Range Rover Classic. Manual — part 152
CHASSIS AND BODY
31
REPAIR
REAR DOOR LOCK AND HANDLE ASSEMBLY
Service repair no - 76.37.48
Outside door release handle to lock
1. Disconnect connecting rod at rear of door outer
release handle.
2. Rotate rod to adjust operating length as
required, so that door release occurs before
maximum handle movement.
REAR DOOR GLASS AND REGULATOR
Service repair no - 76.31.02 / 76.31.46
Remove
1. Fully close window and secure with tape.
2. Disconnect battery negative lead.
3. Remove trim panel.
See Rear Door - Trim
Panel
4. Remove sill button.
5. Remove plastic vapour barrier.
6. Remove window lift motor.
See ELECTRICAL,
Repair, Window Lift Motor - Rear Doors
7. Remove four window regulator screws with
shakeproof washers.
8. Disengage lifting arm stud from channel and
remove window regulator.
76
CHASSIS AND BODY
32
REPAIR
9. Remove waist rail seal from top of door panel.
10. Remove bolt, spring and plain washers which
secures bottom of door frame.
11. Remove bolt, spring and plain washer from door
frame, as shown.
12. Remove two bolts, spring and plain washers
from both door faces.
13. Remove door frame with glass in position.
14. Remove tape and slide glass out of door frame.
Refit
15. Reverse removal procedure. When fitting door
frame align to suit door opening. Then tighten
door frame securing bolts.
REAR QUARTER LIGHT GLASS
Service repair no - 76.81.25
Remove
1. Remove and discard moulding from flange
around opening.
2. Clean area where moulding contacts body.
Refit
3. Fit new moulding to glass.
4. Fit a draw cord around moulding retaining
channel.
5. Coat flange around opening with liquid soap to
aid assembly.
6. Hold glass and moulding to opening. Site draw
cords inside vehicle.
7. With assistance push glass and moulding into
opening. Pull draw cords enabling seal to ride
over flange.
8. Ensure interior trim fits under moulding.
9. Ensure moulding is settled and contacts body.
CHASSIS AND BODY
33
REPAIR
FRONT SEAT ELECTRICAL
Service repair no - 76.77.01
Remove
1. Remove screw securing seat side trim panel and
remove panel.
2. Remove three screws from seat front trim panel.
Remove screw from top of trim panel to seat
base, located below seat base cushion. Remove
panel.
3. Remove three fixings securing cushion side trim
panel. Remove panel. Remove bolt securing
seat belt.
4. Move seat to rearward position. If seat will not
move.
See ELECTRICAL, Repair, Electrical
Seat Failure
5. Remove two screws at front of each slide
channel.
6. Move seat to most forward position.
7. Remove four screws at rear of each slide
channel.
8. Disconnect battery negative lead.
9. Disconnect all electrical multiplugs to seat
electrics.
10. Remove seat.
Refit
11. Reverse removal procedure. Arrange electrical
leads so they can not become trapped by seat
slide mechanism.
76
CHASSIS AND BODY
34
REPAIR
FRONT SEAT MANUAL
Service repair no - 76.70.01
Remove
1. Disconnect battery negative lead.
2. Remove two screws securing side panel and
remove panel.
3. Remove three screws from front trim panel.
Remove screw from top of trim panel to seat
base. Remove panel.
4. Remove bolt and washer securing seat belt.
5. Move seat to rearward position.
6. Remove two screws at front of each slide
channel.
7. Move seat to most forward position.
8. Remove four screws at rear of each slide
channel.
9. Remove seat, retaining spacers between slide
channel and seat base.
Refit
10. Reverse removal procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст