Geely FC. Manual part — 75
Geely FC. Manual part - 75
High brake light assembly
Change
1. Disassemble high brake light assembly [67010008]
(a) Loosen two fixed jaw just as drawing.
(b) Loosen two fixed jaw and disassemble high brake light
assembly as the drawing, then take the joint apart.
Light--High brake light assembly
297
Fixing claw
Light--Left
combination
switch
Left combination switch
Change
1. Disassemble decorative board under steering column [67000129]
2. Disassemble left combination switch assembly [67000078]
(a) Take the joint apart.
(b) Loosen fixed jaw and pull left combination switch assembly.
Fixing
claw
298
Malfunction
Wiper and cleaner do not work.
Wiper does not work on LO, HI or MIST.
Wiper does not work on INT
Washer generator does not work
When cleaner switch ON, wiper does not
work.
Wiper cleaner can not spout
z
Right assembled switch on HI, wiper
blade will touch the bodywork.
z
When right combination switches are OFF, washer will
not return to original position or stop position is incorrect.
Component names
1. ignition switch
2. ignition relay
3. (wiper) fuse (central power distribution box)
4. right assembled switch
5. wiring harness
1. right assembled switch
2. wiper generator
3. wiring harness
1. right assembled switch
2. wiper generator
3. wiring harness
1. (washer) fuse (central power distribution box)
2. wiper switch
3. wiper generator
4. wiring harness
1. right assembled switch
2. washer generator
3. wiring harness
1. cleaner hose and nozzle
1. right assembled switch *1
2. wiring harness
Reference pages
-
-
-
302
302
303
302
303
-
-
-
-
302
303
-
-
302
-
Inspect the car
Inspect the function of cleaner generator
(1) Add some rinsing to wiper water tank, then disassemble
cleaner generator joint.
(2) Connect battery wire with cleaner generator joint terminal2,
negative wire with terminal1,then inspect whether cleaner
generator works.
Notes: Be quick(in 20 seconds) to do this test to pre-
vent cleaner generator coil from burning.
If its function does not in accord with regulations, replace
cleaner generator.
Wiper and cleaner--Wiper and cleaner system
Wiper and cleaner
Wiper and cleaner system
Malfunction phenomena table
The underside table can help you to eliminating malfunction in wiring. It sorts as possibilities of malfunction’s
reasons.
*1:inspect set position of wiper arm and wiper blade.
299
Wiper and cleaner--Wiper and cleaner system
Inspect
1. Inspect the conduction of right combination
switch [67000079]
(a) Inspect the conduction of every terminal of joints.
Right combination switch
Switch position
terminals connect with avometer
regular situations
OFF
-
Not conduction
ON
WIG-WS
conduction
Switch positions
terminals connect with avometer
regular situations
MIST
SWL-WIG
Conduction
OFF
AS-SWL
Conduction
INT
AS-SWL/SWL-WIG
Conduction
LO
SWL-WIG
Conduction
HI
SWH-WIG
Conduction
(c) Inspect the function of cleaner
(1) Turn right assembled switch to OFF.
(2) Connect battery positive wire with joint terminal WIG, connect negative to terminal EW.
(3) Connect voltmeter positive wire with joint terminal WS, connect negative to terminal EW.
(4) Switch on cleaner switch and inspect its going.
(b) Inspect intermittent function of wiper.
(1) Connect voltmeter positive wire with joint terminal SWL, connect negative to terminal EW.
(2) Connect battery positive wire with joint terminal WIG, connect negative to terminal EW.
(3) Turn right assembled switch to INT.
(4) Connect battery positive wire with terminal AS for 5 seconds.
(5) Connect battery negative with terminal AS for 5 seconds actuate intermittent relay and check the
voltage between terminal SWL and terminal EW .
Sprinkler switch
300
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст