Range Rover. Manual — part 233
CHASSIS AND BODY
27
REPAIR
Refit
8. Passenger side: Fit glove box lock bezel.
9. Fit fixing stud inserts to fascia.
10. Fit veneered panel to fascia.
11. Close glove box.
12. Drivers side: Fit fixing stud inserts to fascia.
13. Fit veneered panel to fascia.
14. Drivers side: Fit fascia closing panel.
See this
section.
PANEL - FASCIA CLOSING
Service repair no - 76.46.28
Remove
1. Release steering column adjustment lock, raise
and extend column for access to panel upper
screws.
2. Remove 4 screw covers from fascia closing
panel and remove screws.
3. Remove 2 screws securing top of closing panel.
4. Disconnect air tube and remove closing panel.
Refit
5. Position closing panel and connect air tube.
6. Fit closing panel to fascia and secure with
screws.
7. Fit screw covers and reposition steering column.
76
CHASSIS AND BODY
NEW RANGE ROVER
28
REPAIR
FRONT DOOR ASSEMBLY
Service repair no - 76.28.01/99
Remove
1. Release door harness protective sleeve from ’A’
post.
2. Disconnect door harness multiplugs.
3. Remove door check strap retaining pin.
CAUTION: Apply protective tape to ’A’
post before drifting out retaining pin.
4. Remove door hinge pin retaining clips.
5. With assistance, remove door assembly.
Refit
6. With assistance, position door on hinges. Fit
retaining clips.
7. Align door check strap. Fit retaining pin.
8. Remove protective tape from ’A’ post.
9. Connect harness multiplugs. Secure protective
sleeve to ’A’ post.
10. If necessary adjust door.
See Adjustment.
GLASS - FRONT DOOR
Service repair no - 76.31.01
Remove
1. Remove front door outer waist seal.
See this
section.
2. Remove front door plastic sheet.
See this
section.
3. Turn ignition ON.
4. Lower glass approximately 120mm (5 in.)
Remove rear regulator arm retaining clip.
5. Lower glass to align forward clip with the
regulator plate lower retaining rivet. Turn ignition
OFF.
CHASSIS AND BODY
29
REPAIR
6. Remove front lower fixing clip.
7. Remove nut securing bracket to vertical slide.
8. Release bracket from slide.
CAUTION: Chock glass with wooden
block, or retain with tape, to prevent glass
dropping when regulator arms are
released.
9. Using a suitable lever, release 2 regulator arms
from glass lower fixings.
10. Support weight of glass. Remove wooden chock
or tape.
11. Rotate glass anti-clockwise to release from
runners.
12. Remove front door glass.
Refit
13. Refit front door glass.
14. Rotate glass anti-clockwise, fit to runners.
15. Secure glass fixings to regulator arms.
16. Position glass bracket to vertical runner, fit
retaining nut.
17. Fit clip securing regulator arm to glass runner.
18. Turn ignition ON.
19. Raise door glass approximately 120mm (5 in.)
Fit rear glass retaining clip.
20. Raise door glass.
21. Turn ignition OFF.
22. Fit front door plastic sheet.
See this section.
23. Fit front door outer waist seal.
See this section.
76
CHASSIS AND BODY
NEW RANGE ROVER
30
REPAIR
GLASS REGULATOR - FRONT DOOR
Service repair no - 76.31.45
Remove
1. Remove front door glass.
See this section.
2. Disconnect window lift motor harness connector.
3. Remove rivet securing regulator runner to door
panel.
4. Remove 3 rivets.
5. Remove regulator assembly.
Refit
6. Reverse removal procedure.
LATCH - FRONT DOOR
Service repair no - 76.37.12
Remove
1. Remove front door trim casing.
See this
section.
2. Release rear of plastic sheet.
3. Release retaining clip, private lock to latch
operating rod, at latch end.
4. Release control rod from latch.
5. Release retaining clip, outside handle to latch
operating rod, at latch end.
6. Release control rod from latch.
7. Disconnect 2 latch motor multiplugs.
8. Remove door sill button from operating rod.
9. Release remote handle to latch operating cable
from clip.
10. Remove 3 screws securing latch.
11. Release latch from door.
12. Remove sill button operating rod from latch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст