Jeep Grand Cherokee WK. Manual — part 1613
6. Remove the upper B-pillar trim panel, (Refer to 23
-
BODY/INTERIOR/B-PILLAR
UPPER
TRIM
-
REMOVAL).
7. Open the access door on the lower B-pillar trim
panel.
8. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the lower B-pillar trim
panel to the B-pillar.
9. Remove the seat belt from the lower B-pillar trim
panel
through
the
access
door
opening
and
remove the trim panel.
INSTALLATION
1. Route the seat belt through the access door open-
ing in the lower B-pillar trim panel.
2. Position the lower B-pillar trim panel to the B-pillar
and engage the retaining tabs that secure the trim
panel to the B-pillar.
23 - 110
INTERIOR
WK
3. Install the upper B-pillar trim panel, (Refer to 23 -
BODY/INTERIOR/B-PILLAR
UPPER
TRIM
-
INSTALLATION).
4. Position the seat belt lower anchor to the mounting
hole on the outboard side of the front seat cushion
frame. Be certain that the seat belt webbing
between the turning loop and the lower anchor is
not twisted.
5. Install the screw (2) that secures the lower anchor
to the seat. Tighten the screw to 39 N·m (29 ft.
lbs.).
6. Reinstall the lower anchor cover (1) onto the front
seat cushion outboard side shield.
WK
INTERIOR
23 - 111
7. Position the seat belt aside and close the access door on the lower B-pillar trim panel.
8. Install the rear door sill scuff plate, (Refer to 23 - BODY/INTERIOR/DOOR SILL SCUFF PLATE - INSTALLA-
TION).
9. Install the front door sill scuff plate, (Refer to 23 - BODY/INTERIOR/DOOR SILL SCUFF PLATE -
INSTALLATION).
B-PILLAR UPPER TRIM
REMOVAL
1. Firmly grasp the lower end of the turning loop trim
cover on the upper B-pillar and pull it straight out to
unsnap it from the height adjuster, then lift the bot-
tom of the cover upward and pull outward to disen-
gage the upper tabs from the adjuster.
2. Remove the screw that secures the seat belt turn-
ing loop to the height adjuster.
3. Remove the seat belt turning loop from the height
adjuster and position the seat belt out of the way.
4. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper B-pillar trim
panel to the B-pillar and remove the trim panel.
23 - 112
INTERIOR
WK
INSTALLATION
1. Position the upper B-pillar trim panel to the B-pillar
and engage the retaining tabs that secure the trim
panel to the B-pillar.
2. Position the seat belt turning loop onto the height
adjuster on the upper B-pillar. Be certain that the
seat belt webbing between the retractor and the
turning loop is not twisted.
3. Install the screw that secures the turning loop to
the height adjuster. Tighten the screw to 39 N·m
(29 ft. lbs.).
4. Insert the upper tabs of the turning loop trim cover
into the slots of the height adjuster on the upper
B-pillar, then lower the bottom of the cover and use
hand pressure to press firmly and evenly on the
cover until it snaps into place.
C-PILLAR UPPER TRIM
REMOVAL
1. Remove the bolts that secure the rear passenger seat cushion to the floor, (Refer to 23 - BODY/SEATS/SEAT
CUSHION - REMOVAL).
2. Position the rear passenger seat cushion to gain access to the bolt that secures the rear outboard seat belt lower
anchor and the rear seat back bracket to the rear floor panel.
3. Loosen the bolt that secures the rear outboard seat belt lower anchor and the rear seat back bracket to the rear
floor panel.
4. Disengage the lower anchor from the loosened bolt.
5. Using a trim stick C-4755 or equivalent, disengage the retaining tabs that secure the upper C-pillar trim panel to
the retaining clips in the C-pillar.
6. Remove the seat belt from the upper C-pillar trim panel through the slot provided and remove the upper C-pillar
trim panel.
INSTALLATION
1. Route the seat belt through the slot in the upper C-pillar trim panel.
2. Position the locating tabs on the bottom of the upper C-pillar trim panel into the slots in the top of the quarter trim
panel.
3. Align the retaining tabs on the upper C-pillar trim panel with the retaining clips in the C-pillar and engage the
retaining tabs that secure the trim panel to the C-pillar.
4. Engage the seat belt lower anchor under the loosened bolt that secures the lower anchor and the rear seat back
bracket to the rear floor panel. Be certain the seat belt webbing between the turning loop and the lower anchor
is not twisted.
5. Tighten the bolt that secures the lower anchor and the rear seat back bracket to the rear floor panel. Tighten the
bolt to 50 N·m (37 ft. lbs.).
6. Reinstall the rear seat cushion into the vehicle. (Refer to 23 - BODY/SEATS/REAR SEAT CUSHION -
INSTALLATION).
WK
INTERIOR
23 - 113
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст