Geely EC718, EC718RV, EC715, EC715RV. Manual part — 509
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 509
12.3.3.8 Fuel Filler Cap Release Handle
Replacement
Removal Procedure:
FE12-0140b
1.
Remove the driver electric seat. Refer to
.
2.
Remove the driver door and the left rear door sill
nameplate. Refer to
3.
Remove center pillar lower trim panel. Refer to
Center Pillar Trim Panel Replacement
.
4.
Remove the rear seat back bolster. Refer to
Seat Armrest Assembly Replacement
5.
Lift the car carpet and remove the fuel filler cap release
handle retaining bolts.
2
2
1
FE12-0141b
6.
Remove the rear compartment trim panel. Refer to
Rear Compartment Trim Panel Replacement
7.
Disconnect the fuel filler cap release cable (1) from inside
the vehicle.
Note
Rotate the fuel filler door lock actuator counter
clockwise to loose the cable (1), and then pull the
cable out of the fuel filler door lock actuator (2).
8.
Remove the fuel filler door lock actuator (2).
9.
From the driver side, pull the fuel filler cap release cable
with the handle out of the vehicle.
Installation Procedure:
FE12-0142b
1.
Install and tighten the fuel filler cap release handle
retaining bolts.
Torque: 10 Nm (Metric) 7.4 lb-ft (US English)
2.
Route the release cable.
Note
Route the release cable the same as before
removal.
Body, Sheet Metal and Painting
Body Rear End
12-25
2
2
1
FE12-0143b
3.
Install the fuel filler door lock actuator (2) to the fuel filler
neck.
4.
Connect the fuel filler cap release cable (1) to the fuel filler
door lock actuator (2).
5.
Install the rear compartment trim panel.
6.
Install the rear seat back bolster.
7.
Install the center pillar lower trim panel.
8.
Install the driver door and the left rear door sill nameplate.
9.
Install the driver electric seat.
12.3.3.9 Hatchback Latch Replacement
Removal Procedure:
1
2
2
FE12-0144c
1.
Remove the hatchback inner trim panel. Refer to
Hatchback Inner Trim Panel Replacement
.
2.
Disconnect the latch release cable from the hatchback
latch.
3.
Remove the hatchback latch retaining nut (2).
4.
Remove the hatchback latch.
Installation Procedure:
1
2
2
FE12-0144c
1.
Install and tighten the hatchback latch retaining nut.
Torque: 10 Nm (Metric) 7.4 lb-ft (US English)
2.
Connect the latch release cable to the hatchback latch.
3.
Install the hatchback inner trim panel.
12-26
Body Rear End
Body, Sheet Metal and Painting
12.4 Bumpers
12.4.1 Specifications
12.4.1.1 Fastener Tightening Specifications
Application
Model
Specification
Metric (Nm)
US English (lb-ft)
Front Bumper Retaining Bolts
M6 × 16
9-13
6.7-9.6
Rear Bumper Retaining Bolts
M6 × 16
9-13
6.7-9.6
Rear Bumper Retaining Bolts
M6 × 12
9-13
6.7-9.6
Front/Rear Impact Bar
Retaining Nuts
M10
70
51.80
Body, Sheet Metal and Painting
Bumpers
12-27
12.4.2 Component Locator
12.4.2.1 Component Views
1
4
3
2
FE12-1003b
Legend
1. Front Bumper Assembly
2. Front Impact Bar
3. Rear Impact Bar
4. Rear Bumper Assembly
12-28
Bumpers
Body, Sheet Metal and Painting
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст