Geely EC718, EC718RV, EC715, EC715RV. Manual part — 113
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 113
2.6.8.12 Camshaft Replacement
Removal Procedure:
FE02-0177b
1.
Disconnect the battery negative cable. Refer to
.
2.
Remove the engine plastic shield. Refer to
3.
Remove the cylinder head cover. Refer to
4.
Remove the drive belt. Refer to
5.
Remove the timing chain cover. Refer to
6.
Remove the timing chain. Refer to
7.
Remove the intake camshaft VVT actuator.
Note
Remove the camshaft VVT actuator tightening bolt
with a wrench holding the camshaft.
FE02-0178b
8.
Remove the exhaust camshaft sprocket.
Note
Remove the camshaft sprocket tightening bolts with
a wrench holding the camshaft.
Engine
Engine Mechanical System JL4G18-D
2-367
9
11
6
4
3
5
1
7
10
8
2
FE02-0179b
9.
As shown in the graphic, gradually release the camshaft
bearing cap bolts, rotate half a circle to a whole circle each
time.
Note
Be careful when remove the camshaft. Avoid
abrasions, scratches or damage to the camshaft
surface or bearing surface.
FE02-0180b
10. Remove the camshaft.
Note
Camshaft must be withdraw from the bearing in
order to avoid abrasions, scratches or damage to
the camshaft surface or bearing surface.
11. Inspect for the camshaft and bearing wear. If necessary,
replace.
Installation Procedure:
Note
Be careful when install the camshaft. Avoid abrasions,
scratches or damage to the camshaft surface or bearing
surface.
Note
Before installation apply engine oil to the camshaft and
the seal contacting surface.
2-368
Engine Mechanical System JL4G18-D
Engine
FE02-0181b
1.
Apply a small amount of engine oil to lubricate the journal
and camshaft cap.
2.
Install the exhaust camshaft.
FE02-0182b
3.
Install the intake camshaft.
FE02-0183b
4.
Install the intake and exhaust camshaft cover.
Note
There are letters on the camshaft cover. Avoid
installation errors. For example, "I ↑ 2" indicates that
the camshaft cover is the No.2 intake camshaft
cover. The arrow is toward the direction of timing
chain. "E ↑ 2 indicates the No.2 exhaust camshaft
cover. The arrow is toward the direction of timing
chain.
Engine
Engine Mechanical System JL4G18-D
2-369
3
1
6
8
9
7
11
5
2
4
10
FE02-0184b
5.
Gradually tighten the camshaft cover bolts according to
the sequence as shown in the graphic.
Note
Tighten the bolts during several stages. Do not
tighten at once which may damage the camshaft
and the camshaft cover.
Torque:
M6 Bolts 13 Nm (Metric) 10 lb-ft (US English)
M8 Bolts 23 Nm (Metric) 17 lb-ft (US English)
FE02-0185b
6.
Install the exhaust camshaft sprocket.
Note
Check for the sprocket pin wear. IF there is wear,
replace the sprocket pin. Hold the camshaft with a
wrench and then tighten the VVT actuator bolts.
Torque: 55 Nm (Metric) 41 lb-ft (US English)
FE02-0186b
7.
Install the intake camshaft VVT actuator.
Note
Check for the sprocket pin wear. Hold the camshaft
with a wrench and then tighten the sprocket bolts.
Torque: 70 Nm (Metric) 52 lb-ft (US English)
8.
Install the timing chain.
9.
Install the timing chain cover.
10. Install the drive belt
11. Install the cylinder head cover.
12. Install the engine plastic shield.
13. Connect the battery negative cable.
2-370
Engine Mechanical System JL4G18-D
Engine
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст