Geely FC. Manual part — 76
Geely FC. Manual part - 76
2. Inspect the function of generator
(a) low speed:
Connect battery positive wire with joint terminal SWL, connect negative to terminal ES. Inspect whether
generator work at low speed.
If its function does not in conformity with regulations, replace wiper.
(b) high speed
Connect battery positive wire with joint terminal SWH, connect negative to terminal WS. Inspect
whether generator work at high speed.
If its function does not in conformity with regulations, replace wiper.
(c) Free stop position
(1) Connect battery positive wire with joint terminal SWL, connect negative to terminals ES to make
generator work at low speed. Disassemble terminal SWL
lead to make generator stop except stop position.
(2) Connect terminal SWL with terminal AS
(3) Connect battery positive wire with joint terminal SWL to
make generator work at low speed again. Inspect gen-
erator whether stop at the stop position.
If its function does not in conformity with regulations,
replace wiper.
Wiper and cleaner--Wiper and cleaner system
Free stop
position
301
Wiper and cleaner--Right
combination
switch
Right combination switch
Change
1. Disassemble the lower trim board of the steering
gear
2. Disassemble right combination switch assembly
[67000079]
(a) Disassemble the joints.
(b) Press fixed jaw to separate meshing then disassemble right
combination switch assembly.
Notes: Do not overly press fixed jaw, or it may de
damaged.
302
Fixing
claw
Wiper and cleaner--Wiper generator
Fixing clasp
Fixing
claw
Wiper generator
Change
1. Disassemble wiper arm cap.
2. Disassemble auxiliary wiper arm assembly
[68000059]
Disassemble screw cap and auxiliary wiper arm assembly.
3. Disassemble main wiper arm assembly [68000057]
Disassemble screw cap and main wiper arm assembly.
4. Disassemble generator cap to fire barrier seal.
Separate eight fixed buckles to disassemble the seal from gen-
erator cap to fire barrier.
5. Disassemble ventilation cover on passenger side.
Disassemble five fixed jaws so as to disassemble ventilation
cover on passenger side.
6. Disassemble ventilation cover on driver side.
Disassemble five fixed jaw so as to disassemble ventilation
cover on driver side.
7. Disassemble wiper connecting rod assembly
[68000053]
(a) Disassemble the joint.
(b) Disassemble the bolt.
(c) Slide wiper connecting rod assembly to passenger side to
separate meshing of rubber pin so as to disassemble wiper
connecting nod.
Fixing
claw
303
Pin
Wiper and cleaner--Wiper generator
8. Disassemble wiper generator
(a) Separate two connecting rod caps of shaft pins.
(b) Separate two star- bolts so as to disassemble wiper
generator.
9. Assemble wiper generator
(a) Daub MP grease to connecting rod caps of wiper generator.
(b) Use two Star-bolts to assemble wiper generator to wiper
connecting rod.
Torque: 5.39 N.m
10. Assemble wiper connecting rod assembly
[68000053]
(a) Meshing wiper connecting rod rubber pin
(b) Use two bolts to assemble wiper connecting rod.
Torque:5.5 N.m
(c) Connect the joints.
11. Assemble assistant wiper arm assembly [68000059]
(a) Use steel brush to clean small tooth slot of wiper pivot.
(b) Use bolt cap to fix wiper arm on passenger side to make
wiper blade at the position as drawing.
Torque: 20.5 N.m
12. Assemble main wiper arm assembly [68000057]
(a) Use steel brush to clean small tooth slot of wiper pivot.
(b) Use bolt cap to fix wiper arm on driver side to make wiper
vane at the position as drawing.
Assembly starting and
stopping position
304
Assembly starting and
stopping position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст