Geely Diagnosis Flow. Manual part — 67
Geely Diagnosis Flow. Manual part - 67
265
No. 190 CD-player fails to work when activating
Malfunction Cause
Solution
Power source circuit
malfunction or fuse
damaged;
Inspect +B and GND, which normal value shall be 10V to 14V. When ACC
and GND ignition switch locating at ACC or ON, the voltage shall be 10V to
14V. In common condition, GND and vehicle earth lead shall be conducted. If
it indicates no powers supply, then check whether the fuse is burnt or not,
and replace it if necessary.
CD-player power switch
malfunction or damage
①
Check the power switch on CD panel; operate the power switch by hand, if
there is no response then replace the CD-player
CD-player fails to
work when
activating
Internal CD-player power
source circuit
malfunction
④
Check the voltage of internal CD-player power source end, if the value is
between 10~14V as normal, then replace the CD-player assembly
No. 191 CD-player keeps soundless under all modes
Malfunction Cause
Solution
①
CD-player power
source malfunction
Inspect +B and GND, which normal value shall be 10V to 14V. When ACC and
GND ignition switch locating at ACC or ON, the voltage shall be 10V to 14V. If it
indicates no powers supply, then shall confirm whether the fuse is burnt or not,
and replace it if necessary.
②
Loudspeaker
malfunction
Check whether the appearance of loudspeaker is damaged, as well as the coil
whether it is burnt.
Method: Measure the resistance by multimeter setting at ohms range, and the
value shall be 4 Ohm, if it indicates to infinite, then the loudspeaker is burnt and
need to be replaced.
③
Wires and
connector
Check loudspeaker and CD-player connection whether there is open/short
circuit. Measure two ends of same colour respectively by multimeter setting to
Ohms range, and the value shall be 0 which means conducted. Check
CD-player rear plug whether it is loose, and the power source voltage whether
it is normal. In generally condition, GND and body earthlead shall be
conducted.
CD-player keeps
soundless under all
modes
④
CD-player sound
controller damaged
Check whether CD-player sound controller is damaged, and track adjustment
whether it is correct, as well as sound adjusting variable voltage regulator
whether it is badly worn. Replace CD-player assembly.
CD-player fails to work when activating
External CD-player power
source
CD-player switch
Internal CD-player power source circuit
Abnormal
Abnormal
Abnormal
Inspect the circuit and replace the fuse
Replace CD assembly
Replace CD assembly
Normal
Normal
266
CD-player keeps soundless under all modes
Check wires, connector and
power source voltage.
Check LCD screen illumination
CD –player power
source malfunction
Check and replace the fuse
Check loudspeaker
Replace loudspeaker
Replace CD-player assembly
Replace CD-player assembly
Check CD-player sound
adjusting button
Internal CD-player circuit
Normal
Normal
Normal
Normal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Replace CD-player assembly
267
No. 192 CD-player/radio gains no power
Malfunction Cause
Solution
①
Vehicle ignition switch closed
①
Turn ignition device to ON or ACC position
②
Fuse burnt
②
Replace fuse of same specification
③
Power source output line loose
③
Replace it with new connector of same
specification if abnormal
④
Dirt in connector conducting point.
④
Clean the conducting point with special cleaning
solution or replace it with a new one.
⑤
Connector wire core disconnected
(open circuit)
⑤
Check loudspeaker output line with multimeter
whether it is disconnected, replace it with new
connector of same specification if necessary
⑥
Poor fuse contact (open circuit
sometimes)
⑥
Connect vehicle battery earthlead and speaker
housing by lead wire, if CD-player regains normal
operation, which indicates the earth lead open
circuit, then replace it with new connector of same
specification.
⑦
Connector earth lead open circuit
⑦
Replace it with new connector of same
specification
CD-player gains no power
when pressing POWER
button, after the ignition
switch opened,
⑧
Internal CD-player/radio short circuit
⑧
Replace CD-player/radio assembly
Replace with fuse of same specification
CD-player/radio gains no power
Vehicle ignition switch closed
Turn to ON or ACC position
Fuse burnt
Replace with fuse of same specification
Power source output line loose
Replace connector with same specification
Dirt in connector conducting point
Clean or replace connector with same
specification
Connector wire core disconnected (open circuit)
Poor fuse contact (open circuit
sometimes)
Replace connector with same specification
Replace connector with same specification
Replace CD-player/radio
assembly
Internal CD-player/radio short circuit
Connector earth lead open circuit
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Short circuit
268
No. 193 A loudspeaker of CD-player/radio is soundless
Malfunction Cause
Solution
Panel function setting inaptitude
In SEL menu, on panel, BAL and FDA shall be set to 0
Loudspeaker damaged
Replace loudspeaker of same specification. (Note: Firstly,
connect the output line of front right loudspeaker to the other
one, and check the sound output, which can indicate whether
the loudspeaker is broken.)
Loudspeaker output line wrong
connected
Check output line connection whether it is correct. (Please
refer to the connecting method shows on nameplate.)
Connector conducting point and
output line connection containing
dirt or oxide.
Clean the connector with special cleaning solution or replace
it with a new one of same specification.
Connector wire core disconnected
(open circuit)
Measure loudspeaker output line by multimeter, whether it is
disconnected. And replace it with a new one of same
specification when necessary.
A loudspeaker is
soundless when CD/FM
operating
Internal CD-player/radio
loudspeaker output disconnected
Replace CD-player/radio assembly
Loudspeaker outputline
connection oxide
A loudspeaker of CD-player/radio is
soundless
Loudspeaker output line wrong
connected
Panel function setting inaptitude
Loudspeaker damaged
Dirts on connector conducting
point
Replace a new loudspeaker of same specification
Connector wire core disconnected (open
ciercuit)
Internal CD-player/radio
loudspeaker output
Please refer to the connecting method shows on
nameplate
In SEL menu, on panel, BAL and FDA shall be set to 0
Clear the oxide or replace with new outputline of
same specification
Clean the connector or replace it with a new one of
same specification
Replace with new connector of same specification
Replace CD-player/radio assembly
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Normal
Normal
Normal
Normal
Normal
Normal
Abnormal
Disconnected
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст