Geely EC718, EC718RV, EC715, EC715RV. Manual part — 429
Geely EC718, EC718RV, EC715, EC715RV. Manual part - 429
Wiper Switch Harness Connector IP19
Front Wiper Motor Harness Connector CA14
FE11-5507b
(a)
Check and repair the open circuit between the windshield
wiper switch and wiper motor.
(b)
Confirm the circuit between the windshield wiper switch and
wiper motor is working properly.
Confirm the repair completed.
Next
Step 10
System normal.
11.6.7.4 Wiper Inoperative At High Speed
Schematic:
Wiper Inoperative At All Speed
Diagnostic Steps:
Step 1
Check the wiper motor harness connector terminal No.4 voltage.
Front Wiper Motor Harness Connector CA14
FE11-5508b
(a)
Turn on the ignition switch.
(b)
Turn the wiper switch to "HI" (high speed) position.
(c)
Measure the wiper motor wiring harness connector terminal
No.4 voltage with a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
No
Body Electric
Wipers / Washers System
11-229
Yes
Step 2
Replace the wiper motor.
(a)
Replace the wiper motor repair. Refer to
Is the wiper motor working correctly?
Yes
System normal
No
Step 3
the wiper switch continuity.
Wiper Switch Harness Connector IP19
FE11-5509b
(a)
Turn the wiper switch to "HI" (high speed) position.
(b)
Measure resistance between the wiper switch terminals No.
11 and 8 and check the wiper switch continuity with a
multimeter.
Resistance Standard Value: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 4
Replace the wiper switch.
(a)
Replace the wiper switch. Refer to
Are the wipers working properly?
Yes
System normal
No
Step 5
Check the circuit between the wiper switch wiring harness connector terminal No.8 and the wiper motor
wiring harness connector terminal No.4.
11-230
Wipers / Washers System
Body Electric
Wiper Switch Harness Connector IP19
Front Wiper Motor Harness Connector CA14
FE11-5510b
(a)
Check the circuit between the wiper switch wiring harness
connector terminal No.8 and the wiper motor wiring harness
connector terminal No.4.
(b)
Repair the open circuit between the wiper switch wiring
harness connector terminal No.8 and the wiper motor wiring
harness connector terminal No.4.
Confirm the repair completed.
Next
Step 6
System normal.
11.6.7.5 Wiper Inoperative At Low Speed
Schematic:
Wiper Inoperative At All Speed
Diagnostic Steps:
Step 1
Measure the wiper motor harness connector terminal No.1 voltage.
Front Wiper Motor Harness Connector CA14
FE11-5503b
(a)
Turn on the ignition switch.
(b)
Turn the wiper switch to "LOW" (low speed) position.
(c)
Measure the wiper motor harness connector terminal No.1
voltage with a multimeter.
Standard Voltage: 11-14 V
Is the voltage specified value?
No
Body Electric
Wipers / Washers System
11-231
Yes
Step 2
Replace the wiper motor.
(a)
Replace the wiper motor repair. Refer to
Is the wiper motor working correctly?
Yes
System normal
No
Step 3
Check the wiper switch.
Wiper Switch Harness Connector IP19
FE55-5506b
(a)
Turn the wiper switch to "LOW" (low speed) position.
(b)
Measure resistance between wiper switch terminals No.11
and 7 and check the wiper switch Continuity with a
multimeter.
Resistance Standard Value: Less than 1 Ω
Is the resistance specified value?
Yes
No
Step 4
Replace the wiper switch.
(a)
Replace the wiper switch. Refer to
Are the wipers working properly?
Yes
System normal
No
Step 5
Check the circuit between the wiper switch wiring harness connector terminal No.7 and the wiper motor
wiring harness connector terminal No.1.
11-232
Wipers / Washers System
Body Electric
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст