Geely FC. Manual part — 88
Geely FC. Manual part - 88
Chair--Front chair
Overhaul
Hint:
z
When assembling, please work by the sequence opposite with disassembling sequence, but
when it has items that need to pay special attention, it will add special specification.
z
This overhaul procedure is the disassembling procedure for left side, and the procedure for
right side is same.
349
1. Disassemble driver chair assembly [68010061]
(a) Disassemble fixing clamp.
(b) Use screw driver to disassemble left lower trim board of driver
chair [68010062].
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(c) Use screw driver to disassemble right rear lower trim board
of driver chair [68010065].
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(d) Use screw driver to disassemble right front lower trim board
of driver chair [68010064].
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(e) Disassemble the joint.
(f) Disassemble four bolts and front chair.
Note: Do not damage automobile body.
2. Disassemble front chair pillow assembly [68010066]
3. Disassemble chair vertical adjusting button
Disassemble fixing clamp and chair vertical adjusting
button.
4. Disassemble declining adjustment releasing handle.
Use screw driver to disassemble declining adjustment releas-
ing handle.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
5. Disassemble lower trim cover of front chair gasket.
6. Disassemble inner trim cover of front chair gasket.
Disassemble the screw and inner trim cover of front chair gasket.
7. Disassemble left front safety belt locker assembly
[68010040]
(a) Cut off fixing clasp.
(b) Disassemble the bolt and left/right front safety belt locker
Chair--Front chair
350
assembly.
8. Disassemble chair backrest assembly.
(a) Disassemble the clasp.
(b) Over turn exterior cover of chair backrest , then disassemble the clasp.
(c) Disassemble four bolts and chair backrest assembly.
9. Disassemble exterior cover of chair backrest .
(a) Disassemble head pillow bracket.
(b) Disassemble fixing clamp and adjusting lever of waist support lever.
(c) Disassemble the clamp, then disassemble exterior cover of chair backrest with gasket.
(d) Disassemble the clamp, then disconnect exterior cover of chair backrest with chair backrest gasket.
(e) Disassemble two screws and waist support lever.
10. Disassemble exterior cover of chair gasket.
(a) Disassemble fixing clamp, then disassemble exterior cover of chair backrest with gasket.
(b) Disassemble the clamp, then disconnect exterior cover of chair backrest with chair backrest gasket.
11. Disassemble chair gasket bracket assembly.
12. Disassemble chair front and rear adjusting handle.
Use screw driver to disassemble chair front and rear adjusting handle.
Hint: before using screw driver, it is necessary to wrap its needled top with adhesive tape.
13. Assemble chair gasket bracket assembly.
Use four bolts to assemble chair gasket bracket on chair adjustment assembly.
Torque: 20 N
⋅⋅⋅⋅⋅m
14. Assemble exterior cover of chair gasket.
(a) Use new clamp to assemble exterior cover of chair gasket in chair gasket.
(b) Use new clamp to assemble chair gasket on chair gasket
bracket.
Hint:
z
Do not damage or dirty exterior cover of chair
gasket.
z
When assembling clamp, it is necessary to prevent
exterior cover of chair gasket from crinkling.
15. Assemble exterior cover of chair backrest .
(a) Use new clamp to assemble exterior cover of chair backrest
in chair gasket.
(b) Use new clamp to assemble chair backrest on chair
backrest bracket.
Hint:
z
Do not damage or dirty exterior cover of chair
backrest .
z
When assembling clamp, it is necessary to prevent
Chair--Front chair
Locking loop pliers
Locking loop pliers
351
exterior cover of chair backrest from crinkling.
16. Assemble chair backrest assembly.
(a) Use four bolts to assemble chair backrest assembly.
Torque: 45 N
⋅⋅⋅⋅⋅m
(b) Over turn exterior cover of chair backrest to assemble clamp.
(c) Assemble the clamp.
17. Assemble left front safety belt locking assembly [68010040]
(a) Use the bolt to assemble left front safety belt locking assembly.
Torque: 42 N
⋅⋅⋅⋅⋅m
(b) Assemble fixing clasp.
18. Assemble driver chair assembly.
(a) Assemble driver chair.
Note: do not damage automobile body.
(b) Connect the joint.
(c) Assemble four bolts.
Torque: 47 N
⋅⋅⋅⋅⋅m
(d) Assemble right front lower trim board, right rear lower trim board and left lower trim board of driver chair.
Chair--Rear chair (separating type)
Rear chair (separating type)
Overhaul
Hint:
When assembling, please work by the sequence opposite with
disassembling sequence, but when it has items that need to
pay special attention, it will add special specification.
1. Disassemble rear row chair cushion assembly.
Pull rear row chair cushion assembly upwards, then disas-
semble it.
Note: when disassembling, it is necessary to hold the
bracket at two sides of fixing clasp, then pull it upwards
to prevent it from distorting.
2. Disassemble rear chair head pillow assembly
[68010077]
3. Disassemble rear row chair backrest assembly.
4. Make the backrest face the front, then disassemble
four fixing clamps.
5. Disassemble four bolts and rear chair backrest
assembly.
6. Disassemble rear row chair right backrest assem-
bly [68010079]
Disassemble the bolt and rear row chair right backrest
assembly.
7. Disassemble rear row chair left backrest assembly
[68010078]
Disassemble two bolts and central backrest hinge.
8. Disassemble exterior cover of rear row backrest
(small).
(a) Disassemble fixing clamp, then disassemble rear row chair
gasket cloth.
(b) Disassemble fixing clamp, then disassemble head pillow
bracket.
(c) Disassemble exterior cover of rear row backrest with gasket.
(d) Disassemble the clamp, then disconnect exterior cover of
rear row backrest with gasket.
9. Disassemble exterior cover of rear row backrest (big).
(a) Disassemble central handrail hinge trim cover.
(b) Disassemble the bolt and central handrail.
A:
100mm
Fixing
clasp
Fixing
clasp
352
(c) Disassemble fixing clamp, then disassemble rear row chair gasket cloth.
(d) Disassemble the clamp, then disassemble head pillow bracket.
(e) Disassemble exterior cover of rear row backrest with gasket.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст