Geely EC718, EC718RV, EC715, EC715RV. Manual part — 306
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 306
1 2 3 4 5 6 7 8 9 10
21
20
19
18
17
16
15
14
13
12
11
22
To Floor Harness (Right) Connector IP49
FE06-5505b
Yes
Step 4
Check the wiring harness (instrument cluster - power, ground).
15 14 13 12
10 9 8 7 6 5 4 3 2 1
16
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
Instrument Cluster Harness Connector IP03
FE09-5105b
(a)
Turn the ignition switch to OFF.
(b)
Disconnect the battery negative cable.
(c)
Disconnect the instrument cluster connector IP03.
(d)
Connect the battery negative cable.
(e)
Turn the ignition switch to ON (IG).
(f)
Measure voltage between the connector IP03 terminals No.
24,32 and the body ground respectively, with a multimeter
Standard Voltage Value: 11-14 V
(g)
Turn the ignition switch to OFF.
(h)
Measure resistance between the connector IP03 terminals
No.15,16 and the body ground respectively, with a multimeter
Standard Resistance: Less than 1 Ω
Is the value the specified value?
No
Check the fuses, repair or replace the wiring
harness
Yes
Step 5
Replace the instrument cluster.
(a)
Replace the instrument cluster. Refer to
.
(b)
Confirm that the repair is completed.
Next
Step 6
System normal.
Brake System
Parking System
6-57
6.5.5 Removal and Installation
6.5.5.1 Park Brake Control Mechanism Switch
Replacement
Removal Procedure:
Warning!
Refer to "Battery Disconnect Warning" in "Warnings and
Notices".
FE06-0064b
1.
Disconnect the negative battery cable and wait for the 90s
and above. Refer to
.
2.
Release the park brake control mechanism assembly.
3.
Remove the center console. Refer to
4.
Disconnect the park brake control mechanism switch
wiring harness connector.
5.
Remove the park brake control mechanism switch
retaining bolts.
Installation Procedure:
FE06-0065b
1.
Install the park brake control mechanism switch retaining
bolts.
Torque: 21 Nm (Metric) 15.5 lb-ft (US English)
2.
Connect the park brake control mechanism switch wiring
harness connector.
3.
Install the center console.
4.
Apply the park brake control mechanism.
5.
Connect the battery negative cable.
6-58
Parking System
Brake System
6.5.5.2 Park Brake Control Mechanism
Assembly Replacement
Removal Procedure:
FE06-0066b
1.
Release the park brake control mechanism assembly.
2.
Remove the center console. Refer to
3.
Disconnect the park brake control mechanism switch
wiring harness connector.
4.
Measure the thead length between to the handle top to
the hexagonal nut and record it.
FE06-0067b
5.
Remove the park brake control mechanism assembly
cable adjuster nut and gasket.
FE06-0068b
6.
Open the park brake control mechanism assembly park
brake handle installation pad and pull out of the park brake
cable.
Brake System
Parking System
6-59
FE06-0069b
7.
Remove the park brake control mechanism assembly
handle assembly to the body bottom retaining bolts.
8.
Remove the park brake control mechanism assembly
handle assembly.
Installation Procedure:
FE06-0070b
1.
Install the park brake control mechanism assembly handle
assembly.
Note
Refer to "Fastener Notice" in "Warnings and
Notices".
2.
Install the park brake control mechanism assembly handle
assembly to the body bottom retaining bolts.
Torque: 21 Nm (Metric) 15.5 lb-ft (US English)
FE06-0071b
3.
Install the park brake control mechanism assembly park
brake handle installation pad and install the park brake
handle assembly.
6-60
Parking System
Brake System
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст