascia.
28. Release closing panel and release diagnostic
connector from panel.
29. Release door aperture seal adjacent to ’A’ post
lower trim panels.
30. Remove screw securing each ’A’ post lower trim
panel to ’A’ post.
31. Release ’A’ post lower trim panels from sprag
clip and remove panels.
32. Remove fuse box cover from driver’s seat base
trim.
33. Remove screw and 3 trim studs securing seat
base trim to body and remove seat base trim.
34. Release 4 sprag clips securing driver’s side
carpet retainer to body and remove carpet
retainer.
35. Disconnect 3 multiplugs from Body Electrical
Control Module (BeCM).
36. Position carpet aside and disconnect multiplug
from rear of BeCM.
76
CHASSIS AND BODY
NEW RANGE ROVER
24
REPAIR
37. Remove captive nut securing earth wires to
driver’s side lower ’A’ post and release 3
additional earth wires.
38. Disconnect 3 multiplugs at base of driver’s side
’A’ post.
39. Release harness from driver’s side carpet and
position to fascia to avoid snagging.
40. Disconnect multiplugs from clutch and 2 brake
pedal switches.
41. Disconnect vacuum hose from clutch and brake
pedal switches.
42. Disconnect 2 multiplugs at base of passenger’s
side ’A’ post.
43. Remove 2 nuts securing fascia to ’A’ post and
transmission tunnel bracket, passenger’s side
44. Remove 2 nuts securing fascia to ’A’ post and
transmission tunnel bracket, driver’s side.
CHASSIS AND BODY
25
REPAIR
45. Remove 4 tube bolts securing fascia assembly
to scuttle panel.
46. Disconnect 2 evaporator drain hoses from
evaporator.
47. Using assistance, carefully manoeuvre fascia
assembly through the driver’s door aperture.
Position the fascia on a work surface with a soft
covering and support on suitable wooden blocks.
48. Collect 2 ducts connecting rear heating pipes to
fascia assembly.
Refit
49. Tape intake duct seals inside blower duct to aid
fitment.
50. Fit guide pins LRT-76-001 to outer fascia studs.
51. With assistance, manoeuvre fascia assembly
through driver’s door aperture and locate guide
pins to scuttle panel.
NOTE: Assistance from a third person may
be required to guide heater pipes through
bulkhead.
52. Fit one tube bolt securing fascia to scuttle panel
but do not tighten.
53. Fit nuts securing fascia to lower ’A’ posts and
tighten to
25 Nm. (18 lbf.ft)
54. Fit nuts securing fascia to transmission tunnel
brackets and tighten to
25 Nm. (18 lbf.ft)
55. Remove LRT-76-001.
56. Fit remaining tube bolts securing fascia to scuttle
panel and tighten to
25 Nm. (18 lbf.ft)
57. Fit fascia centre bracket, fit bolts and tighten to
25 Nm. (18 lbf.ft)
58. Connect evaporator drain hoses to evaporator.
59. Fit ducts connecting rear heating pipes to fascia
assembly.
60. Fit gear lever to gearbox remote, fit bolts and
tighten to
25 Nm. (18 lbf.ft)
61. Fit gear lever gaiter and ring to transmission
tunnel and secure with nuts.
62. Connect high/low switch multiplug.
63. Position SRS harness to transmission tunnel.
64. Connect multiplug to airbag DCU. Ensure
connector latching mechanism is correctly
engaged.
65. Fit transmission tunnel insulation pad to
transmission tunnel and position multiplugs
through pad.
66. Fit radio.
See ELECTRICAL, Repair.
67. Connect multiplugs at base of passenger’s side
’A’ post.
68. Fit passenger’s side ’A’ post lower trim panel
and secure with screw.
69. Engage door aperture seal to door aperture.
70. Position fascia lower closing panel and engage
diagnostic connector to panel.
71. Position closing panel to fascia and secure with
scrivets.
72. Connect vacuum hose to clutch and brake pedal
switches.
73. Connect multiplugs to clutch and brake pedal
switches.
76
CHASSIS AND BODY
NEW RANGE ROVER
26
REPAIR
74. Position harness to driver’s side carpet.
75. Connect multiplugs to BeCM.
76. Connect multiplugs at base to driver’s side ’A’
post.
77. Position earth wires to ’A’ post stud, fit and
secure captive nut.
78. Fit driver’s side carpet retainer and engage to
clips.
79. Fit seat base trim and secure with trim studs and
screw.
80. Fit seat base fuse box cover.
81. Fit driver’s side lower ’A’ post trim and secure
with screw.
82. Fit steering column.
See STEERING, Repair.
83. Fit radio.
See ELECTRICAL, Repair.
84. Fit centre console.
See this section.
85. Remove tape from heater intake ducts.
86. Engage heater intake seals to scuttle apertures.
87. Fit heater intake housings and secure with
screws.
88. Fit pollen filters to intake housings.
89. Fit wiper motor and linkage.
See WIPERS AND
WASHERS, Repair.
90. Fit scuttle side panel to scuttle and secure with
bolts.
91. Connect heated screen multiplug and engage
multiplug to scuttle side panel bracket.
92. Remove caps from heater matrix pipes.
93. Engage heater matrix grommet to bulkhead
aperture.
94. Connect heater hoses to heater matrix and
secure with clips.
95. Remove caps from air conditioning pipes and
TXV.
96. Lubricate NEW ’O’ ring seals with clean
compressor oil and fit to air conditioning pipes.
97. Connect air conditioning pipes to TXV, position
clamp and fit bolt.
98. Tighten clamp bolt to
6 Nm. (4 lbf.ft)
99. Charge air conditioning system.
See AIR
CONDITIONING, Adjustment.
100. Fill coolant system.
See COOLING SYSTEM,
Repair.
101. Connect both battery terminals, earth lead last.
PANELS - VENEERED - FASCIA
Service repair no - 76.46.24
Remove
1. Drivers side: Remove fascia closing panel.
See
this section.
2. With suitable protection against fascia, carefully
lever veneered panel away from fascia to
release 2 fixing studs.
3. Remove fixing stud inserts.
4. Passenger side: Open glove box.
5. With suitable protection against fascia, carefully
lever veneered panel away from fascia to
release 4 fixings studs.
6. Remove fixing stud inserts.
7. Remove glove box lock bezel from veneered
panel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст