Geely Emgrand X7. Manual part — 114
Geely Emgrand X7. Manual part - 114
Installation Procedure:
1. Install and tighten the fixing bolts
of engine mount to the specified
torque.
2. Install and tighten the right
engine suspension to the engine
retaining bolts and nuts.
3. Install and tighten the engine
right suspension to the body
bolts.
4. Remove the supporting jack.
5. Install the generator assembly.
6. Install the engine hood.
7. Install negative cable of battery.
GC02-0022c
455
2.6.8.8 Replacement of Timing Chain Tensioner
Dismantlement Procedure
Warning: Refer to "Warning on
Battery Disconnection" in
"Warning and Precautions"!
1. Disconnect the battery negative
electrode cable. Refer to 2.11.8.1
Battery Disconnection.
2. Dismantle the plastic shield of
engine. Refer to 2.6.8.1
Replacement of Plastic Shield of
Engine.
3. Refer to 2.10.8.3 "Replacement
of Ignition Coil" to dismantle the
ignition coil.
10
0
GC02-0024c
4. Refer to 2.6.8.2 "Replacement of
Cylinder Hood Cover" to
dismantle the cylinder hood
cover.
5. Rotate the crankshaft and make
sure the cylinder No.1 is at TDC
position.
Note: Crankshaft timing mark is
aligned with the timing chain cast
scale line "0".
6. As shown in the graphic, mark on
the intake and exhaust sprocket
timing with a marker and use a
special tool GL301-022 to fix the
timing chain and special tool
GL301-018 to fix the camshaft.
GC02-0025c
7. Dismantle Timing Chain
Tensioner Assembly.
Note: At this time do not rotate the
crankshaft in order to prevent the
timing chain teeth rolling.
GC02-2000c
456
Installation Procedure:
1. Press timing chain tensioner pull
rod to keep the tensioner into
selft-lock condition as shown in
figure.
FE02-0138b
2. Install the timing chain shroud
tensioner and tighten the nuts.
Torque:29 Nm(Metric) 21.5
lb-ft(English system)
4. Confirm the tensioner unlocked
and the tensioner guide is firmly
pressed by the handle.
Note: If not properly unlocked, use a
screwdriver to push tensioner in the
opposite direction to unlock the
guide.
5. Install the cylinder hood cover.
6. Install the ignition coil.
7. Install the engine hood.
8. Connect battery negative cable.
GC02-2000c
Up
Enter
Pin
Hook
457
2.6.8.9 Replacement of Timing Chain Cover
Dismantlement Procedure
Warning: Refer to "Warning on Battery Disconnection" and "Warning on Cooling System
maintenance" in "Warning and Precautions".
1. Disconnect the battery negative electrode cable. Refer to 2.12.6.1 Battery Disconnection.
2. Refer to 2.8.8.1 Engine Coolant Discharge and Filling to discharge the engine coolant.
3. Dismantle the plastic shield of engine. Refer to 2.6.8.1 Replacement of Plastic Shield of
Engine.
4. Refer to 2.10.7.3 "Replacement of Ignition Coil" to Dismantle the ignition coil.
5. Refer to 2.6.8.2 "Replacement of Cylinder Hood Cover" to dismantle the cylinder hood
cover.
6. Dismantle the drive belt. Refer to 2.6.8.3 Replacement of Drive Belt.
7. Refer to 2.6.8.4 "Replacement of Drive Belt Tensioner" to dismantle the drive belt tensioner.
8. Dismantle the power steeling pump.
9. Dismantle oil pan, refer to 2.9.8.3
Replacement of Oil Pan.
10. Refer to 2.6.8.8 “Replacement of
Timing Chain Tightener” to
dismantle the timing chain
tightener.
Note: In the confined operating
space, lower the jack to facilitate the
operation.
11. Use special tool to dismantle the
crankshaft pulley.
10
0
GL301-020
GC02-0027c
12. Dismantle the three timing chain
cover M6 tightening bolts and
nuts.
GC02-0028c
458
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст