Engine Iveco C10/C13/C78/Cursor 13/Cursor 78. Manual — part 66
SELECTING THE MAIN BEARING SHELLS (Journals with nominal diameter)
After reading off the data, for each of the main journals, on the crankcase and crankshaft, you choose the type of bearing shells
to use according to the following table:
STD.
1
2
3
1
2
3
green
green
red
red
red
red
green
green
green
green
red
red
green
green
green
green
green
green
Figure 27
22
SECTION 4 - OVERHAUL AND TECHNICAL SPECIFICATIONS
green/black
SELECTING THE MAIN BEARING SHELLS (GROUND JOURNALS)
If the journals have been ground, the procedure described so far cannot be applied.
In this case, it is necessary to check that the new diameter of the journals is as shown in the table and to mount the only type
of bearing shell envisaged for the relevant undersizing.
-0.127
1
2
3
99.843
99.852
green/black
green/black
green/black
green/black
green/black
green/black
red/black
red/black
green/black
green/black
green/black
red/black
red/black
red/black
red/black
green/black
green/black
99.853
99.862
99.863
99.873
1
2
3
red/black =
3.028 to 3.037 mm
green/black =
3.038 to 3.047 mm
-0.254
1
2
3
99.726
99.746
red
red
red
red
red
red
red =
3.092 to 3.102 mm
-0.508
1
2
3
93.468
93.508
red
red
red
red
red
red
red =
3.219 to 3.229 mm
Figure 28
SECTION 4 - OVERHAUL AND TECHNICAL SPECIFICATIONS
23
Figure 29
SELECTING THE BIG END BEARING SHELLS
(JOURNALS WITH NOMINAL DIAMETER)
There are three markings on the body of the connecting rod
in the position shown in the view from ”A”:
Letter indicating the class of weight:
A
=
4024 to 4054 g.
B
=
4055 to 4085 g.
C
=
4086 to 4116 g.
Number indicating the selection of the diameter of the
big end bearing seat:
1
=
87.000 to 87.010 mm
2
=
87.011 to 87.020 mm
3
=
87.021 to 87.030 mm
Numbers identifying the cap-connecting rod coupling.
1
2
3
The number, indicating the class of diameter of the bearing
shell seat may be 1, 2 o 3.
Determine the type of big end bearing to fit on each journal
by following the indications in the table (Figure 30).
47557
VIEW FROM “A”
STD.
1
2
3
1
2
3
green
green
red
green
red
red
red
green
green
green
green
green
green
green
green
green
red
red
Class
Figure 30
24
SECTION 4 - OVERHAUL AND TECHNICAL SPECIFICATIONS
Figure 31
green/black
SELECTING BIG END BEARING SHELLS (GROUND JOURNALS)
If the journals have been ground, the procedure described so far cannot be applied.
In this case, it is necessary to check (for each of the undersizings) which field of tolerance includes the new diameter of the
crankpins and to mount the bearing shells identified with the relevant table.
-0.127
1
2
3
82.843
82.852
green/black
green/black
green/black
green/black
green/black
green/black
green/black
red/black
green/black
green/black
green/black
red/black
red/black
green/black
red/black
green/black
green/black
82.853
82.862
82.863
82.873
1
2
3
red/black =
2.044 to 2.053 mm
green/black =
2.033 to 2.043 mm
-0.254
1
2
3
82.726
82.735
red
green
green
red
green
green
red
=
2.097 to 2.107 mm
green =
2.108 to 2.117 mm
-0.508
1
2
3
82.472
82.481
red
green
green
red
green
green
red
red
green
red
red
green
82.482
82.492
red
red
green
red
red
green
red
=
2.224 to 2.234 mm
green =
2.235 to 2.244 mm
82.736
82.746
SECTION 4 - OVERHAUL AND TECHNICAL SPECIFICATIONS
25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст