Range Rover Classic. Manual — part 154
CHASSIS AND BODY
39
REPAIR
7. Pull door seal away to remove lower ’B’ post
trim.
8. Remove seat belt through slot in lower ’B’ post
trim.
9. Remove bolt and spring washer from inertia reel
assembly to ’B’ post.
10. Disconnect electrical plug and remove bolt
securing buckle to seat base.
Refit
11. Reverse removal procedure. Ensure belts are
not twisted. Tighten bolts to
25Nm.
REAR SEAT BELT
Service repair no - 76.73.18
Remove
1. Remove plastic cover from upper guide bracket.
Remove bolt, spacer, plain and wavy washer.
2. Unclip cover from inertia reel assembly. Remove
bolt, spring washer. Place reel to one side.
3. Remove plastic cover and bolt securing belt
assembly to wheel arch.
4. Remove belt assembly.
76
CHASSIS AND BODY
40
REPAIR
5. Remove bolt and plain washer securing belt
bracket to load space floor.
6. Centre lap strap only: Remove bolts securing lap
strap and buckle assembly and withdraw both
components.
Refit
7. Reverse removal procedure. Ensure belts are
not twisted. Tighten bolts to
25Nm.
CENTRE CONSOLE
Service repair no - 76.52.00
Service repair no - 76.25.09 Veneer panel
Service repair no - 76.25.25 Switch panel
Remove
1. Disconnect battery negative lead.
2. Remove cigar lighter.
3. Release gaiter and unscrew transfer gear lever
knob.
4. Lift at front and remove finisher from automatic
gear selector housing.
5. Lift at front and remove veneer panel.
6. Remove switch panel veneer.
7. Remove 4 screws securing switch panel.
8. Withdraw switch panel from console.
9. Disconnect multiplugs from 9 switches.
10. Remove switch panel assembly.
CHASSIS AND BODY
41
REPAIR
11. Open glovebox lid.
12. Remove 5 screws securing console.
13. Release 2 clips, securing front of console to
bracket.
14. Release handbrake gaiter from console.
15. Remove spring clip (from RH side) and clevis pin
securing cable to handbrake lever.
16. Lift handbrake lever and manoeuvre console
slightly away from tunnel.
17. Disconnect Lucar connectors from cigar lighter.
18. Lift console assembly over handbrake and gear
levers and remove from vehicle.
Refit
19. Reverse removal procedure. Ensure electrical
plugs are fitted correctly and wiring is not
trapped.
20. Lubricate handbrake clevis pin.
DRINKS TRAY
Service repair no - 76.46.41
Remove
1. Disconnect battery negative lead.
2. Remove ash tray.
3. Release air suspension switch panel from dash
and position below aperture.
See
ELECTRICAL, Repair, Air Suspension
Switches and Bulbs
4. Remove 6 screws securing drinks tray to dash.
5. Remove drinks tray assembly.
Refit
6. Reverse removal procedure.
76
CHASSIS AND BODY
42
REPAIR
DASH PANEL CENTRAL LOUVRE PANEL
Service repair no - 76.46.42
Remove
1. Disconnect battery negative lead.
2. Remove radio from mounting frame.
See
ELECTRICAL, Repair, Radio
3. Remove clock assembly.
4. Remove drinks tray.
See Drinks Tray
5. Remove heater control unit.
See HEATING
AND VENTILATION, Repair, Heater Control
Unit
6. Remove centre console assembly.
See Centre
Console
7. Remove 3 heater control knobs and blower
switch knob.
8. Undo 2 screws and remove heater graphic
display panel.
9. Remove 4 screws securing heater control unit to
panel.
10. Push heater control unit through panel.
11. Inside auxiliary switch panel aperture, remove 2
screws securing panel.
12. Inside clock aperture, remove 2 screws securing
panel.
13. Slacken 2 screws securing upper panel.
14. Manoeuvre LED light panel from panel,
disconnect bulb holder and remove light panel.
15. Remove 2 screws securing louvre panel.
16. Remove louvre panel from dash panel.
Refit
CAUTION: When refitting avoid trapping of
electrical wiring.
17. Reverse removal procedure. Place louvre panel
in position, ensure wiring looms are free and
multiplugs and connectors are through their
apertures
18. Check function of all switches and controls.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст